LinuxQuestions.org
Support LQ: Use code LQ3 and save $3 on Domain Registration
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Hardware
User Name
Password
Linux - Hardware This forum is for Hardware issues.
Having trouble installing a piece of hardware? Want to know if that peripheral is compatible with Linux?

Notices

Reply
 
Search this Thread
Old 02-05-2006, 03:34 AM   #1
suhis
Member
 
Registered: Dec 2003
Distribution: Suse 8.2
Posts: 48

Rep: Reputation: 15
two sound cards not working (extigy(usb) and integrated)


Hi, I have two sound cards. one is creative extigy and its usb and another one is integrated something.. I can't turn off this integrated sound card from bios and i don't care if it works or not. i want to get this usb sound card working.
When i start this extigy my suse 10.0 founds it and it appears to kmix.. it also appears to xmms alsa, but when i try to play something from xmms it says 'Please check that: Your soundcard is configure properly, You have the correct output plugin selected, No other program is blocking the soundcard.' If i try to use amarok it says that 'xine was unable to initialize any audio-drivers.'. I have tried to install it in yast. I have also tried to run alsaconf but it doesn't find it .. it only finds my integrated sound card and i think this problem is because i have two sound cards and they can't handle each other.

ps. sorry for bad english


and now i'll paste some information

uname -r
Quote:
2.6.13-15.7-default
dmesg
[HTML]Linux version 2.6.13-15.7-default (geeko@buildhost) (gcc version 4.0.2 20050901 (prerelease) (SUSE Linux)) #1 Tue Nov 29 14:32:29 UTC 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fcf0000 (usable)
BIOS-e820: 000000001fcf0000 - 000000001fcff000 (ACPI data)
BIOS-e820: 000000001fcff000 - 000000001fd00000 (ACPI NVS)
BIOS-e820: 000000001fd00000 - 000000001fe00000 (usable)
BIOS-e820: 000000001fe00000 - 0000000020000000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
510MB LOWMEM available.
On node 0 totalpages: 130560
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126464 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 HTCLTD ) @ 0x000f62e0
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x1fcfb1c9
ACPI: FADT (v001 Wistro H2U 0x06040000 PTL 0x000f4240) @ 0x1fcfef64
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x1fcfefd8
ACPI: DSDT (v001 WIST H2U 0x06040000 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x8008
ACPI: local apic disabled
Allocating PCI resources starting at 20000000 (gap: 20000000:dff80000)
Built 1 zonelists
Kernel command line: root=/dev/hda4 vga=0x317 selinux=0 resume=/dev/hda3 splash=silent
bootsplash: silent mode.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 2523.346 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 511832k/522240k available (2029k kernel code, 9680k reserved, 695k data, 204k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 5050.65 BogoMIPS (lpj=10101302)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 3febf9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 3febf9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: 3febf9ff 00000000 00000000 00000080 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
mtrr: v2.0 (20020519)
CPU: Intel(R) Pentium(R) 4 CPU 2.53GHz stepping 04
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
checking if image is initramfs... it is
Freeing initrd memory: 1816k freed
ACPI: Looking for DSDT in initrd... not found!
not found!
ACPI: setting ELCR to 0200 (from 0800)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd749, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20050408
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
Uncovering SIS962 that hid as a SIS503 (compatible=1)
Enabling SiS 96x SMBus.
PCI: Ignoring BAR0-3 of IDE controller 0000:00:02.5
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 4 5 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 4 5 7 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 4 5 7 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 4 5 7 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 4 5 7 10 *11)
ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 7 10 *11)
ACPI: PCI Interrupt Link [LNKG] (IRQs 4 5 7 10 *11)
ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 7 10 *11)
ACPI: Embedded Controller [EC] (gpe 30)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
pnp: 00:03: ioport range 0x8000-0x80fe could not be reserved
pnp: 00:03: ioport range 0x9000-0x907f could not be reserved
