LinuxQuestions.org
View the Most Wanted LQ Wiki articles.
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Hardware
User Name
Password
Linux - Hardware This forum is for Hardware issues.
Having trouble installing a piece of hardware? Want to know if that peripheral is compatible with Linux?

Notices

Reply
 
Search this Thread
Old 09-14-2005, 05:01 PM   #1
nescio05
LQ Newbie
 
Registered: Sep 2005
Posts: 1

Rep: Reputation: 0
keyboard lag when ifdown eth0 (natsemi) with kernel 2.4.31


Hi,

I have an HP Omnibook XE4500 with a SuSE 8.0 distro.
Recently I changed from the original 2.4.18-SuSE kernel to
2.4.31 from kernel.org in order to get my wireless card working (madwifi driver,
it works now).

However, now I found that the keyboard lags (about 0.5s lag)
after turning down my ethernet card (DP83815) (my eth0 is configured as dhcp,
start mode manual in ifcfg-eth0):

ifup eth0 -> everything as usual
ifdown eth0 -> keyboard lags, top looks as usual, i.e. 100% idle
ifup eth0 again -> keyboard is ok again.

With the old 2.4.18 kernel everything is fine.

When using another ifcfg with a static address the keyboard does not lag
after turning the interface down again.
So I first suspected dhcpcd, but I also see the effect on the console
after booting (no X) :

ip link set eth0 up -> ok
ip link set eth0 down -> keyboard lags
ip link set eth0 up -> ok again

Does anybody know what exactly could be wrong, i.e. where to search
for the error (iproute2, kernel, natsemi driver)?
Could it be connected to the message "remaining active for wake-on-lan" (see below),
which I think was not there with 2.4.18 ?


