LinuxQuestions.org

LinuxQuestions.org (/questions/)
-   Linux - Hardware (http://www.linuxquestions.org/questions/linux-hardware-18/)
-   -   Unable to boot from any LiveCD, some DVD drive error messages (http://www.linuxquestions.org/questions/linux-hardware-18/unable-to-boot-from-any-livecd-some-dvd-drive-error-messages-722088/)

raqua 04-27-2009 04:42 PM

[Solved] Unable to boot from any LiveCD, some DVD drive error messages
 
Hello.

I recently installed new DVD drive to my PC. The old one broke and went back to store. Before that, everything was working just fine. I have currently 4 systems installed on the PC.

1) Arch Linux (my main system)
2) Ubuntu 8.04
3) Edubuntu 7.10
4) Windows XP XP3

It is not my main machine, it is used as backup server/test machine. All the systems on this PC were installed using old drive.
Since I installed new one, I can not boot any live cd on that system with the exception of arch linux install cd. At least from those systems I tried (various versions of Ubuntu, Fedora, Mint).
I always end up with initramfs shell and keyboard (USB connected) not working. Before dropping to this shell, system tries to mount root file system. Fedora says, that it was unable to mount root filesystem.
Googling revealed a lot of similar problems, but usually with existing installations, not while using live cd.

All installed systems on that PC boot just fine, but I noticed, that Arch started to give me some errors while booting kernel. They are releated to optical drive. See ata2 section on my dmesg:

Code:

