hi all,
i'm using Ubuntu 8.04 and kernel 2.6.24-19-generic. I have Ndiswrapper for WiFi USB adapter IOData WN-B11 USBSL.
in dmesg i see the following errors when i plugin the adapter.

[ 410.865011] BUG: unable to handle kernel paging request at virtual address e3e60728
[ 410.865022] printing eip: e0e35c65 *pde = 00000000
[ 410.865033] Oops: 0002 [#1] SMP

Anyway the adapter works properly but i cannot use any USB Pen Drive and removing ndiswrapper (modprobe -r ndiswrapper) or giving lsusb freeze the shell. Anything is ok until i plug the wifi adapter

can anybody help me please?
thanks
vi3da

p.s. the part of dmesg output...sorry but i can't post attachments

p.s.2. with this kernel i don't see my second hdd no more. if i use older kernel (2.6.20-17) yes. Why?



[ 26.668498] uhci_hcd 0000:00:07.2: UHCI Host Controller
[ 26.669275] uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
[ 26.669322] uhci_hcd 0000:00:07.2: irq 9, io base 0x0000d400
[ 26.669680] usb usb1: configuration #1 chosen from 1 choice
[ 26.669738] hub 1-0:1.0: USB hub found
[ 26.669754] hub 1-0:1.0: 2 ports detected
[ 26.673284] 8139too Fast Ethernet driver 0.9.28
[ 26.771490] ACPI: PCI Interrupt 0000:00:07.3[D] -> Link [LNKD] -> GSI 9 (level, low) -> IRQ 9
[ 26.771525] uhci_hcd 0000:00:07.3: UHCI Host Controller
[ 26.771587] uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
[ 26.771626] uhci_hcd 0000:00:07.3: irq 9, io base 0x0000d000
[ 26.771916] usb usb2: configuration #1 chosen from 1 choice
[ 26.771971] hub 2-0:1.0: USB hub found
[ 26.771987] hub 2-0:1.0: 2 ports detected
[ 26.877458] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
[ 26.877472] PCI: setting IRQ 10 as level-triggered
[ 26.877480] ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
[ 26.878280] eth0: RealTek RTL8139 at 0xa000, 00:50:ba:d1:69:d1, IRQ 10
[ 26.878287] eth0: Identified 8139 chip type 'RTL-8139B'
[ 27.970595] Driver 'sd' needs updating - please use bus_type methods
[ 27.971252] sd 0:0:0:0: [sda] 40031712 512-byte hardware sectors (20496 MB)
[ 27.971293] sd 0:0:0:0: [sda] Write Protect is off
[ 27.971299] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 27.971344] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 27.971480] sd 0:0:0:0: [sda] 40031712 512-byte hardware sectors (20496 MB)
[ 27.971505] sd 0:0:0:0: [sda] Write Protect is off
[ 27.971511] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00

[ 27.971551] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 27.971566] sda:<4>Driver 'sr' needs updating - please use bus_type methods
[ 28.600031] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
[ 28.600047] ata1.00: BMDMA stat 0x64
[ 28.600062] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 28.600066] res 51/84:00:07:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
[ 28.600073] ata1.00: status: { DRDY ERR }
[ 28.600078] ata1.00: error: { ICRC ABRT }
[ 28.600138] ata1: soft resetting link
[ 28.802560] ata1.00: configured for UDMA/66
[ 28.810195] ata1.01: configured for UDMA/66
[ 28.810239] ata1: EH complete
[ 29.440805] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
[ 29.440821] ata1.00: BMDMA stat 0x64
[ 29.440837] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 29.440841] res 51/84:00:07:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
[ 29.440848] ata1.00: status: { DRDY ERR }
[ 29.440853] ata1.00: error: { ICRC ABRT }
[ 29.440912] ata1: soft resetting link
