Hi All,

Trying to install drivers for Highpoint Technology's RR2310 RAID card as a data drive. Following the simple instructions from HT seems to go well. Typeing

sudo sh .install.sh

returns:

The disk you insert is for linux kernel 2.6
Update initrd file /boot/initrd.img-2.6.28-11-generic for 2.6.28-11-generic
Please reboot the system to use the new driver module.

When I reboot things are as before: no array; the individual drives are fdisked as singles with no partition table.

When I check uname -r, I see the Ubuntu 9.04 kernel is 2.6.31-19-generic.
In /boot there are initrd files 2.6.28... 11, 15, 16, & 17 and 2.6.31... 16, 17, 19 & 22.

The card BIOS shows the array is 'NORMAL' and lspci shows it also

00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2)
00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3)
00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3)
00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1)
00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2)
00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1)
00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3)
00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3)
00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3)
00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2)
00:06.1 Audio device: nVidia Corporation MCP55 High Definition Audio (rev a2)
00:0a.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3)
00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3)
00:0e.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:06.0 VGA compatible controller: ATI Technologies Inc 3D Rage II+ 215GTB [Mach64 GTB] (rev 9a)
01:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10)
01:0b.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link)
02:00.0 SCSI storage controller: HighPoint Technologies, Inc. RocketRAID 2310 4 Port SATA-II Controller (rev 02)
03:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5751 Gigabit Ethernet PCI Express (rev 01)
04:00.0 SATA controller: JMicron Technology Corp. JMB362/JMB363 AHCI Controller (rev 03)
04:00.1 IDE interface: JMicron Technology Corp. JMB362/JMB363 AHCI Controller (rev 03)

I appreciate any and all help.
Thank you.

Did you do as beginning on page 53 of the manual, at http://www.highpoint-tech.com/PDF/RR...ser_Manual.pdfsays? The don't look "simple" to me!

Is this double-posted?

I'm only installing as a data drive ("...with Windows already installed") avoiding boot system drive.

I don't think I double posted.

Didn't get any answers till now so I reposted at Ubuntu forums? Anyway it turns out I had several kernels and it was loading the driver to the wrong kernel. ...just like it said.

Good! Glad you got the help needed.