Linux version 2.6.26-ARCH (root@T-POWA-LX) (gcc version 4.3.2 (GCC) ) #1 SMP PREEMPT Tue Sep 9 10:15:21 UTC 2008
PAT disabled. Not yet verified on this CPU type.
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 0000000047ff0000 (usable)
 BIOS-e820: 0000000047ff0000 - 0000000047ff3000 (ACPI NVS)
 BIOS-e820: 0000000047ff3000 - 0000000048000000 (ACPI data)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
255MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at [c00f5610] 000f5610
Entering add_active_range(0, 0, 294896) 0 entries of 256 used
Zone PFN ranges:
  DMA            0 ->    4096
  Normal      4096 ->  229376
  HighMem    229376 ->  294896
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->  294896
On node 0 totalpages: 294896
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 1760 pages used for memmap
  Normal zone: 223520 pages, LIFO batch:31
  HighMem zone: 512 pages used for memmap
  HighMem zone: 65008 pages, LIFO batch:15
  Movable zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP 000F6F60, 0014 (r0 VIA694)
ACPI: RSDT 47FF3000, 002C (r1 VIA694 AWRDACPI 42302E31 AWRD        0)
ACPI: FACP 47FF3040, 0074 (r1 VIA694 AWRDACPI 42302E31 AWRD        0)
ACPI: DSDT 47FF30C0, 25CA (r1 VIA694 AWRDACPI    1000 MSFT  100000C)
ACPI: FACS 47FF0000, 0040
ACPI: APIC 47FF56C0, 005C (r1 VIA694                0            0)
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 5 global_irq 5 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ5 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 48000000:b6c00000)
PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 39464 bytes of per cpu data
NR_CPUS: 16, nr_cpu_ids: 2
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 292592
Kernel command line: root=/dev/disk/by-uuid/5c16bd67-b488-4790-882a-a0203cae2297 ro
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 910.340 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1164096k/1179584k available (2120k kernel code, 14668k reserved, 744k data, 264k init, 262080k highmem)
virtual kernel memory layout:
    fixmap  : 0xffee4000 - 0xfffff000  (1132 kB)
    pkmap  : 0xff800000 - 0xffc00000  (4096 kB)
    vmalloc : 0xf8800000 - 0xff7fe000  ( 111 MB)
    lowmem  : 0xc0000000 - 0xf8000000  ( 896 MB)
      .init : 0xc03d3000 - 0xc0415000  ( 264 kB)
      .data : 0xc031225e - 0xc03cc380  ( 744 kB)
      .text : 0xc0100000 - 0xc031225e  (2120 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Calibrating delay using timer specific routine.. 1823.35 BogoMIPS (lpj=3037365)
Security Framework initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU serial number disabled.
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20080321
ACPI: Checking initramfs for custom DSDT
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel Pentium III (Coppermine) stepping 0a
Booting processor 1/1 ip 6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 1821.36 BogoMIPS (lpj=3034176)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU serial number disabled.
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Pentium III (Coppermine) stepping 0a
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (3644.71 BogoMIPS).
net_namespace: 652 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb370, last bus=1
PCI: Using configuration type 1 for base access
Setting up standard PCI resources
mtrr: your CPUs had inconsistent variable MTRR settings
mtrr: probably your BIOS does not setup all CPUs.
mtrr: corrected configuration.
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:07.4: quirk: region 6000-607f claimed by vt82c686 HW-mon
pci 0000:00:07.4: quirk: region 5000-500f claimed by vt82c686 SMB
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Handling Garbled _PRT entry
ACPI: Handling Garbled _PRT entry
ACPI: Handling Garbled _PRT entry
ACPI: Handling Garbled _PRT entry
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
system 00:00: iomem range 0xcc000-0xcffff has been reserved
system 00:00: iomem range 0xd0800-0xd3fff has been reserved
system 00:00: iomem range 0xf0000-0xfbfff could not be reserved
system 00:00: iomem range 0xfc000-0xfffff could not be reserved
system 00:00: iomem range 0x47ff0000-0x47ffffff could not be reserved
system 00:00: iomem range 0xffff0000-0xffffffff could not be reserved
system 00:00: iomem range 0x0-0x9ffff could not be reserved
system 00:00: iomem range 0x100000-0x47feffff could not be reserved
system 00:00: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:00: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:02: ioport range 0x4d0-0x4d1 has been reserved
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: 0xd6000000-0xd7ffffff
  PREFETCH window: 0x00000000d4000000-0x00000000d5ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Unpacking initramfs... done
Freeing initrd memory: 508k freed
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1763
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: VIA PCI bridge detected.Disabling DAC.
pci 0000:00:07.0: Enabling VIA external APIC routing
pci 0000:01:00.0: Boot video device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
input: Macintosh mouse button emulation as /class/input/input0
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 264k freed
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
No dock devices found.
SCSI subsystem initialized
libata version 3.00 loaded.
pata_via 0000:00:07.1: version 0.3.3
scsi0 : pata_via
scsi1 : pata_via
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xd000 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xd008 irq 15
ata1.00: ATA-7: ST3120814A, 3.AAD, max UDMA/100
ata1.00: 234441648 sectors, multi 16: LBA48
ata1.00: configured for UDMA/100
ata2.00: ATAPI: PIONEER DVD-RW  DVR-108, 1.20, max UDMA/66
ata2.00: configured for UDMA/66
scsi 0:0:0:0: Direct-Access    ATA      ST3120814A      3.AA PQ: 0 ANSI: 5
ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.00: cmd a0/01:00:00:60:00/00:00:00:00:00/a0 tag 0 dma 96 in
        cdb 12 00 00 00 60 00 00 00  00 00 00 00 00 00 00 00
        res 40/00:02:24:24:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata2.00: status: { DRDY }