[ 29.642060] ata1.00: configured for UDMA/66
[ 29.657673] ata1.01: configured for UDMA/66
[ 29.657714] ata1: EH complete
[ 30.281594] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
[ 30.281609] ata1.00: BMDMA stat 0x64
[ 30.281624] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 30.281628] res 51/84:00:07:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
[ 30.281636] ata1.00: status: { DRDY ERR }
[ 30.281640] ata1.00: error: { ICRC ABRT }
[ 30.281699] ata1: soft resetting link
[ 30.485502] ata1.00: configured for UDMA/66
[ 30.501171] ata1.01: configured for UDMA/66
[ 30.501211] ata1: EH complete
[ 31.133429] ata1.00: limiting speed to UDMA/44:PIO4
[ 31.133445] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
[ 31.133454] ata1.00: BMDMA stat 0x64
[ 31.133468] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 31.133472] res 51/84:00:07:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
[ 31.133479] ata1.00: status: { DRDY ERR }
[ 31.133484] ata1.00: error: { ICRC ABRT }
[ 31.133542] ata1: soft resetting link
[ 31.336985] ata1.00: configured for UDMA/44
[ 31.353788] ata1.01: configured for UDMA/66
[ 31.353841] ata1: EH complete
[ 31.367353] sda1
[ 31.367545] sd 0:0:0:0: [sda] Attached SCSI disk
[ 31.369353] sd 0:0:0:0: [sda] 40031712 512-byte hardware sectors (20496 MB)
[ 31.369481] sd 0:0:1:0: [sdb] 78165360 512-byte hardware sectors (40021 MB)
[ 31.369510] sd 0:0:1:0: [sdb] Write Protect is off
[ 31.369516] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 31.369538] sd 0:0:0:0: [sda] Write Protect is off
[ 31.369544] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 31.369600] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 31.369633] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 31.369788] sd 0:0:0:0: [sda] 40031712 512-byte hardware sectors (20496 MB)
[ 31.369811] sd 0:0:0:0: [sda] Write Protect is off
[ 31.369817] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 31.369855] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 31.369898] sd 0:0:1:0: [sdb] 78165360 512-byte hardware sectors (40021 MB)
[ 31.369921] sd 0:0:1:0: [sdb] Write Protect is off
[ 31.369926] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 31.369963] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 31.369993] sd 0:0:1:0: [sdb] 78165360 512-byte hardware sectors (40021 MB)
[ 31.370016] sd 0:0:1:0: [sdb] Write Protect is off
[ 31.370021] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 31.370059] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 31.370070] sdb: sdb1 sdb2 sdb3
[ 31.401001] sd 0:0:1:0: [sdb] Attached SCSI disk
[ 31.430097] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 31.430145] sd 0:0:1:0: Attached scsi generic sg1 type 0
[ 31.430188] sr 1:0:0:0: Attached scsi generic sg2 type 5
[ 31.430228] scsi 1:0:1:0: Attached scsi generic sg3 type 5
[ 31.435687] sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
[ 31.435705] Uniform CD-ROM driver Revision: 3.20
[ 31.435871] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 31.441952] sr1: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
[ 31.442117] sr 1:0:1:0: Attached scsi CD-ROM sr1
[ 32.363987] Attempting manual resume
[ 32.363999] swsusp: Resume From Partition 8:19
[ 32.364003] PM: Checking swsusp image.
[ 32.364703] PM: Resume from disk failed.
[ 32.438935] kjournald starting. Commit interval 5 seconds
[ 32.438985] EXT3-fs: mounted filesystem with ordered data mode.
