Hi,
This is my first linux post and a complete noob, just installed fedora core 5, everythings working fine, i also updated the pccardutils

When i insert my ZTE MC 315 pcmcia card and do a dmesg it shows :

pccard: PCMCIA card inserted into slot 0
pcmcia: registering new device pcmcia0.0
ttyS3: detected caps 00000700 should be 00000100
0.0: ttyS3 at I/O 0x2e8 (irq = 3) is a 16C950/954

it is bound to serial_cs
and when i do a pccardctl info it shows:

PRODID_1="CDMA1X"
PRODID_2="CARD"
PRODID_3=""
PRODID_4=""
MANFID=0279,950b
FUNCID=2
PRODID_1=""
PRODID_2=""
PRODID_3=""
PRODID_4=""
MANFID=0000,0000
FUNCID=255

I also created a wvdial.conf entry as following:

[Dialer Defaults]
Modem = /dev/ttyS3
Init1 = ATZ
ISDN = 0
Carrier Check = no
Stupid Mode = yes
Modem Type = Analog Modem
Phone = #777
Username = [myphonenumber]
Password = [myphonenumber]

and when i do wvdial:
--> WvDial: Internet dialer version 1.54.0
--> Initializing modem.
--> Sending: ATZ
--> Sending: ATQ0
--> Re-Sending: ATZ
--> Modem not responding.


I understand that ZTE card config information is not there , i couldnt find it on thier website too

Can somebody please guide me, im kinda frustrated with my first linux experiance, but im adament in using it rather than windows

Thanx N Regards
Mat

take out the card

then run this command

#tail -f /var/log/messages

reinsert the card and post the output of the changes!!!!

secondly aslo check that the socket tty3 exists in dev directory or not

check the permissions make sure it is executable

[QUOTE=simplenoob]Hi,
This is my first linux post and a complete noob, just installed fedora core 5, everythings working fine, i also updated the pccardutils

When i insert my ZTE MC 315 pcmcia card and do a dmesg it shows :

pccard: PCMCIA card inserted into slot 0
pcmcia: registering new device pcmcia0.0
ttyS3: detected caps 00000700 should be 00000100
0.0: ttyS3 at I/O 0x2e8 (irq = 3) is a 16C950/954

it is bound to serial_cs
and when i do a pccardctl info it shows:

PRODID_1="CDMA1X"
PRODID_2="CARD"
PRODID_3=""
PRODID_4=""
MANFID=0279,950b
FUNCID=2
PRODID_1=""
PRODID_2=""
PRODID_3=""
PRODID_4=""
MANFID=0000,0000
FUNCID=255

I also created a wvdial.conf entry as following:

[Dialer Defaults]
Modem = /dev/ttyS3
Init1 = ATZ
ISDN = 0
Carrier Check = no
Stupid Mode = yes
Modem Type = Analog Modem
Phone = #777
Username = [myphonenumber]
Password = [myphonenumber]

and when i do wvdial:
--> WvDial: Internet dialer version 1.54.0
--> Initializing modem.
--> Sending: ATZ
--> Sending: ATQ0
--> Re-Sending: ATZ
--> Modem not responding.


I understand that ZTE card config information is not there , i couldnt find it on thier website too

Can somebody please guide me, to solve the problem.

with regards
N.Sampath