ata2: soft resetting link
ata2.00: configured for UDMA/66
ata2: EH complete
ata2.00: limiting speed to UDMA/44:PIO4
ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.00: cmd a0/01:00:00:60:00/00:00:00:00:00/a0 tag 0 dma 96 in
        cdb 12 00 00 00 60 00 00 00  00 00 00 00 00 00 00 00
        res 40/00:02:24:24:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata2.00: status: { DRDY }
ata2: soft resetting link
ata2.00: configured for UDMA/44
ata2: EH complete
ata2.00: limiting speed to UDMA/33:PIO4
ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.00: cmd a0/01:00:00:60:00/00:00:00:00:00/a0 tag 0 dma 96 in
        cdb 12 00 00 00 60 00 00 00  00 00 00 00 00 00 00 00
        res 40/00:02:24:24:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata2.00: status: { DRDY }
ata2: soft resetting link
ata2.00: configured for UDMA/33
ata2: EH complete
ata2.00: limiting speed to PIO4
ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.00: cmd a0/01:00:00:60:00/00:00:00:00:00/a0 tag 0 dma 96 in
        cdb 12 00 00 00 60 00 00 00  00 00 00 00 00 00 00 00
        res 40/00:02:24:24:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata2.00: status: { DRDY }
ata2: soft resetting link
ata2.00: configured for PIO4
scsi scan: 96 byte inquiry failed.  Consider BLIST_INQUIRY_36 for this device
ata2: EH complete
scsi 1:0:0:0: CD-ROM            PIONEER  DVD-RW  DVR-108  1.20 PQ: 0 ANSI: 5
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda:<4>Driver 'sr' needs updating - please use bus_type methods
 sda1 sda2 sda3 < sda5 sda6 sda7 sda8 sda9 sda10 >
sd 0:0:0:0: [sda] Attached SCSI disk
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, y3k
udev: starting version 141
udev: deprecated sysfs layout; update the kernel or disable CONFIG_SYSFS_DEPRECATED; some udev features will not work correctly
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
usbcore: registered new interface driver rt73usb
ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 19 (level, low) -> IRQ 19
3c59x: Donald Becker and others.
0000:00:0c.0: 3Com PCI 3c905C Tornado at f8904000.
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 17
loop: module loaded
input: Power Button (FF) as /class/input/input1
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input2
ACPI: Power Button (CM) [PWRB]
ACPI: ACPI0007:00 is registered as cooling_device0
ACPI: ACPI0007:01 is registered as cooling_device1
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
parport_pc: VIA parallel port: io=0x378, irq=7
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Linux agpgart interface v0.103
agpgart: Detected VIA Apollo Pro 133 chipset
agpgart: AGP aperture is 64M @ 0xd0000000
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5
ACPI: PCI Interrupt 0000:00:0b.2[C] -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:0b.2: EHCI Host Controller
ehci_hcd 0000:00:0b.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0b.2: irq 19, io mem 0xd9001000
ehci_hcd 0000:00:0b.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
input: PC Speaker as /class/input/input3
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:07.2: irq 11, io base 0x0000d400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:07.3[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:07.3: UHCI Host Controller
uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:07.3: irq 11, io base 0x0000d800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
usb 1-2: new high speed USB device using ehci_hcd and address 2
ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 17 (level, low) -> IRQ 17
ohci_hcd 0000:00:0b.0: OHCI Host Controller
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:0b.0: irq 17, io mem 0xd9003000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 3 ports detected
usb 1-2: configuration #1 chosen from 1 choice
ACPI: PCI Interrupt 0000:00:0b.1[B] -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:00:0b.1: OHCI Host Controller
ohci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 5
ohci_hcd 0000:00:0b.1: irq 16, io mem 0xd9000000
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 2-1: new low speed USB device using uhci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
ppdev: user-space parallel port driver
lp0: using parport0 (interrupt-driven).
usb 2-2: new low speed USB device using uhci_hcd and address 3
usb 2-2: configuration #1 chosen from 1 choice
usb 1-2: reset high speed USB device using ehci_hcd and address 2
phy0: Selected rate control algorithm 'pid'
zd1211rw 1-2:1.0: phy0
usbcore: registered new interface driver zd1211rw
usbcore: registered new interface driver hiddev
input: HID 04d9:1203 as /class/input/input4
input,hidraw0: USB HID v1.11 Keyboard [HID 04d9:1203] on usb-0000:00:07.2-1
input: HID 04d9:1203 as /class/input/input5
input,hidraw1: USB HID v1.11 Device [HID 04d9:1203] on usb-0000:00:07.2-1
input: Genius Optical Mouse as /class/input/input6
input,hidraw2: USB HID v1.10 Mouse [Genius Optical Mouse] on usb-0000:00:07.2-2
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
EXT3 FS on sda6, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 1951856k swap on /dev/sda10.  Priority:-1 extents:1 across:1951856k
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
ClusterIP Version 0.8 loaded successfully
firmware: requesting zd1211/zd1211b_ub
firmware: requesting zd1211/zd1211b_uphr
zd1211rw 1-2:1.0: firmware version 4725
zd1211rw 1-2:1.0: zd1211b chip 0586:3410 v4810 high 00-19-cb AL2230_RF pa0 g--NS
eth0:  setting half-duplex.
wlan0: Initial auth_alg=0
wlan0: authenticate with AP 00:1c:f0:ff:b7:50
wlan0: RX authentication from 00:1c:f0:ff:b7:50 (alg=0 transaction=2 status=0)
wlan0: authenticated
wlan0: associate with AP 00:1c:f0:ff:b7:50
wlan0: RX AssocResp from 00:1c:f0:ff:b7:50 (capab=0x431 status=0 aid=1)
wlan0: associated
wlan0: switched to short barker preamble (BSSID=00:1c:f0:ff:b7:50)
padlock: VIA PadLock not detected.
martian source 255.255.255.255 from 192.168.1.1, on dev wlan0
ll header: ff:ff:ff:ff:ff:ff:00:1c:f0:ff:b7:50:08:00
martian source 255.255.255.255 from 192.168.1.1, on dev wlan0
ll header: ff:ff:ff:ff:ff:ff:00:1c:f0:ff:b7:50:08:00