[ 45.539456] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 45.651830] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
[ 48.831692] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 48.997819] Linux agpgart interface v0.102
[ 49.082125] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 49.309733] agpgart: Detected VIA Twister-K/KT133x/KM133 chipset
[ 49.313204] agpgart: AGP aperture is 32M @ 0xfc000000
[ 49.376469] parport_pc: VIA 686A/8231 detected
[ 49.376481] parport_pc: probing current configuration
[ 49.376502] parport_pc: Current parallel port base: 0x378
[ 49.376587] parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
[ 49.473547] parport_pc: VIA parallel port: io=0x378, irq=7
[ 56.075928] NVRM: loading NVIDIA Linux x86 Kernel Module 96.43.05 Tue Jan 22 19:36:58 PST 2008
[ 56.512594] ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 62.163406] lp0: using parport0 (interrupt-driven).
[ 62.235115] PPP generic driver version 2.4.2
[ 62.399404] Adding 979956k swap on /dev/sdb3. Priority:-1 extents:1 across:979956k
[ 63.064412] EXT3 FS on sdb2, internal journal
[ 66.306942] No dock devices found.
[ 67.315752] powernow: No powernow capabilities detected
[ 68.261599] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
[ 68.261619] ata1.01: BMDMA stat 0x64
[ 68.261636] ata1.01: cmd ca/00:20:38:12:75/00:00:00:00:00/f3 tag 0 dma 16384 out
[ 68.261640] res 51/84:00:38:12:75/00:00:00:00:00/f3 Emask 0x10 (ATA bus error)
[ 68.261648] ata1.01: status: { DRDY ERR }
[ 68.261653] ata1.01: error: { ICRC ABRT }
[ 68.261711] ata1: soft resetting link
[ 68.462594] ata1.00: configured for UDMA/44
[ 68.470250] ata1.01: configured for UDMA/66
[ 68.470284] ata1: EH complete
[ 68.470881] sd 0:0:0:0: [sda] 40031712 512-byte hardware sectors (20496 MB)
[ 68.471417] sd 0:0:0:0: [sda] Write Protect is off
[ 68.471426] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 68.472047] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 68.473121] sd 0:0:1:0: [sdb] 78165360 512-byte hardware sectors (40021 MB)
[ 68.473490] sd 0:0:1:0: [sdb] Write Protect is off
[ 68.473499] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 68.475165] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 68.617660] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
[ 68.617673] ata1.01: BMDMA stat 0x64
[ 68.617689] ata1.01: cmd ca/00:b0:a0:15:75/00:00:00:00:00/f3 tag 0 dma 90112 out
[ 68.617693] res 51/84:00:a0:15:75/00:00:00:00:00/f3 Emask 0x10 (ATA bus error)
[ 68.617700] ata1.01: status: { DRDY ERR }
[ 68.617705] ata1.01: error: { ICRC ABRT }
[ 68.617761] ata1: soft resetting link
[ 68.822369] ata1.00: configured for UDMA/44
[ 68.830053] ata1.01: configured for UDMA/66
[ 68.830082] ata1: EH complete
[ 68.855410] sd 0:0:1:0: [sdb] Write Protect is off
[ 68.855415] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 68.855456] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 69.562152] ppdev: user-space parallel port driver
[ 69.892463] NET: Registered protocol family 10
[ 69.893922] lo: Disabled Privacy Extensions
[ 70.049049] audit(1222599242.150:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=5006 profile="/usr/sbin/cupsd" namespace="default"
[ 70.151695] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 70.151712] apm: overridden by ACPI.
