On a Gentoo/AMD64 box running 2.6.17-gentoo-r8 I cannot get my WinTV USB2 card to swap from S-Video input. Is there some magic option I need to pass to the driver? When I tell xawtv to tune to different cable channels all I get is S-Video. However on a Fedora Core 6 box, the card would only use the TV-Tuner... I don't get it.

lsusb:
Bus 001 Device 005: ID 2040:4200 Hauppauge
Bus 001 Device 001: ID 0000:0000
Bus 002 Device 002: ID 046d:c517 Logitech, Inc.
Bus 002 Device 001: ID 0000:0000

lsmod (I cut out the bits I knew weren't applicable to reduce length)
Module Size Used by
--culled--
tda9887 16592 0
tuner 53292 0
tvp5150 17808 0
em28xx 47472 0
compat_ioctl32 8000 1 em28xx
v4l1_compat 11204 1 em28xx
v4l2_common 15872 3 tuner,em28xx,compat_ioctl32
ir_common 25476 1 em28xx
videodev 9600 1 em28xx
tveeprom 15760 1 em28xx
fglrx 622136 116
--culled--
it87 23460 0
hwmon_vid 2688 1 it87
eeprom 6736 0
ds1621 8592 0
i2c_isa 4864 1 it87
--culled--
i2c_nforce2 7168 0
i2c_core 19776 10 tda9887,tuner,tvp5150,em28xx,tveeprom,it87,eeprom,ds1621,i2c_isa,i2c_nforce2
evdev 9664 4

dmesg | grep em28xx:em28xx new video device (2040:4200): interface 0, class 255
em28xx #0: Alternate settings: 8
em28xx #0: Alternate setting 0, max size= 0
em28xx #0: Alternate setting 1, max size= 1024
em28xx #0: Alternate setting 2, max size= 1448
em28xx #0: Alternate setting 3, max size= 2048
em28xx #0: Alternate setting 4, max size= 2304
em28xx #0: Alternate setting 5, max size= 2580
em28xx #0: Alternate setting 6, max size= 2892
em28xx #0: Alternate setting 7, max size= 3072
em28xx #0: AC97 command still being executed: not handled properly!
tuner 2-0063: chip found @ 0xc6 (em28xx #0)
em28xx #0: i2c eeprom 00: 1a eb 67 95 40 20 00 42 20 00 44 03 82 18 6a 18
em28xx #0: i2c eeprom 10: 00 00 24 57 6e 02 00 00 60 00 00 00 02 00 00 00
em28xx #0: i2c eeprom 20: 1e 00 10 10 00 00 00 88 b8 00 00 00 00 00 00 00
em28xx #0: i2c eeprom 30: 00 00 20 40 20 80 02 20 01 01 01 01 00 00 00 00
em28xx #0: i2c eeprom 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 18 03 30 00 30 00
em28xx #0: i2c eeprom 70: 30 00 38 00 37 00 31 00 33 00 38 00 33 00 32 00
em28xx #0: i2c eeprom 80: 00 00 18 03 57 00 69 00 6e 00 54 00 56 00 20 00
em28xx #0: i2c eeprom 90: 55 00 53 00 42 00 32 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom a0: 84 12 00 00 05 50 1a 7f 08 63 23 1c a4 59 16 91
em28xx #0: i2c eeprom b0: ff 00 00 00 04 84 0a 00 01 01 20 77 00 40 68 f6
em28xx #0: i2c eeprom c0: 84 00 74 02 01 0c 03 79 e3 00 00 00 00 00 00 00
em28xx #0: i2c eeprom d0: 84 12 00 00 05 50 1a 7f 08 63 23 1c a4 59 16 91
em28xx #0: i2c eeprom e0: ff 00 00 00 04 84 0a 00 01 01 20 77 00 40 68 f6
em28xx #0: i2c eeprom f0: 84 00 74 02 01 0c 03 79 e3 00 00 00 00 00 00 00
em28xx #0: AC97 command still being executed: not handled properly!
em28xx #0: V4L2 device registered as /dev/video0 and /dev/vbi0
em28xx #0: Found Hauppauge WinTV USB 2
em28xx audio device (2040:4200): interface 1, class 1
em28xx audio device (2040:4200): interface 2, class 1

Thank you in advance!

Is this a WinTV PVR USB2??