I have a laptop, which has FC4 installed. Fedora can detect my sound card (82801DB), however... there're no sound during the sound test. I've checked the setting in the ALSA MIXER. I ensure that the mixer's setting is correct.
It sounds that, the AC97 modem will conflict with the AC97 sound in the centrino platform. I've put the module of AC97 modem into /etc/hotplug/blacklist. But it still appear in "lsmod". And I ran "aplay -t xxx.wav" it appears an error message:
e.g. [root@localhost ~]# aplay -t /usr/share/gok/goksound2.wav
aplay: main:419: unrecognized file format /usr/share/gok/goksound2.wav
I have read many articles in fedoraforum and linuxquestion.org. Suggested solutions are most likely put the modem module in the blacklist, ALSAMIXER. I can't solve the problem by now. So I seek for help here.
CONFIG FILE ARE LISTED AS BELOW
[root@simon_laptop ~]# dmesg
Linux version 2.6.12-1.1398_FC4 (bhcompile@tweety.build.redhat.com) (gcc version 4.0.0 20050519 (Red Hat 4.0.0-icon_cool.gif) #1 Fri Jul 15 00:52:32 EDT 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fffffc0 (ACPI data)
BIOS-e820: 000000001fffffc0 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 131056
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126960 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 OID_00 ) @ 0x000e6010
ACPI: RSDT (v001 INSYDE RSDT_000 0x00000001 _CSI 0x00010101) @ 0x1fffb040
ACPI: FADT (v001 COMAPL CL20_000 0x00000100 _CSI 0x00010101) @ 0x1ffffa90
ACPI: BOOT (v001 INSYDE SYS_BOOT 0x00000100 _CSI 0x00010101) @ 0x1ffffb90
ACPI: NONE (v001 INSYDE NONE_000 0x30303030 0000 0x30303030) @ 0x1ffffb20
ACPI: SSDT (v001 INSYDE GV3Ref 0x00002000 INTL 0x20021002) @ 0x1fffb080
ACPI: DSDT (v001 INSYDE Canyon 0x00001004 INTL 0x02002036) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
Allocating PCI resources starting at 20000000 (gap: 20000000:dfb80000)
Built 1 zonelists
Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet
Initializing CPU#0
CPU 0 irqstacks, hard=c0454000 soft=c0453000
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1495.376 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 513208k/524224k available (2508k kernel code, 10352k reserved, 684k data, 184k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 2965.50 BogoMIPS (lpj=1482752)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9f9bf 00000000 00000000 00000000 00000180 00000000 00000000
CPU: After vendor identify, caps: afe9f9bf 00000000 00000000 00000000 00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9f1bf 00000000 00000000 00000040 00000180 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel(R) Pentium(R) M processor 1.50GHz stepping 06
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0c00)
checking if image is initramfs... it is
Freeing initrd memory: 1668k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xe9c64, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI2._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 5 7 9 *10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 5 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 5 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKG] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 5 7 9 10 *11)
ACPI: Embedded Controller [EC0] (gpe 2icon_cool.gif
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:06: ioport range 0x300-0x30f has been reserved
pnp: 00:06: ioport range 0x1000-0x107f could not be reserved
pnp: 00:06: ioport range 0x1300-0x133f has been reserved
Simple Boot Flag at 0x37 set to 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1125081694.050:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 57652F2F3358E32D
- User ID: Red Hat, Inc. (Kernel Module GPG key)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 855PM Chipset.
agpgart: AGP aperture is 64M @ 0xb0000000
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 76 ports, IRQ sharing enabled
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.6 -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
ICH4: chipset revision 3
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1100-0x1107, BIOS settings: hda
MA, hdb
io
ide1: BM-DMA at 0x1108-0x110f, BIOS settings: hdc
MA, hdd
io
Probing IDE interface ide0...