[ 76.280518] Bluetooth: Core ver 2.11
[ 76.284956] NET: Registered protocol family 31
[ 76.284971] Bluetooth: HCI device and connection manager initialized
[ 76.284982] Bluetooth: HCI socket layer initialized
[ 76.361327] Bluetooth: L2CAP ver 2.9
[ 76.361342] Bluetooth: L2CAP socket layer initialized
[ 76.531499] Bluetooth: RFCOMM socket layer initialized
[ 76.531544] Bluetooth: RFCOMM TTY layer initialized
[ 76.531549] Bluetooth: RFCOMM ver 1.8
[ 78.670892] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[ 78.671692] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[ 78.672374] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[ 127.377255] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
[ 127.377278] ata1.01: BMDMA stat 0x64
[ 127.377294] ata1.01: cmd ca/00:00:a0:ef:31/00:00:00:00:00/f3 tag 0 dma 131072 out
[ 127.377297] res 51/84:00:a0:ef:31/00:00:00:00:00/f3 Emask 0x10 (ATA bus error)
[ 127.377305] ata1.01: status: { DRDY ERR }
[ 127.377310] ata1.01: error: { ICRC ABRT }
[ 127.377371] ata1: soft resetting link
[ 127.634917] ata1.00: configured for UDMA/44
[ 127.642640] ata1.01: configured for UDMA/66
[ 127.642682] ata1: EH complete
[ 127.786186] ata1.01: limiting speed to UDMA/44:PIO4
[ 127.786205] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
[ 127.786214] ata1.01: BMDMA stat 0x64
[ 127.786229] ata1.01: cmd ca/00:00:a0:ef:31/00:00:00:00:00/f3 tag 0 dma 131072 out
[ 127.786233] res 51/84:00:a0:ef:31/00:00:00:00:00/f3 Emask 0x10 (ATA bus error)
[ 127.786241] ata1.01: status: { DRDY ERR }
[ 127.786245] ata1.01: error: { ICRC ABRT }
[ 127.786300] ata1: soft resetting link
[ 127.990700] ata1.00: configured for UDMA/44
[ 127.998392] ata1.01: configured for UDMA/44
[ 127.998430] ata1: EH complete
[ 127.998707] sd 0:0:0:0: [sda] 40031712 512-byte hardware sectors (20496 MB)
[ 151.495859] usb 2-2: new full speed USB device using uhci_hcd and address 2
[ 151.674008] usb 2-2: configuration #1 chosen from 1 choice
[ 151.896960] usbcore: registered new interface driver libusual
[ 152.022960] Initializing USB Mass Storage driver...
[ 152.050891] scsi2 : SCSI emulation for USB Mass Storage devices
[ 152.059593] usbcore: registered new interface driver usb-storage
[ 152.060221] USB Mass Storage support registered.
[ 152.060971] usb-storage: device found at 2
[ 152.060984] usb-storage: waiting for device to settle before scanning
[ 157.057802] usb-storage: device scan complete
[ 157.061779] scsi 2:0:0:0: Direct-Access Kingston DataTraveler 2.0 1.02 PQ: 0 ANSI: 0 CCS
[ 157.259865] sd 2:0:0:0: [sdc] 251904 512-byte hardware sectors (129 MB)
[ 157.264056] sd 2:0:0:0: [sdc] Write Protect is off
[ 157.264077] sd 2:0:0:0: [sdc] Mode Sense: 23 00 00 00
[ 157.264084] sd 2:0:0:0: [sdc] Assuming drive cache: write through
[ 157.278063] sd 2:0:0:0: [sdc] 251904 512-byte hardware sectors (129 MB)
[ 157.280600] sd 2:0:0:0: [sdc] Write Protect is off
[ 157.280620] sd 2:0:0:0: [sdc] Mode Sense: 23 00 00 00
[ 157.280627] sd 2:0:0:0: [sdc] Assuming drive cache: write through
[ 157.280647] sdc: sdc1
[ 157.287972] sd 2:0:0:0: [sdc] Attached SCSI removable disk
[ 157.288079] sd 2:0:0:0: Attached scsi generic sg4 type 0