I tried to remove that drive and attached another one, but got the same result. I also tried to change the connecting cable, but it did not help.
I am running out of ideas here ...


lspci:
Code:

00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4)
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP]
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 16)
00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 16)
00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
00:0a.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
00:0b.0 USB Controller: NEC Corporation USB (rev 43)
00:0b.1 USB Controller: NEC Corporation USB (rev 43)
00:0b.2 USB Controller: NEC Corporation USB 2.0 (rev 04)
00:0c.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78)
01:00.0 VGA compatible controller: nVidia Corporation NV5M64 [RIVA TNT2 Model 64/Model 64 Pro] (rev 15)

Thanks in advance.
Raqua

linus72 04-27-2009 05:09 PM

Did you change/check either the /etc/fstab, /etc/mtab on any of them?

raqua 04-28-2009 12:47 AM

No I did not change any of them. But this problem is happening very soon in kernel booting sequence, I think it does not matter what is in fstab or mtab at that time.
And my main problem remains unable to boot live cd, where this should not matter at all.

onebuck 04-28-2009 10:12 AM

Hi,

Do you have the drives setup with 'CS' on that channel? How did you setup the jumper for the new 'DVD' drive?

raqua 04-28-2009 05:20 PM

Drive's jumper is set to master and recognized as master by BIOS. Secondary master - on primary controller are two HDDs.

onebuck 04-29-2009 07:14 AM

Hi,

At boot pass the parameter 'noprobe=ata2' to the kernel. Post the output of 'dmesg'.

BTW, the current 'dmesg' shows the hdd on 'ata1'. Right?

How do you have your scsi/usb setup in BIOS?

raqua 04-30-2009 02:15 PM

noprobe=ata2 on live cd resulted in the same behaviour as I described before. No boot.

Booting the installed distro with noprobe=ata2 resulted in this dmesg - the sam errors as before show up, but boots fine.

Code:

Linux version 2.6.26-ARCH (root@T-POWA-LX) (gcc version 4.3.2 (GCC) ) #1 SMP PREEMPT Tue Sep 9 10:15:21 UTC 2008
PAT disabled. Not yet verified on this CPU type.
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 0000000047ff0000 (usable)
 BIOS-e820: 0000000047ff0000 - 0000000047ff3000 (ACPI NVS)
 BIOS-e820: 0000000047ff3000 - 0000000048000000 (ACPI data)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
255MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at [c00f5610] 000f5610
Entering add_active_range(0, 0, 294896) 0 entries of 256 used
Zone PFN ranges:
  DMA            0 ->    4096
  Normal      4096 ->  229376
  HighMem    229376 ->  294896
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->  294896
On node 0 totalpages: 294896
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 1760 pages used for memmap
  Normal zone: 223520 pages, LIFO batch:31
  HighMem zone: 512 pages used for memmap
  HighMem zone: 65008 pages, LIFO batch:15
  Movable zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP 000F6F60, 0014 (r0 VIA694)
ACPI: RSDT 47FF3000, 002C (r1 VIA694 AWRDACPI 42302E31 AWRD        0)
ACPI: FACP 47FF3040, 0074 (r1 VIA694 AWRDACPI 42302E31 AWRD        0)
ACPI: DSDT 47FF30C0, 25CA (r1 VIA694 AWRDACPI    1000 MSFT  100000C)
ACPI: FACS 47FF0000, 0040
ACPI: APIC 47FF56C0, 005C (r1 VIA694                0            0)
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 5 global_irq 5 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ5 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 48000000:b6c00000)
PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 39464 bytes of per cpu data
NR_CPUS: 16, nr_cpu_ids: 2
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 292592
Kernel command line: root=/dev/disk/by-uuid/5c16bd67-b488-4790-882a-a0203cae2297 ro noprobe=ata2
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 910.333 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1164096k/1179584k available (2120k kernel code, 14668k reserved, 744k data, 264k init, 262080k highmem)
virtual kernel memory layout:
    fixmap  : 0xffee4000 - 0xfffff000  (1132 kB)
    pkmap  : 0xff800000 - 0xffc00000  (4096 kB)
    vmalloc : 0xf8800000 - 0xff7fe000  ( 111 MB)
    lowmem  : 0xc0000000 - 0xf8000000  ( 896 MB)
      .init : 0xc03d3000 - 0xc0415000  ( 264 kB)
      .data : 0xc031225e - 0xc03cc380  ( 744 kB)
      .text : 0xc0100000 - 0xc031225e  (2120 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Calibrating delay using timer specific routine.. 1823.32 BogoMIPS (lpj=3037323)
Security Framework initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU serial number disabled.
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20080321
ACPI: Checking initramfs for custom DSDT
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel Pentium III (Coppermine) stepping 0a
Booting processor 1/1 ip 6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 1821.42 BogoMIPS (lpj=3034284)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU serial number disabled.
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Pentium III (Coppermine) stepping 0a
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (3644.75 BogoMIPS).
net_namespace: 652 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb370, last bus=1
PCI: Using configuration type 1 for base access
Setting up standard PCI resources
mtrr: your CPUs had inconsistent variable MTRR settings
mtrr: probably your BIOS does not setup all CPUs.
mtrr: corrected configuration.
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:07.4: quirk: region 6000-607f claimed by vt82c686 HW-mon
pci 0000:00:07.4: quirk: region 5000-500f claimed by vt82c686 SMB
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Handling Garbled _PRT entry
ACPI: Handling Garbled _PRT entry
ACPI: Handling Garbled _PRT entry
ACPI: Handling Garbled _PRT entry
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
system 00:00: iomem range 0xcc000-0xcffff has been reserved
system 00:00: iomem range 0xd0800-0xd3fff has been reserved
system 00:00: iomem range 0xf0000-0xfbfff could not be reserved
system 00:00: iomem range 0xfc000-0xfffff could not be reserved
system 00:00: iomem range 0x47ff0000-0x47ffffff could not be reserved
system 00:00: iomem range 0xffff0000-0xffffffff could not be reserved