pnp: 00:03: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:03: ioport range 0xfe00-0xfe00 has been reserved
PCI: Bridge: 0000:00:01.0
IO window: a000-afff
MEM window: ec100000-ec1fffff
PREFETCH window: f0000000-f7ffffff
PCI: Bus 2, cardbus bridge: 0000:00:09.0
IO window: 00003000-00003fff
IO window: 00004000-00004fff
PREFETCH window: 20000000-21ffffff
MEM window: 22000000-23ffffff
PCI: Bus 6, cardbus bridge: 0000:00:09.1
IO window: 00005000-00005fff
IO window: 00006000-00006fff
PREFETCH window: 24000000-25ffffff
MEM window: 26000000-27ffffff
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:09.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
Simple Boot Flag at 0x35 set to 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1139134826.252:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
vesafb: framebuffer at 0xf0000000, mapped to 0xe0880000, using 6144k, total 65536k
vesafb: mode is 1024x768x16, linelength=2048, pages=41
vesafb: protected mode interface info at c000:548f
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 109235 bytes,<6>...found (1024x768, 47024 bytes, v3).
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A
ACPI-0212: *** Warning: Device is not power manageable
PCI: Enabling device 0000:00:02.6 (0000 -> 0001)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:02.6[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt for device 0000:00:02.6 disabled
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
loop: loaded (max 8 devices)
mice: PS/2 mouse device common for all mice
input: PC Speaker
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 3.38
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
Using IPI Shortcut mode
ACPI wakeup devices:
SLP2 LID BAT0 MDM SLAN
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 204k freed
input: AT Translated Set 2 keyboard on isa0060/serio0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 0000:00:02.5
ACPI: PCI Interrupt 0000:00:02.5[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
SIS5513: chipset revision 0
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
ide0: BM-DMA at 0x1000-0x1007, BIOS settings: hdaMA, hdbio
ide1: BM-DMA at 0x1008-0x100f, BIOS settings: hdcMA, hddio
Probing IDE interface ide0...
hda: IC25N030ATCS04-0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 58605120 sectors (30005 MB) w/1768KiB Cache, CHS=58140/16/63, UDMA(100)
hda: cache flushes not supported
hda: hda1 hda2 hda3 hda4
Probing IDE interface ide1...
hdc: QSI CD-RW/DVD-ROM SBW242C, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Synaptics Touchpad, model: 1, fw: 5.8, id: 0x9248b1, caps: 0x904713/0x4000
input: SynPS/2 Synaptics TouchPad on isa0060/serio4
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Thermal Zone [THRS] (26 C)
ACPI: Thermal Zone [THRC] (36 C)
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Attempting manual resume
swsusp: Suspend partition has wrong signature?
ReiserFS: hda4: found reiserfs format "3.6" with standard journal
ReiserFS: hda4: using ordered data mode
ReiserFS: hda4: journal params: device hda4, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda4: checking transaction log (hda4)
ReiserFS: hda4: Using r5 hash to sort names
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
Adding 248996k swap on /dev/hda3. Priority:-1 extents:1
usbcore: registered new driver usbfs
usbcore: registered new driver hub
usbcore: registered new driver snd-usb-audio
zd1211: module not supported by Novell, setting U taint flag.
zd1211 - http://zd1211.ath.cx/
Based on www.zydas.com.tw driver version 2.0.0.0
usbcore: registered new driver zd1211
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected SiS 646 chipset
agpgart: AGP aperture is 64M @ 0xe8000000
i2c-sis96x version 1.0.0
sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x9000
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKE] -> GSI 11 (level, low) -> IRQ 11
ohci_hcd 0000:00:03.0: OHCI Host Controller
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:03.0: irq 11, io mem 0xec001000
PCI: Enabling device 0000:00:02.7 (0000 -> 0001)
ACPI: PCI Interrupt 0000:00:02.7[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:03.1[B] -> Link [LNKF] -> GSI 11 (level, low) -> IRQ 11
ohci_hcd 0000:00:03.1: OHCI Host Controller
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:03.1: irq 11, io mem 0xec002000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:03.2[C] -> Link [LNKG] -> GSI 11 (level, low) -> IRQ 11
ohci_hcd 0000:00:03.2: OHCI Host Controller
ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:03.2: irq 11, io mem 0xec003000
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1299 $ Ben Collins <bcollins@debian.org>
ACPI: PCI Interrupt 0000:00:02.3[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
ohci1394: fw-host0: Unexpected PCI resource length of 1000!
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[11] MMIO=[ec000000-ec0007ff] Max Packet=[2048]
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 2-2: new low speed USB device using ohci_hcd and address 2
sis900.c: v1.08.08 Jan. 22 2005
usb 3-1: new full speed USB device using ohci_hcd and address 2
hub 3-1:1.0: USB hub found
hub 3-1:1.0: 4 ports detected
usb 3-1.3: new full speed USB device using ohci_hcd and address 3
Release Ver = 4721
EEPORM Ver = 4330
PA type: 0
intel8x0_measure_ac97_clock: measured 55423 usecs
intel8x0: clocking to 48000
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:00:09.0 [17c0:3202]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:09.0, mfunc 0x01001022, devctl 0x44
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:03.3[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:03.3: EHCI Host Controller
ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:03.3: irq 11, io mem 0xec004000
PCI: cache line size of 128 is not supported by device 0000:00:03.3
ehci_hcd 0000:00:03.3: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
0000:00:04.0: ICS LAN PHY transceiver found at address 1.
0000:00:04.0: Using transceiver found at address 1 as default
eth0: SiS 900 PCI Fast Ethernet at 0x2000, IRQ 11, 00:00:e2:a0:df:8a.
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00012410320ff3da]
Yenta: ISA IRQ mask 0x0000, PCI irq 11
Socket status: 30000006
ACPI: PCI Interrupt 0000:00:09.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:00:09.1 [17c0:3202]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:09.1, mfunc 0x01001022, devctl 0x44
before wait 2
Yenta: ISA IRQ mask 0x0410, PCI irq 11
Socket status: 30000006
before wait 2
before wait 2
before wait 2
AllowedChannel = dea08000
Region:56992
before wait 2
before wait 2
cs: IO port probe 0x3e0-0x4ff: excluding 0x480-0x48f
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x480-0x48f
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xa00-0xaff: clean.
before wait 2
before wait 2
before wait 2
before wait 2
before wait 2
before wait 2
before wait 2
before wait 2
before wait 2
before wait 2
before wait 2
before wait 2
eth0: Media Link Off
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
before wait 2
before wait 2
before wait 2
before wait 2
before wait 2
before wait 2
hub 3-1:1.0: hub_port_status failed (err = -110)
usbcore: registered new driver hiddev
usb 3-1.3: USB disconnect, address 3
zd1211_disconnect
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
usb 4-3: new high speed USB device using ehci_hcd and address 2
hub 4-3:1.0: USB hub found
hub 4-3:1.0: 4 ports detected
usb 3-1: USB disconnect, address 2
usb 2-2: USB disconnect, address 2
usb 2-2: new low speed USB device using ohci_hcd and address 3
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:03.1-2
usb 4-3.3: new high speed USB device using ehci_hcd and address 4
Release Ver = 4721
EEPORM Ver = 4330
PA type: 0
AllowedChannel = 000107ff
Region:48
SSID element: data [8]:
00 06 6d 73 68 6f 6d 65
SupportedRate element: data [6]:
01 04 82 84 8b 96
STA_ASSOCIATED
mac addr = 00:13:49:09:b8:f7
NET: Registered protocol family 10
Disabled Privacy Extensions on device c036b920(lo)
IPv6 over IPv4 tunneling driver
ACPI: AC Adapter [AC] (off-line)
ACPI: Battery Slot [BAT0] (battery absent)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWB]
ACPI: Sleep Button (CM) [SLP2]
ACPI: Lid Switch [LID]
IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
IA-32 Microcode Update Driver v1.14 unregistered
powernow: This module only works with AMD K7 CPUs
subfs 0.9
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
subfs: unsuccessful attempt to mount media (256)
eth0: no IPv6 routers present
wlan0: no IPv6 routers present
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
end_request: I/O error, dev fd0, sector 0
subfs: unsuccessful attempt to mount media (256)
usb 4-3.4: new full speed USB device using ehci_hcd and address 5
ALSA sound/usb/usbaudio.c:2455: found format II with max.bitrate = 640, frame size=1536
usbcore: registered new driver midi
ALSA sound/usb/usbmixer.c:1653: status interrupt: c0 18
ALSA sound/usb/usbmixer.c:1638: memory change in unknown unit 24
[/HTML]