[ 219.390882] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
[ 219.390939] ata1.01: BMDMA stat 0x64
[ 219.390956] ata1.01: cmd ca/00:20:d8:c3:21/00:00:00:00:00/f4 tag 0 dma 16384 out
[ 219.390959] res 51/84:00:d8:c3:21/00:00:00:00:00/f4 Emask 0x10 (ATA bus error)
[ 219.390967] ata1.01: status: { DRDY ERR }
[ 219.390972] ata1.01: error: { ICRC ABRT }
[ 219.391026] ata1: soft resetting link
[ 219.707368] ata1.00: configured for UDMA/44
[ 219.723101] ata1.01: configured for UDMA/44
[ 219.723141] ata1: EH complete
[ 219.723850] sd 0:0:0:0: [sda] 40031712 512-byte hardware sectors (20496 MB)
[ 219.724542] sd 0:0:0:0: [sda] Write Protect is off
[ 219.724675] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 219.725545] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 219.866164] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
[ 219.866185] ata1.01: BMDMA stat 0x64
[ 219.866201] ata1.01: cmd ca/00:08:38:c3:45/00:00:00:00:00/f4 tag 0 dma 4096 out
[ 219.866205] res 51/84:00:38:c3:45/00:00:00:00:00/f4 Emask 0x10 (ATA bus error)
[ 219.866212] ata1.01: status: { DRDY ERR }
[ 219.866217] ata1.01: error: { ICRC ABRT }
[ 219.866271] ata1: soft resetting link
[ 220.123155] ata1.00: configured for UDMA/44
[ 220.138840] ata1.01: configured for UDMA/44
[ 220.138889] ata1: EH complete
[ 220.139718] sd 0:0:1:0: [sdb] 78165360 512-byte hardware sectors (40021 MB)
[ 220.139860] sd 0:0:1:0: [sdb] Write Protect is off
[ 220.139867] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 220.141282] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 220.142184] sd 0:0:0:0: [sda] 40031712 512-byte hardware sectors (20496 MB)
[ 220.143021] sd 0:0:0:0: [sda] Write Protect is off
[ 220.143032] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 220.143916] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 220.145200] sd 0:0:1:0: [sdb] 78165360 512-byte hardware sectors (40021 MB)
[ 220.145344] sd 0:0:1:0: [sdb] Write Protect is off
[ 220.145351] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 220.146726] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 408.704790] usb 1-2: new full speed USB device using uhci_hcd and address 2
[ 408.859905] usb 1-2: configuration #1 chosen from 1 choice
[ 409.011221] ndiswrapper version 1.52 loaded (smp=yes, preempt=no)
[ 409.180477] usb 1-2: reset full speed USB device using uhci_hcd and address 2
[ 409.392151] ndiswrapper: driver wnbusl51 (I-O DATA DEVICE,INC.,4/10/2003, 3.0.2) loaded
[ 410.864913] wlan0: ethernet device 00:a0:b0:49:9f:27 using NDIS driver: wnbusl51, version: 0x30002, NDIS version: 0x501, vendor: 'I-O DATA WN-B11/USBSL Wireless LAN Adapter', 04BB:0924.F.conf
[ 410.865011] BUG: unable to handle kernel paging request at virtual address e3e60728
[ 410.865022] printing eip: e0e35c65 *pde = 00000000
[ 410.865033] Oops: 0002 [#1] SMP