Boot messages:
------------------

Inspecting /boot/System.map-2.4.31
Loaded 18129 symbols from /boot/System.map-2.4.31.
Symbols match kernel version 2.4.31.
No module symbols loaded.
klogd 1.4.1, log source = ksyslog started.
<4>Linux version 2.4.31 (root@linux) (gcc version 2.95.3 20010315 (SuSE)) #7 Tue Sep 13 16:46:56 CEST 2005
<6>BIOS-provided physical RAM map:
<4> BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
<4> BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
<4> BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
<4> BIOS-e820: 0000000000100000 - 000000000fef0000 (usable)
<4> BIOS-e820: 000000000fef0000 - 000000000feff000 (ACPI data)
<4> BIOS-e820: 000000000feff000 - 000000000ff00000 (ACPI NVS)
<4> BIOS-e820: 000000000ff00000 - 0000000010000000 (reserved)
<4> BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
<5>254MB LOWMEM available.
<4>On node 0 totalpages: 65264
<4>zone(0): 4096 pages.
<4>zone(1): 61168 pages.
<4>zone(2): 0 pages.
<6>ACPI: RSDP (v000 PTLTD ) @ 0x000f6c90
<6>ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x0fef89fa
<6>ACPI: FADT (v001 ALI M1533 0x06040000 PTL 0x000f4240) @ 0x0fefef64
<6>ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x0fefefd8
<6>ACPI: DSDT (v001 ALI M1533 0x06040000 MSFT 0x0100000d) @ 0x00000000
<4>Kernel command line: auto BOOT_IMAGE=linux-2.4.31 ro root=307 lba32 idebus=66 acpismp=force hdc=ide-scsi pci=biosirq
<6>ide_setup: idebus=66
<6>ide_setup: hdc=ide-scsi
<6>Initializing CPU#0
<4>Detected 1600.055 MHz processor.
<4>Console: colour VGA+ 80x50
<4>Calibrating delay loop... 3191.60 BogoMIPS
<6>Memory: 255752k/261056k available (1294k kernel code, 4916k reserved, 500k data, 72k init, 0k highmem)
<6>Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
<6>Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
<6>Mount cache hash table entries: 512 (order: 0, 4096 bytes)
<6>Buffer cache hash table entries: 16384 (order: 4, 65536 bytes)
<4>Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>CPU: Trace cache: 12K uops, L1 D cache: 8K
<6>CPU: L2 cache: 512K
<7>CPU: After generic, caps: 3febf9ff 00000000 00000000 00000000
<7>CPU: Common caps: 3febf9ff 00000000 00000000 00000000
<4>CPU: Intel(R) Pentium(R) 4 Mobile CPU 1.60GHz stepping 04
<6>Enabling fast FPU save and restore... done.
<6>Enabling unmasked SIMD FPU exception support... done.
<6>Checking 'hlt' instruction... OK.
<4>ACPI: IRQ9 SCI: Level Trigger.
<4>POSIX conformance testing by UNIFIX
<4>mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
<4>mtrr: detected mtrr type: Intel
<6>ACPI: Subsystem revision 20040326
<6>PCI: PCI BIOS revision 2.10 entry at 0xfd89b, last bus=3
<6>PCI: Using configuration type 1
<6>ACPI: Interpreter enabled
<6>ACPI: Using PIC for interrupt routing
<6>ACPI: System [ACPI] (supports S0 S3 S4 S5)
<6>ACPI: PCI Root Bridge [PCI0] (00:00)
<4>PCI: Probing PCI hardware (bus 00)
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
<4>ACPI: PCI Interrupt Link [LNKA] (IRQs 10) *9
<4>ACPI: PCI Interrupt Link [LNKB] (IRQs 7 *11)
<4>ACPI: PCI Interrupt Link [LNKC] (IRQs 10) *0, disabled.
<4>ACPI: PCI Interrupt Link [LNKD] (IRQs 10) *0, disabled.
<4>ACPI: PCI Interrupt Link [LNKE] (IRQs 10) *0, disabled.
<4>ACPI: PCI Interrupt Link [LNKF] (IRQs 5 7) *0, disabled.
<4>ACPI: PCI Interrupt Link [LNKG] (IRQs 10) *0, disabled.
<4>ACPI: PCI Interrupt Link [LNKH] (IRQs *5 7)
<4>ACPI: PCI Interrupt Link [LNKU] (IRQs *10)
