LinuxQuestions.org
View the Most Wanted LQ Wiki articles.
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Hardware
User Name
Password
Linux - Hardware This forum is for Hardware issues.
Having trouble installing a piece of hardware? Want to know if that peripheral is compatible with Linux?

Notices



Reply
 
Search this Thread
Old 07-22-2004, 05:43 AM   #1
zby
LQ Newbie
 
Registered: Jun 2004
Distribution: Debian
Posts: 8

Rep: Reputation: 0
Plugging devices on USB does not give any effect (kernel 2.6.6)


I have compiled a 2.6.6 kernel with all USB support in the kernel (not as modules).
When I plug in a flash card I get nothing in /var/log/messages and it is not listed by lsusb.

Here is some additional data:

=============================

# ls /proc/bus/usb/
001 devices

I have 4 USB sockets on my Epox motherboard.

==============================

# lsusb
Bus 001 Device 001: ID 0000:0000

This does not change when I plug in the flash memory. The led on the flash stick turns on for a short time then shitches off.

==============================

# cat /proc/bus/usb/devices

T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 6
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.6 ehci_hcd
S: Product=nVidia Corporation nForce2 USB Controller
S: SerialNumber=0000:00:02.2
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms

==============================

And boot messages:

ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
ehci_hcd 0000:00:02.2: nVidia Corporation nForce2 USB Controller
ehci_hcd 0000:00:02.2: reset hcs_params 0x102486 dbg=1 cc=2 pcc=4 !ppc ports=6
ehci_hcd 0000:00:02.2: reset portroute 0 0 1 1 1 0
ehci_hcd 0000:00:02.2: reset hcc_params a086 caching frame 256/512/1024 park
ehci_hcd 0000:00:02.2: capability 0001 at a0
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: irq 20, pci mem e080a000
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.2: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: init command 010b09 park=3 ithresh=1 period=256 RUN
ehci_hcd 0000:00:02.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29
ehci_hcd 0000:00:02.2: root hub device address 1
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: default language 0x0409
usb usb1: Product: nVidia Corporation nForce2 USB Controller
usb usb1: Manufacturer: Linux 2.6.6 ehci_hcd
usb usb1: SerialNumber: 0000:00:02.2
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: ganged power switching
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: hub controller current requirement: 0mA
hub 1-0:1.0: local power source is good
hub 1-0:1.0: enabling power on all ports
USB Universal Host Controller Interface driver v2.2
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
ehci_hcd 0000:00:02.2: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 2, status 501, change 1, 480 Mb/s
input: AT Translated Set 2 keyboard on isa0060/serio0
Advanced Linux Sound Architecture Driver Version 1.0.4rc2 (Tue Mar 30 08:19:30 2004 UTC).
PCI: Setting latency timer of device 0000:00:06.0 to 64
hub 1-0:1.0: debounce: port 2: delay 100ms stable 4 status 0x501
ehci_hcd 0000:00:02.2: port 2 full speed --> companion
ehci_hcd 0000:00:02.2: GetStatus port 2 status 003001 POWER OWNER sig=se0 CONNECT
 
Old 07-22-2004, 10:27 AM   #2
zby
LQ Newbie
 
Registered: Jun 2004
Distribution: Debian
Posts: 8

Original Poster
Rep: Reputation: 0
I've solved that. I did not compile in OHCI driver. It seems that this one works.
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
USB devices on Slackware, kernel 2.6.12.5 jaakkop Linux - Hardware 8 10-09-2005 12:28 AM
SuSE 9.1 freezes when plugging in USB devices lorenzo123 Linux - Hardware 1 05-27-2004 09:24 AM
Pb with kernel 2.6.4 to give users' right to /proc/bus/usb on a Slackware 9.1 myxmyx Linux - Software 0 04-29-2004 02:39 AM
Kernel 2.4.23 won't boot after plugging in usb mouse mi6 Slackware 5 12-13-2003 06:34 AM
Plugging in USB devices freezes RH 7.3 jrapczak Linux - Hardware 1 10-28-2003 05:25 PM


All times are GMT -5. The time now is 08:12 PM.

Main Menu
Advertisement
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
identi.ca: @linuxquestions
Facebook: linuxquestions Google+: linuxquestions
Open Source Consulting | Domain Registration