[ 410.865039] Modules linked in: ndiswrapper nls_iso8859_1 nls_cp437 usb_storage libusual binfmt_misc rfcomm l2cap bluetooth ipv6 ppdev cpufreq_stats cpufreq_conservative cpufreq_ondemand cpufreq_userspace freq_table cpufreq_powersave container video output dock sbs sbshc battery vfat fat ac pppoatm ppp_generic slhc lp snd_ens1371 gameport snd_ac97_codec ac97_bus snd_pcm_oss snd_mixer_oss snd_pcm evdev snd_seq_dummy serio_raw psmouse bt878 snd_seq_oss nvidia(P) tuner tea5767 tda8290 tuner_simple mt20xx pcspkr snd_seq_midi snd_rawmidi tea5761 snd_seq_midi_event button bttv ir_common snd_seq snd_timer compat_ioctl32 i2c_algo_bit i2c_viapro snd_seq_device videobuf_dma_sg videobuf_core btcx_risc tveeprom i2c_core via686a snd videodev v4l2_common v4l1_compat parport_pc via_agp soundcore parport shpchp agpgart snd_page_alloc pci_hotplug iptable_nat nf_nat nf_conntrack_ipv4 nf_conntrack iptable_mangle iptable_filter ip_tables x_tables ext3 jbd mbcache sg sr_mod cdrom sd_mod 8139too floppy uhci_hcd 8139cp mii usbcore pata_via ata_generic pata_acpi libata scsi_mod thermal processor fan fbcon tileblit font bitblit softcursor fuse
[ 410.865157]
[ 410.865165] Pid: 6039, comm: modprobe Tainted: P (2.6.24-19-generic #1)
[ 410.865172] EIP: 0060:[<e0e35c65>] EFLAGS: 00010297 CPU: 0
[ 410.865278] EIP is at NdisDispatchPnp+0xb35/0xfc0 [ndiswrapper]
[ 410.865284] EAX: 2d4e5720 EBX: de3c3c48 ECX: deee7800 EDX: 00000001
[ 410.865289] ESI: deee7800 EDI: de3c3c44 EBP: de843480 ESP: de3c3b6c
[ 410.865295] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[ 410.865302] Process modprobe (pid: 6039, ti=de3c2000 task=ded11140 task.ti=de3c2000)
[ 410.865307] Stack: deee7800 00000100 de3c3b54 de3c3b50 00000010 00000049 0000009f 00000027
[ 410.865319] e0e3c9bd dde91018 00030002 00000501 deee7800 deca919c 00000027 00000000
[ 410.865330] de843000 c140a4b4 00000287 e0e3c9bd dde91018 00000501 deca919c 00030002
[ 410.865341] Call Trace:
[ 410.865393] [<c012813d>] finish_task_switch+0x8d/0x90
[ 410.865428] [<c031aa7a>] schedule+0x20a/0x600
[ 410.865455] [<c012103d>] kunmap_atomic+0x3d/0xb0
[ 410.865469] [<c0172e8e>] get_page_from_freelist+0x29e/0x430
[ 410.865492] [<e0e2e521>] IoAllocateIrp+0x61/0x80 [ndiswrapper]
[ 410.865556] [<e0e2e815>] IofCallDriver+0x55/0xc0 [ndiswrapper]
[ 410.865606] [<e0e3385b>] IoSendIrpTopDev+0xbb/0x120 [ndiswrapper]
[ 410.865670] [<e0e33bb0>] pnp_start_device+0x50/0xb0 [ndiswrapper]
[ 410.865736] [<e0e33e4f>] wrap_pnp_start_device+0x23f/0x290 [ndiswrapper]
[ 410.865803] [<e0e34126>] wrap_pnp_start_usb_device+0xa6/0xd0 [ndiswrapper]
[ 410.865837] [<c01a5251>] find_inode+0x31/0x60
[ 410.865849] [<c01d70e0>] sysfs_ilookup_test+0x0/0x10
[ 410.865882] [<c01d779b>] sysfs_addrm_finish+0x4b/0x1c0
[ 410.865893] [<c01d7484>] sysfs_add_one+0x44/0xe0
[ 410.865905] [<c01d758d>] sysfs_addrm_start+0x6d/0xb0
[ 410.865915] [<c031b438>] mutex_lock+0x8/0x20
[ 410.865926] [<e087782b>] usb_autopm_do_device+0x7b/0x100 [usbcore]
[ 410.866024] [<e0877397>] usb_match_one_id+0x27/0xb0 [usbcore]
[ 410.866071] [<e08785d9>] usb_probe_interface+0xb9/0x140 [usbcore]
[ 410.866119] [<c02828a8>] driver_probe_device+0x88/0x190
[ 410.866140] [<c0215f30>] kobject_uevent_env+0xf0/0x3d0
[ 410.866170] [<c0282b1e>] __driver_attach+0x9e/0xa0
[ 410.866185] [<c0281cdb>] bus_for_each_dev+0x3b/0x60
[ 410.866207] [<c0282726>] driver_attach+0x16/0x20
[ 410.866215] [<c0282a80>] __driver_attach+0x0/0xa0
[ 410.866223] [<c028205a>] bus_add_driver+0x8a/0x1e0