system 00:00: iomem range 0x0-0x9ffff could not be reserved
system 00:00: iomem range 0x100000-0x47feffff could not be reserved
system 00:00: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:00: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:02: ioport range 0x4d0-0x4d1 has been reserved
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: 0xd6000000-0xd7ffffff
  PREFETCH window: 0x00000000d4000000-0x00000000d5ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Unpacking initramfs... done
Freeing initrd memory: 508k freed
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1763
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: VIA PCI bridge detected.Disabling DAC.
pci 0000:00:07.0: Enabling VIA external APIC routing
pci 0000:01:00.0: Boot video device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
input: Macintosh mouse button emulation as /class/input/input0
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 264k freed
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
No dock devices found.
SCSI subsystem initialized
libata version 3.00 loaded.
pata_via 0000:00:07.1: version 0.3.3
scsi0 : pata_via
scsi1 : pata_via
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xd000 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xd008 irq 15
ata1.00: ATA-7: ST3120814A, 3.AAD, max UDMA/100
ata1.00: 234441648 sectors, multi 16: LBA48
ata1.01: ATA-6: WDC WD2000JB-00FUA0, 15.05R15, max UDMA/100
ata1.01: 390721968 sectors, multi 16: LBA48
ata1.00: configured for UDMA/100
ata1.01: configured for UDMA/100
ata2.00: ATAPI: PIONEER DVD-RW  DVR-108, 1.20, max UDMA/33
ata2.00: configured for UDMA/33
scsi 0:0:0:0: Direct-Access    ATA      ST3120814A      3.AA PQ: 0 ANSI: 5
scsi 0:0:1:0: Direct-Access    ATA      WDC WD2000JB-00F 15.0 PQ: 0 ANSI: 5
ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.00: cmd a0/01:00:00:60:00/00:00:00:00:00/a0 tag 0 dma 96 in
        cdb 12 00 00 00 60 00 00 00  00 00 00 00 00 00 00 00
        res 40/00:02:24:24:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata2.00: status: { DRDY }
ata2: soft resetting link
ata2.00: configured for UDMA/33
ata2: EH complete
ata2.00: limiting speed to UDMA/25:PIO4
ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.00: cmd a0/01:00:00:60:00/00:00:00:00:00/a0 tag 0 dma 96 in
        cdb 12 00 00 00 60 00 00 00  00 00 00 00 00 00 00 00
        res 40/00:02:24:24:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata2.00: status: { DRDY }
ata2: soft resetting link
ata2.00: configured for UDMA/25
ata2: EH complete
ata2.00: limiting speed to PIO4
ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata2.00: cmd a0/01:00:00:60:00/00:00:00:00:00/a0 tag 0 dma 96 in
        cdb 12 00 00 00 60 00 00 00  00 00 00 00 00 00 00 00
        res 40/00:02:24:24:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata2.00: status: { DRDY }
ata2: soft resetting link
ata2.00: configured for PIO4
ata2: EH complete
scsi 1:0:0:0: CD-ROM            PIONEER  DVD-RW  DVR-108  1.20 PQ: 0 ANSI: 5
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda:<4>Driver 'sr' needs updating - please use bus_type methods
 sda1 sda2 sda3 < sda5 sda6 sda7 sda8 sda9 sda10 >
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:1:0: [sdb] 390721968 512-byte hardware sectors (200050 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sdb] 390721968 512-byte hardware sectors (200050 MB)
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdb: sdb2 < sdb5 >
sd 0:0:1:0: [sdb] Attached SCSI disk
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, y3k
udev: starting version 141
udev: deprecated sysfs layout; update the kernel or disable CONFIG_SYSFS_DEPRECATED; some udev features will not work correctly
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
usbcore: registered new interface driver rt73usb
ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 19 (level, low) -> IRQ 19
3c59x: Donald Becker and others.
0000:00:0c.0: 3Com PCI 3c905C Tornado at f8904000.
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 17
loop: module loaded
input: Power Button (FF) as /class/input/input1
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input2
ACPI: Power Button (CM) [PWRB]
ACPI: ACPI0007:00 is registered as cooling_device0
