Installing USB hard drive
I'm having trouble installing my new Western Digital 120gb USB hard drive. It seems to be recognized, but the device doesn't appear anywhere.
Here's the pertinent bits of my dmesg: hub.c: USB hub found hub.c: 2 ports detected hub.c: new USB device 02:0e.0-1, assigned address 2 usb-storage: act_altsettting is 0 usb-storage: id_index calculated to be: 89 usb-storage: Array length appears to be: 91 usb-storage: USB Mass Storage device detected usb-storage: Endpoints: In: 0xc1a91ca0 Out: 0xc1a91cb4 Int: 0x00000000 (Period 0) usb-storage: New GUID 1058030000ac030624020021 usb-storage: GetMaxLUN command result is -32, data is 128 usb-storage: clearing endpoint halt for pipe 0x80000280 usb-storage: Transport: Bulk usb-storage: Protocol: Transparent SCSI usb-storage: *** thread sleeping. scsi0 : SCSI emulation for USB Mass Storage devices usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Command INQUIRY (6 bytes) usb-storage: 12 00 00 00 ff 00 c0 cf 93 65 26 c0 usb-storage: Bulk command S 0x43425355 T 0x1 Trg 0 LUN 0 L 255 F 128 CL 6 usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_transfer_partial(): xfer 255 bytes usb.c: registered new driver usb_mouse usb-storage: usb_stor_bulk_msg() returned 0 xferred 36/255 usb-storage: Bulk data transfer result 0x1 usb-storage: Attempting to get CSW... usb-storage: clearing endpoint halt for pipe 0xc0008280 usb-storage: usb_stor_clear_halt: result=0 usb-storage: Attempting to get CSW (2nd try)... usb-storage: Bulk status result = 0 usb-storage: Bulk status Sig 0x53425355 T 0x1 R 219 Stat 0x0 usb-storage: Fixing INQUIRY data to show SCSI rev 2 usb-storage: scsi cmd done, result=0x0 usb-storage: *** thread sleeping. Vendor: WDC Model: WD1200BB-00DAA3 Rev: 75.1 Type: Direct-Access ANSI SCSI revision: 02 usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Bad LUN (0/1) usb-storage: *** thread sleeping. usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Bad target number (1/0) usb-storage: *** thread sleeping. usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Bad target number (2/0) usb-storage: *** thread sleeping. usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Bad target number (3/0) usb-storage: *** thread sleeping. usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Bad target number (4/0) usb-storage: *** thread sleeping. usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Bad target number (5/0) usb-storage: *** thread sleeping. usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Bad target number (6/0) usb-storage: *** thread sleeping. usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Bad target number (7/0) usb-storage: *** thread sleeping. WARNING: USB Mass Storage data integrity not assured USB Mass Storage device found at 2 usbmouse.c: v1.6:USB HID Boot Protocol mouse driver usb.c: registered new driver hid Can anyone tell me what might be wrong? Edit: I'm using the most recent version of Gentoo |
All times are GMT -5. The time now is 02:53 AM. |