[ 410.866247] [<e087811e>] usb_register_driver+0x8e/0x110 [usbcore]
[ 410.866295] [<e0e2340c>] loader_init+0x9c/0x140 [ndiswrapper]
[ 410.866330] [<e0e3023f>] wrap_procfs_init+0x3f/0xb0 [ndiswrapper]
[ 410.866364] [<e0e342f5>] wrapndis_init+0x45/0x50 [ndiswrapper]
[ 410.866402] [<e0a6a0b7>] wrapper_init+0xb7/0xc2 [ndiswrapper]
[ 410.866441] [<c01507c6>] sys_init_module+0x126/0x19c0
[ 410.866545] [<c0168c90>] disable_irq+0x0/0x30
[ 410.866587] [<c01043c2>] sysenter_past_esp+0x6b/0xa9
[ 410.866632] =======================
[ 410.866635] Code: ec ff ff 85 c0 0f 85 88 00 00 00 8b 54 24 60 c7 84 24 d8 00 00 00 00 00 00 00 8b 02 85 c0 74 34 31 d2 8b 4c 24 60 8b 44 91 04 90 <0f> ab 84 24 d8 00 00 00 83 c2 01 3b 11 72 e8 8b 84 24 d8 00 00
[ 410.866684] EIP: [<e0e35c65>] NdisDispatchPnp+0xb35/0xfc0 [ndiswrapper] SS:ESP 0068:de3c3b6c
[ 410.866726] ---[ end trace 2cd094c11aea708a ]---
[ 428.738008] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 433.743750] eth0: link down
[ 433.744326] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 433.775574] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 434.156693] ndiswrapper (iw_set_freq:334): setting configuration failed (C0010015)
[ 435.594690] NET: Registered protocol family 17
[ 458.901068] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 459.277563] ndiswrapper (iw_set_freq:334): setting configuration failed (C0010015)
[ 505.003009] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 515.848152] wlan0: no IPv6 routers present
[ 565.066909] ndiswrapper (iw_set_freq:334): setting configuration failed (C0010015)
[ 575.580157] wlan0: no IPv6 routers present
[ 755.971059] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
[ 755.971074] ata1.01: BMDMA stat 0x64
[ 755.971090] ata1.01: cmd ca/00:58:98:1e:3f/00:00:00:00:00/f3 tag 0 dma 45056 out
[ 755.971094] res 51/84:00:98:1e:3f/00:00:00:00:00/f3 Emask 0x10 (ATA bus error)
[ 755.971102] ata1.01: status: { DRDY ERR }
[ 755.971107] ata1.01: error: { ICRC ABRT }
[ 755.971170] ata1: soft resetting link
[ 756.176068] ata1.00: configured for UDMA/44
[ 756.191797] ata1.01: configured for UDMA/44
[ 756.191842] ata1: EH complete

[ 756.198792] sd 0:0:1:0: [sdb] Write Protect is off
[ 756.198798] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 756.198835] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

So it has worked fine before this kernel?
If so then when you installed this kernel did you also update ndiswrapper?
You might need to install the latest ndiswrapper for this kernel or there might be an issue with this kernel with USB hardware or something. You might look into getting the latest kernel from www.kernel.org and compiling that then recompile ndiswrapper to work with the new kernel and see if all is all right. Seen kernel 2.6.9 not work with some of my USB devices. The one before and all others after have worked fine. One can never tell what something new will bring.

Brian

thanks for your help. I got and recompiled the latest ndiswrapper version 1.53 but it seems things getting worse!! now the adapter isn't recongnized. I will return to 1.50 (version "suggested" by Package Manager) and i will cross my fingers!
Vi3da