san disk not being presented correctly to ql2340L card
output from tail of dmesg command :
QLogic Fibre Channel HBA Driver ACPI: PCI Interrupt 0000:02:05.0[A] -> GSI 24 (level, low) -> IRQ 193 qla2300 0000:02:05.0: Found an ISP2312, irq 193, iobase 0xffffc2000001c000 qla2300 0000:02:05.0: Configuring PCI space... qla2300 0000:02:05.0: Configure NVRAM parameters... qla2300 0000:02:05.0: Verifying loaded RISC code... qla2300 0000:02:05.0: Waiting for LIP to complete... qla2300 0000:02:05.0: LIP reset occured (f7f7). qla2300 0000:02:05.0: LOOP UP detected (2 Gbps). qla2300 0000:02:05.0: Topology - (F_Port), Host Loop address 0xffff scsi5 : qla2xxx qla2300 0000:02:05.0: QLogic Fibre Channel HBA Driver: 8.01.03-k QLogic QLA2340 - ISP2312: PCI-X (66 MHz) @ 0000:02:05.0 hdma-, host#=5, fw=3.03.18 IPX ACPI: PCI Interrupt 0000:03:01.0[A] -> GSI 28 (level, low) -> IRQ 201 qla2300 0000:03:01.0: Found an ISP2312, irq 201, iobase 0xffffc2000001e000 qla2300 0000:03:01.0: Configuring PCI space... qla2300 0000:03:01.0: Configure NVRAM parameters... scsi: unknown device type 12 Vendor: COMPAQ Model: HSV110 (C)COMPAQ Rev: 3025 Type: RAID ANSI SCSI revision: 02 5:0:0:0: Attached scsi generic sg1 type 12 Vendor: COMPAQ Model: HSV110 (C)COMPAQ Rev: 3025 Type: Direct-Access ANSI SCSI revision: 02 SCSI device sdb: 104857600 512-byte hdwr sectors (53687 MB) SCSI device sdb: drive cache: write through SCSI device sdb: 104857600 512-byte hdwr sectors (53687 MB) SCSI device sdb: drive cache: write through sdb: unknown partition table sd 5:0:0:1: Attached scsi disk sdb sd 5:0:0:1: Attached scsi generic sg2 type 0 scsi: unknown device type 12 Vendor: COMPAQ Model: HSV110 (C)COMPAQ Rev: 3025 Type: RAID ANSI SCSI revision: 02 5:0:1:0: Attached scsi generic sg3 type 12 Vendor: COMPAQ Model: HSV110 (C)COMPAQ Rev: 3025 Type: Direct-Access ANSI SCSI revision: 02 SCSI device sdc: 104857600 512-byte hdwr sectors (53687 MB) sdc: asking for cache data failed sdc: assuming drive cache: write through SCSI device sdc: 104857600 512-byte hdwr sectors (53687 MB) sdc: asking for cache data failed sdc: assuming drive cache: write through sdc:<6>sd 5:0:1:1: Device not ready. end_request: I/O error, dev sdc, sector 0 Buffer I/O error on device sdc, logical block 0 sd 5:0:1:1: Device not ready. end_request: I/O error, dev sdc, sector 0 Buffer I/O error on device sdc, logical block 0 unable to read partition table sd 5:0:1:1: Attached scsi disk sdc sd 5:0:1:1: Attached scsi generic sg4 type 0 scsi: unknown device type 12 Vendor: COMPAQ Model: HSV110 (C)COMPAQ Rev: 3025 Type: RAID ANSI SCSI revision: 02 5:0:2:0: Attached scsi generic sg5 type 12 scsi: unknown device type 12 Vendor: COMPAQ Model: HSV110 (C)COMPAQ Rev: 3025 Type: RAID ANSI SCSI revision: 02 5:0:3:0: Attached scsi generic sg6 type 12 qla2300 0000:03:01.0: Verifying loaded RISC code... qla2300 0000:03:01.0: Waiting for LIP to complete... qla2300 0000:03:01.0: Cable is unplugged... scsi6 : qla2xxx qla2300 0000:03:01.0: QLogic Fibre Channel HBA Driver: 8.01.03-k QLogic QLA2340 - ISP2312: PCI-X (133 MHz) @ 0000:03:01.0 hdma-, host#=6, fw=3.03.18 IPX there is only one 50Gig disk presented to my machine. There is only one path from the fc card to the SAN. what is the error regarding the disk? has anyone seen this or dealt with this before? Im getting a bit frustrated now as i cant seem to progress anyfurther. i have installed lsscsi and systool from source and the output from both follow lsscsi [0:0:0:0] disk LSILOGIC 1030 IM IM 1000 /dev/sda [5:0:0:0] storage COMPAQ HSV110 (C)COMPAQ 3025 - [5:0:0:1] disk COMPAQ HSV110 (C)COMPAQ 3025 - [5:0:1:0] storage COMPAQ HSV110 (C)COMPAQ 3025 - [5:0:1:1] disk COMPAQ HSV110 (C)COMPAQ 3025 - [5:0:2:0] storage COMPAQ HSV110 (C)COMPAQ 3025 - [5:0:3:0] storage COMPAQ HSV110 (C)COMPAQ 3025 - systool -v -b scsi 5:0:0:1 Bus = "scsi" Device = "5:0:0:1" Device path = "/sys/devices/pci0000:00/0000:00:0a.0/0000:02:05.0/host5/rport-5:0-0/target5:0:0/5:0:0:1" delete = <store method only> device_blocked = "0" iocounterbits = "32" iodone_cnt = "0xc" ioerr_cnt = "0x1" iorequest_cnt = "0xc" model = "HSV110 (C)COMPAQ" queue_depth = "32" queue_type = "none" rescan = <store method only> rev = "3025" scsi_level = "3" state = "running" timeout = "30" type = "0" uevent = <store method only> vendor = "COMPAQ " dont know how to prceed... does anyone else? Ronan SlamD (64BitSlackware) 10.1 kernel 2.6.15.1 |
could a moderator please move this post to enterprise linux category please!? I dont want to double post, but I feel it would be better for this post to reside there.
Ronan PS - anyone have any ideas as to how i can proceed with the above problem.. :) |
All times are GMT -5. The time now is 08:22 AM. |