<6>ACPI: Embedded Controller [EC0] (gpe 24)
<3>schedule_task(): keventd has not started
<6>PCI: Probing PCI hardware
<4>ACPI: PCI Interrupt Link [LNKU] enabled at IRQ 10
<4>ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 5
<4>ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 10
<4>ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 7
<4>ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
<4>PCI: No IRQ known for interrupt pin A of device 00:10.0
<4>ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
<4>ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
<6>PCI: Using ACPI for IRQ routing
<6>Linux NET4.0 for Linux 2.4
<6>Based upon Swansea University Computer Society NET3.039
<4>Initializing RT netlink socket
<4>Starting kswapd
<6>ACPI: AC Adapter [ACAD] (on-line)
<6>ACPI: Battery Slot [BAT1] (battery present)
<6>ACPI: Power Button (FF) [PWRF]
<6>ACPI: Lid Switch [LID]
<6>ACPI: Processor [CPU0] (supports C1 C2 C3, 2 performance states)
<6>ACPI: Thermal Zone [THRM] (51 C)
<4>pty: 256 Unix98 ptys configured
<6>Real Time Clock Driver v1.10f
<6>Floppy drive(s): fd0 is 1.44M
<6>FDC 0 is a post-1991 82077
<6>Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
<6>ide: Assuming 66MHz system bus speed for PIO modes
<6>ALI15X3: IDE controller at PCI slot 00:10.0
<4>PCI: No IRQ known for interrupt pin A of device 00:10.0
<6>ALI15X3: chipset revision 196
<6>ALI15X3: not 100%% native mode: will probe irqs later
<6> ide0: BM-DMA at 0x1800-0x1807, BIOS settings: hda:DMA, hdb:pio
<6> ide1: BM-DMA at 0x1808-0x180f, BIOS settings: hdc:pio, hdd:pio
<4>hda: IC25N030ATCS04-0, ATA DISK drive
<4>blk: queue c02fe720, I/O limit 4095Mb (mask 0xffffffff)
<4>hdc: TOSHIBA DVD-ROM SD-R2212, ATAPI CD/DVD-ROM drive
<4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
<4>ide1 at 0x170-0x177,0x376 on irq 15
<4>hda: attached ide-disk driver.
<4>hda: host protected area => 1
<6>hda: 58605120 sectors (30006 MB) w/1768KiB Cache, CHS=3648/255/63, UDMA(100)
<4>hdc: attached ide-scsi driver.
<6>Partition check:
<6> hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 >
<6>SCSI subsystem driver Revision: 1.00
<6>scsi0 : SCSI host adapter emulation for IDE ATAPI devices
<4> Vendor: TOSHIBA Model: DVD-ROM SD-R2212 Rev: 1913
<4> Type: CD-ROM ANSI SCSI revision: 02
<4>Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
<4>sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
<6>Uniform CD-ROM driver Revision: 3.12
<6>Linux Kernel Card Services 3.1.22
<6> options: [pci] [cardbus] [pm]
<4>PCI: Enabling device 00:0a.0 (0000 -> 0002)
<4>PCI: Enabling device 00:0a.1 (0000 -> 0002)
<6>Initializing Cryptographic API
<6>NET4: Linux TCP/IP 1.0 for NET4.0
<6>IP Protocols: ICMP, UDP, TCP
<6>IP: routing cache hash table of 2048 buckets, 16Kbytes
<6>TCP: Hash tables configured (established 16384 bind 16384)
<6>NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
<6>Yenta ISA IRQ mask 0x0c38, PCI irq 7
<6>Socket status: 30000006
<6>Yenta ISA IRQ mask 0x0c38, PCI irq 7
<6>Socket status: 30000006
<4>reiserfs: found format "3.6" with standard journal
<4>reiserfs: checking transaction log (device ide0(3,7)) ...
<4>for (ide0(3,7))
<4>ide0(3,7):Using r5 hash to sort names
<4>VFS: Mounted root (reiserfs filesystem) readonly.
<6>Freeing unused kernel memory: 72k freed
<6>Adding Swap: 377488k swap-space (priority 42)
Kernel logging (ksyslog) stopped.
Kernel log daemon terminating.