lsusb
Quote:
Bus 004 Device 005: ID 041e:3000 Creative Technology, Ltd
Bus 004 Device 004: ID 0ace:1211 ZyDAS 802.11b/g USB2 WiFi
Bus 004 Device 002: ID 0409:0058 NEC Corp. HighSpeed Hub
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 003: ID 046d:c501 Logitech, Inc. Cordless Mouse Receiver
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000
 
Old 02-05-2006, 02:18 PM   #2
halvy
Member
 
Registered: Aug 2005
Location: Boston Massachussets, USA
Distribution: Anything NOT SystemD (ie. M$) related.
Posts: 900

Rep: Reputation: 41
sometimes the switch for disabling on board stuff is on the mobo.

regardless-- you will NEED a good driver for that usb sound card. hunt for it, the manufacture and maintainers don't always have the best one... individuals do however-- who are working on this hardware.

i will now preach: STAY AWAY FROM ANYTHING USB UNLESS YOU *MUST* HAVE IT!! lol

good luck, lettuce know

Last edited by halvy; 02-05-2006 at 07:06 PM.
 
Old 02-05-2006, 02:26 PM   #3
suhis
Member
 
Registered: Dec 2003
Distribution: Suse 8.2
Posts: 48

Original Poster
Rep: Reputation: 15
ok i forgot to mention.. my pc is fujitsu siemens d8820 and it's laptop ..
and it works in my friends laptop without any problems (it was about 2mins and we got it working and it worked better than in windows ). and i once got it working but i dont know what i did .. it was early in the morning and i decided to test few things .. and it worked .. now it doesn't want to work and im sure it's because of that integrated shit
 
Old 02-05-2006, 07:08 PM   #4
halvy
Member
 
Registered: Aug 2005
Location: Boston Massachussets, USA
Distribution: Anything NOT SystemD (ie. M$) related.
Posts: 900

Rep: Reputation: 41
no, even if you get that intergrated card taken off line, you STILL need a good driver for your usb card!!

you SHOULD be able to put ten (10) soundcards in if you want.. (this is linux, remember

be patient.. we'll figure it out.
 
Old 02-06-2006, 09:45 AM   #5
suhis
Member
 
Registered: Dec 2003
Distribution: Suse 8.2
Posts: 48

Original Poster
Rep: Reputation: 15
but it works very nicely in my friends laptop (suse 10.0 too, plug in, power on, wait a few secs and it works ) and my laptop finds it but cant make sound (i think it's because of that crappy integrated. because i have read that extigy needs to be no. 1 card).. and i have heard from many people that it works without anything special
 
Old 02-06-2006, 03:44 PM   #6
halvy
Member
 
Registered: Aug 2005
Location: Boston Massachussets, USA
Distribution: Anything NOT SystemD (ie. M$) related.
Posts: 900

Rep: Reputation: 41
Quote:
Originally Posted by suhis
but it works very nicely in my friends laptop (suse 10.0 too, plug in, power on, wait a few secs and it works ) and my laptop finds it but cant make sound (i think it's because of that crappy integrated. because i have read that extigy needs to be no. 1 card).. and i have heard from many people that it works without anything special
suite yourself, that is just my opinion of what 'might' help.

that fact that it works on another computer means nothing, except that the card is not broken.

linux comes in a million flavors, so each one is just different enough to be uncompatible with other various software or hardware.

good luck.
 