ACPI: ACPI0007:01 is registered as cooling_device1
Linux agpgart interface v0.103
agpgart: Detected VIA Apollo Pro 133 chipset
agpgart: AGP aperture is 64M @ 0xd0000000
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:1:0: Attached scsi generic sg1 type 0
sr 1:0:0:0: Attached scsi generic sg2 type 5
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
parport_pc: VIA parallel port: io=0x378, irq=7
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: PCI Interrupt 0000:00:0b.2[C] -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:0b.2: EHCI Host Controller
ehci_hcd 0000:00:0b.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0b.2: irq 19, io mem 0xd9001000
ehci_hcd 0000:00:0b.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:07.2: irq 11, io base 0x0000d400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt 0000:00:07.3[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:07.3: UHCI Host Controller
uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:07.3: irq 11, io base 0x0000d800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-2: new high speed USB device using ehci_hcd and address 2
ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 17 (level, low) -> IRQ 17
ohci_hcd 0000:00:0b.0: OHCI Host Controller
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:0b.0: irq 17, io mem 0xd9003000
usb 1-2: configuration #1 chosen from 1 choice
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 3 ports detected
ACPI: PCI Interrupt 0000:00:0b.1[B] -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:00:0b.1: OHCI Host Controller
ohci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 5
ohci_hcd 0000:00:0b.1: irq 16, io mem 0xd9000000
usb 2-1: new low speed USB device using uhci_hcd and address 2
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
input: PC Speaker as /class/input/input3
usb 2-1: configuration #1 chosen from 1 choice
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
usb 2-2: new low speed USB device using uhci_hcd and address 3
usb 2-2: configuration #1 chosen from 1 choice
usb 1-2: reset high speed USB device using ehci_hcd and address 2
phy0: Selected rate control algorithm 'pid'
zd1211rw 1-2:1.0: phy0
usbcore: registered new interface driver zd1211rw
usbcore: registered new interface driver hiddev
input: HID 04d9:1203 as /class/input/input4
input,hidraw0: USB HID v1.11 Keyboard [HID 04d9:1203] on usb-0000:00:07.2-1
input: HID 04d9:1203 as /class/input/input5
input,hidraw1: USB HID v1.11 Device [HID 04d9:1203] on usb-0000:00:07.2-1
input: Genius Optical Mouse as /class/input/input6
input,hidraw2: USB HID v1.10 Mouse [Genius Optical Mouse] on usb-0000:00:07.2-2
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
EXT3 FS on sda6, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 1951856k swap on /dev/sda10.  Priority:-1 extents:1 across:1951856k
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
ClusterIP Version 0.8 loaded successfully
firmware: requesting zd1211/zd1211b_ub
firmware: requesting zd1211/zd1211b_uphr
zd1211rw 1-2:1.0: firmware version 4725
zd1211rw 1-2:1.0: zd1211b chip 0586:3410 v4810 high 00-19-cb AL2230_RF pa0 g--NS
eth0:  setting half-duplex.
wlan0: Initial auth_alg=0
wlan0: authenticate with AP 00:1c:f0:ff:b7:50
wlan0: RX authentication from 00:1c:f0:ff:b7:50 (alg=0 transaction=2 status=0)
wlan0: authenticated
wlan0: associate with AP 00:1c:f0:ff:b7:50
wlan0: RX AssocResp from 00:1c:f0:ff:b7:50 (capab=0x431 status=0 aid=1)
wlan0: associated
wlan0: switched to short barker preamble (BSSID=00:1c:f0:ff:b7:50)
padlock: VIA PadLock not detected.
martian source 255.255.255.255 from 192.168.1.1, on dev wlan0
ll header: ff:ff:ff:ff:ff:ff:00:1c:f0:ff:b7:50:08:00
martian source 255.255.255.255 from 192.168.1.1, on dev wlan0
ll header: ff:ff:ff:ff:ff:ff:00:1c:f0:ff:b7:50:08:00

So noprobe seems to have no effect on the systems behaviour.
There are two disks on ata1. I tried to disconnect them, switch the cable, connect DVD drives to ata1 instead ata2 - no change in booting live cd result. :/
USB is enabled and I also have additional PCI USB card. ATA 100 RAID is disabled and SCSI is not present on my system.

raqua 05-04-2009 04:51 AM

I solved this problem by adding kernel boot parameter pci=noacpi.


All times are GMT -5. The time now is 01:19 AM.