hda: HTS548080M9AT00, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: TOSHIBA DVD-ROM SD-R2512, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 156301488 sectors (80026 MB) w/7877KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 < hda5 hda6 hda7 hda8 >
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 32Kbytes
TCP established hash table entries: 32768 (order: 6, 262144 bytes)
TCP bind hash table entries: 32768 (order: 7, 917504 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI wakeup devices:
PWRB PCI2 LAN USB0 USB1 USB2 MC97
ACPI: (supports S0 S1 S3 S4 S4bios S5)
Freeing unused kernel memory: 184k freed
device-mapper: 4.4.0-ioctl (2005-01-12) initialised:
dm-devel@redhat.com
input: AT Translated Set 2 keyboard on isa0060/serio0
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
alps.c: Enabling hardware tapping
input: PS/2 Mouse on isa0060/serio4
input: AlpsPS/2 ALPS GlidePoint on isa0060/serio4
alps.c: Enabling hardware tapping
input: PS/2 Mouse on isa0060/serio4
input: AlpsPS/2 ALPS GlidePoint on isa0060/serio4
security: 3 users, 6 roles, 830 types, 95 bools
security: 55 classes, 196440 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), not configured for labeling
SELinux: initialized (dev hugetlbfs, type hugetlbfs), not configured for labeling
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
floppy0: no floppy controllers found
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 11
ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [LNKF] -> GSI 11 (level, low) -> IRQ 11
eth0: RealTek RTL8139 at 0xa000, 00:02:3f:07:f1:2c, IRQ 11
eth0: Identified 8139 chip type 'RTL-8101'
ieee80211_crypt: registered algorithm 'NULL'
ipw2100: Intel(R) PRO/Wireless 2100 Network Driver, 1.0.3
ipw2100: Copyright(c) 2003-2004 Intel Corporation
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11
ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNKG] -> GSI 11 (level, low) -> IRQ 11
ipw2100: Detected Intel PRO/Wireless 2100 Network Connection
snd_intel8x0: Unknown parameter `'
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 49452 usecs
intel8x0: clocking to 48000
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1f.6 to 64
hw_random: RNG not detected
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: irq 11, io mem 0xf4000000
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
USB Universal Host Controller Interface driver v2.2
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 10, io base 0x00001200
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001600
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 11, io base 0x00001700
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
usb 3-1: new low speed USB device using uhci_hcd and address 2
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
Yenta: CardBus bridge found at 0000:02:04.0 [14c0:0012]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.0, mfunc 0x00111c12, devctl 0x44
input: USB HID v1.10 Mouse [Microsoft Microsoft Wireless Intellimouse Explorer\uffff 1.0A] on usb-0000:00:1d.1-1
Yenta: ISA IRQ mask 0x0068, PCI irq 10
Socket status: 30000006
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1250 $ Ben Collins
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKE] -> GSI 11 (level, low) -> IRQ 11
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[d0001800-d0001fff] Max Packet=[2048]
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023f4649400181]
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03e3840(lo)
IPv6 over IPv4 tunneling driver
codec_semaphore: semaphore is not ready [0x1][0x701300]
codec_write 1: semaphore is not ready for register 0x54
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Lid Switch [LID]
ibm_acpi: ec object not found
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev hda7, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 1048568k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (4095 buckets, 32760 max) - 272 bytes per conntrack
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0x100-0x4ff: excluding 0x230-0x237 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0xa00-0xaff: clean.
eth0: link down
ieee80211_crypt: registered algorithm 'WEP'
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.7
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.7
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM ver 1.5
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
lp0: using parport0 (interrupt-driven).
lp0: console ready
eth1: no IPv6 routers present
application mixer_applet2 uses obsolete OSS audio interface
application firefox-bin uses obsolete OSS audio interface
codec_semaphore: semaphore is not ready [0x1][0x701300]
codec_write 0: semaphore is not ready for register 0x2c
lsmod:
[root@simon_laptop ~]# lsmod
Module Size Used by
parport_pc 28933 1
lp 13001 0
parport 40585 2 parport_pc,lp
autofs4 29253 2
rfcomm 42333 0
l2cap 30661 5 rfcomm
bluetooth 56133 4 rfcomm,l2cap
sunrpc 167813 1
arc4 1985 1
ieee80211_crypt_wep 4929 1
pcmcia 29025 2
ipt_REJECT 5569 1
ipt_state 1857 3
ip_conntrack 41497 1 ipt_state
iptable_filter 2881 1
ip_tables 19393 3 ipt_REJECT,ipt_state,iptable_filter
video 15941 0
button 6609 0
battery 9413 0
ac 4805 0
md5 4033 1
ipv6 267841 8
ohci1394 41353 0
ieee1394 304441 1 ohci1394
yenta_socket 21449 1
rsrc_nonstatic 12737 1 yenta_socket
pcmcia_core 50909 3 pcmcia,yenta_socket,rsrc_nonstatic
uhci_hcd 35153 0
ehci_hcd 41037 0
i2c_i801 8781 0
i2c_core 21569 1 i2c_i801
snd_intel8x0m 19589 0
snd_intel8x0 34689 1
snd_ac97_codec 75961 2 snd_intel8x0m,snd_intel8x0
snd_seq_dummy 3653 0
snd_seq_oss 37057 0
snd_seq_midi_event 9153 1 snd_seq_oss
snd_seq 62289 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_seq_device 8781 3 snd_seq_dummy,snd_seq_oss,snd_seq
snd_pcm_oss 51185 0
snd_mixer_oss 17857 2 snd_pcm_oss
snd_pcm 100169 4 snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_timer 33605 2 snd_seq,snd_pcm
snd 57157 10 snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_o ss,snd_pcm,snd_timer
soundcore 10913 2 snd
snd_page_alloc 9669 3 snd_intel8x0m,snd_intel8x0,snd_pcm
ipw2100 87417 0
ieee80211 23109 1 ipw2100
ieee80211_crypt 7493 2 ieee80211_crypt_wep,ieee80211
8139too 30017 0
mii 5441 1 8139too
joydev 9601 0
dm_snapshot 17413 0
dm_zero 2113 0
dm_mirror 26157 0
ext3 132681 2
jbd 86233 1 ext3
dm_mod 58101 6 dm_snapshot,dm_zero,dm_mirror
[root@simon_laptop ~]# lspci
00:00.0 Host bridge: Intel Corporation 82855PM Processor to I/O Controller (rev 21)
00:01.0 PCI bridge: Intel Corporation 82855PM Processor to AGP Controller (rev 21)
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 83)
00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 03)
00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 03)
00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 03)
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 03)
00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 03)
01:00.0 VGA compatible controller: nVidia Corporation NV34M [GeForce FX Go5200] (rev a1)
02:00.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link)
02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
02:02.0 Network controller: Intel Corporation PRO/Wireless LAN 2100 3B Mini PCI Adapter (rev 04)
02:04.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus Controller (rev 01)