Old 02-06-2006, 03:58 PM   #7
palceksmuk
LQ Newbie
 
Registered: Dec 2005
Distribution: slackware 10.2
Posts: 26

Rep: Reputation: 15
If kmix works and xmms can't output maybe arts is blocking the soundcard.
If you think the problem is the onboard card you could try disabling the module for the onboard soundcard in modules.conf
 
Old 02-07-2006, 11:02 AM   #8
suhis
Member
 
Registered: Dec 2003
Distribution: Suse 8.2
Posts: 48

Original Poster
Rep: Reputation: 15
and i have also tried those exaudio (extigy oss drivers) drivers and they didn't work either.

what is arts and how i make it not to block my sound
 
Old 02-07-2006, 03:44 PM   #9
halvy
Member
 
Registered: Aug 2005
Location: Boston Massachussets, USA
Distribution: Anything NOT SystemD (ie. M$) related.
Posts: 900

Rep: Reputation: 41
Quote:
Originally Posted by suhis
and i have also tried those exaudio (extigy oss drivers) drivers and they didn't work either.

what is arts and how i make it not to block my sound
it should NOT be necessary to take arts completely 'out'.

if you do you will loose some of your sound abilities.

i doubt taking arts out will fix your problem because your card is NOT being recognized yet.

Last edited by halvy; 02-07-2006 at 03:47 PM.
 
Old 02-07-2006, 04:41 PM   #10
palceksmuk
LQ Newbie
 
Registered: Dec 2005
Distribution: slackware 10.2
Posts: 26

Rep: Reputation: 15
Arts is the kde sound server. When two programs want to use your sound card at the same time one of them can't do it, thats when arts act as something between the programs and the soundcard and mix the music from both programs and pass it to the soudcard. So if xmms would be set to use arts as an output there shouldn't be two programs trying to access the soundcard at the same time.
I would try killing arts just to see if arts is causing problems. Try typing killall artsd in a terminal.
You can also try to go to the kde control center and in the sound section there is the sound system (arts). There you can set the autosuspend time to something small for example 10 seconds so when nobody uses arts xmms and other programs that don't use arts can access the soundcard.
 
Old 02-08-2006, 07:53 AM   #11
suhis
Member
 
Registered: Dec 2003
Distribution: Suse 8.2
Posts: 48

Original Poster
Rep: Reputation: 15
... now i got it working ... yesterday that xxms error message disappeared (i didn't do anything ) and then it starts to play those music files... without sound .. today i loaded uhci-hcd (modprobe -v uhci-hcd) and it works almost perfectly
 
Old 02-08-2006, 02:04 PM   #12
halvy
Member
 
Registered: Aug 2005
Location: Boston Massachussets, USA
Distribution: Anything NOT SystemD (ie. M$) related.
Posts: 900

Rep: Reputation: 41
qool beans
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
sound in debian sarge (intel i810 integrated) not working with alsa sea turtle Linux - Hardware 4 10-19-2006 11:13 PM
Integrated Sound Card not working drethenerd Linux - Hardware 5 06-10-2005 03:10 PM
Sound Blaster Extigy USB Card Creeps Linux - Hardware 1 10-06-2004 02:04 PM
new to linux, trying to get my USB Extigy sound card to work dcguy918 Linux - Hardware 4 03-13-2004 03:39 PM
cdda and external (usb port) extigy sound card pdudzik Linux - General 0 11-19-2003 11:09 AM


All times are GMT -5. The time now is 03:27 PM.

Main Menu
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
identi.ca: @linuxquestions
Facebook: linuxquestions Google+: linuxquestions
Open Source Consulting | Domain Registration