Message from natsemi module:
-----------------------------------

Sep 14 14:59:23 linux kernel: natsemi dp8381x driver, version 1.07+LK1.0.17, Sep 27, 2002
Sep 14 14:59:23 linux kernel: originally by Donald Becker <becker@scyld.com>
Sep 14 14:59:23 linux kernel: 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
Sep 14 14:59:23 linux kernel: eth0: NatSemi DP8381[56] at 0xd08f9000, <MAC>, IRQ 11.


When turning up & down interface:
----------------------------------------

Sep 14 15:00:04 linux kernel: eth0: link up.
Sep 14 15:00:04 linux kernel: eth0: Setting full-duplex based on negotiated link capability.
Sep 14 15:00:17 linux kernel: eth0: remaining active for wake-on-lan


lspci -vv: (using 2.4.18 kernel)
-----------

00:00.0 Host bridge: Acer Laboratories Inc. [ALi]: Unknown device 1671 (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 0
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [b0] AGP version 2.0
Status: RQ=27 SBA+ 64bit- FW+ Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [a4] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:01.0 PCI bridge: Acer Laboratories Inc. [ALi] M5247 (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: e0100000-e01fffff
Prefetchable memory behind bridge: e8000000-efffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-

00:02.0 USB Controller: Acer Laboratories Inc. [ALi] M5237 USB (rev 03) (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company: Unknown device 0025
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at e0000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:06.0 Multimedia audio controller: Acer Laboratories Inc. [ALi] M5451 PCI South Bridge Audio (rev 02)
Subsystem: Hewlett-Packard Company: Unknown device 0025
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR+ <PERR+
Latency: 64 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at 1000 [size=256]
Region 1: Memory at e0001000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.0 ISA bridge: Acer Laboratories Inc. [ALi] M1533 PCI to ISA Bridge [Aladdin IV]
Subsystem: Acer Laboratories Inc. [ALi] ALI M1533 Aladdin IV ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [a0] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:08.0 Modem: Acer Laboratories Inc. [ALi]: Unknown device 5457 (prog-if 00 [Generic])
Subsystem: Hewlett-Packard Company: Unknown device 0025
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 9
Region 0: Memory at e0002000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 1400 [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0a.0 CardBus bridge: Texas Instruments: Unknown device ac55 (rev 01)
Subsystem: Hewlett-Packard Company: Unknown device 0025
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 5
Region 0: Memory at 10000000 (32-bit, non-prefetchable) [disabled] [size=4K]
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Memory window 0: 00000000-0000f000 [disabled] (prefetchable)
I/O window 0: 00000000-00000003 [disabled]
I/O window 1: 00000000-00000003 [disabled]
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- PostWrite-
16-bit legacy interface ports at 0001

00:0a.1 CardBus bridge: Texas Instruments: Unknown device ac55 (rev 01)
Subsystem: Hewlett-Packard Company: Unknown device 0025
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 5
Region 0: Memory at 10001000 (32-bit, non-prefetchable) [disabled] [size=4K]
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Memory window 0: 00000000-0000f000 [disabled] (prefetchable)
I/O window 0: 00000000-00000003 [disabled]
I/O window 1: 00000000-00000003 [disabled]
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- PostWrite-
16-bit legacy interface ports at 0001

00:0c.0 FireWire (IEEE 1394): Texas Instruments: Unknown device 8026 (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company: Unknown device 0025
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 9
Region 0: Memory at e0003000 (32-bit, non-prefetchable) [disabled] [size=2K]
Region 1: Memory at e0004000 (32-bit, non-prefetchable) [disabled] [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:10.0 IDE interface: Acer Laboratories Inc. [ALi] M5229 IDE (rev c4) (prog-if b0)
Subsystem: Hewlett-Packard Company: Unknown device 0025
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 0
Region 4: I/O ports at 1800 [size=16]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.0 Bridge: Acer Laboratories Inc. [ALi] M7101 PMU
Subsystem: Hewlett-Packard Company: Unknown device 0025
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:12.0 Ethernet controller: National Semiconductor Corporation DP83815 (MacPhyter) Ethernet Controller
Subsystem: Unknown device 3c08:a400
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 90 (2750ns min, 13000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 1c00 [size=256]
Region 1: Memory at e0008000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=320mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+

01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M6 LY (prog-if 00 [VGA])
Subsystem: Hewlett-Packard Company: Unknown device 0025
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B+
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 9
Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 9000 [size=256]
Region 2: Memory at e0100000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=47 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA+ AGP- 64bit- FW- Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
ifdown eth0 works but doesn't work? vdemuth Linux - Networking 7 12-03-2010 10:37 AM
no eth0 with natsemi linuxhippy Slackware 1 08-31-2005 10:37 AM
ifdown eth0 slows the typing down (???) fcarli Linux - General 1 11-07-2003 10:45 AM
needs to ifdown eth0 before using internet jay820 Linux - Networking 14 07-20-2003 08:11 AM
natsemi.c / Scyld / Kernel 2.4.5 newb Linux - Networking 3 07-04-2001 06:21 AM


All times are GMT -5. The time now is 07:57 PM.

Main Menu
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
identi.ca: @linuxquestions
Facebook: linuxquestions Google+: linuxquestions
Open Source Consulting | Domain Registration