Fedora 16 on a Proliant DL380 G4

bradycl_84043 · 11-10-2011, 02:47 PM

I've been fighting with what I assume is a kernel 3 (or rather 3.1)issue since last night but I can't find anyone else reporting the same problem. If anyone can confirm or even justify what I am experiencing, and perhaps help me either find a workaround or file a bug, I would greatly appreciate it.

I have a Proliant DL380 G4 that has run Fedora 12-15 with no issues whatsoever.

Tuesday night, I attempted an upgrade to Fedora 16, of which the first part completed beautifully. However, once it rebooted into the upgrade environment, it complains that it can't find it's kickstart file.

Come to find out, the reason it cannot find the kickstart file is that it is not loading the Smart Array P6i. When the kernel loads the cciss driver it complains that it cannot get IRQ 19, which is taken by one of the USB controllers.

I get the same complaint when trying to install from the F16 DVD. It makes it into anaconda just fine but then complains that it cannot find any drives to install onto.

Throughout this, it continues to happily boot into F15 (2.6.40.6-0) just fine.

I got around the issue with the preupgrade environment by disabling USB in the BIOS. Once I did that, cciss loaded fine and I had my RAID controller back. And once the upgrade completed, F16 booted fine. But once I re-enabled USB in the BIOS, I can no longer boot--because it can't find any drives.

I've tried booting with irqpoll, noapic, pci=nobios and pci=biosirq. None had any effect. Also tried playing with the IRQ settings in the BIOS with no luck at all--the IRQ of the Smart Array 6i is most definitely tied to one of the USB controllers and any change to one changes the other.

Any thoughts on how to proceed? Is there something else I can try or a workaround? This particular system is useless to me without USB.

I'll try to get the exact wording of what I see in dmesg tonight when I get home--was just hoping someone might know exactly what I am talking about.

Thanks!

John VV · 11-10-2011, 02:55 PM

upgrades and "preupgrade" do not always work well
there is almost always old files that need removing , kernel moduals that need rebuilding
programs that are still installed from the last fedora
programs that are NOT used in the new fedora that are still installed
programs that are in conflict with the old programs still installed

do a 100% clean new install of 16 after reformating the drive .

bradycl_84043 · 11-10-2011, 03:03 PM

Well, that was my thought, hence attempting to do a clean install from the DVD. Unfortunately, booting into the install DVD for Fedora 16 itself has the same issue. It makes it into anaconda, but sees no drives once it gets there. Dropping to a prompt from Alt-F1 and examining dmesg shows the exact same problem with IRQ 19 being unavailable for cciss if USB is enabled in the BIOS. This is what leads me to the kernel--again, both my Fedora 15 install and the Fedora 15 DVD boot with no problems.

Come to think of it, I'll post a dmesg from both a successful F15 DVD boot and an unsuccessful F16 DVD boot when I get home tonight. Maybe that well help someone shed some light?

bradycl_84043 · 11-10-2011, 11:46 PM

Okay... here is the dmesg of a boot into rescue mode from an FC15 Disc. Note that the CCISS driver loads fine into IRQ 51.

Code:

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.38.6-26.rc1.fc15.x86_64 (mockbuild@x86-04.phx2.fedoraproject.org) (gcc version 4.6.0 20110428 (Red Hat 4.6.0-6) (GCC) ) #1 SMP Mon May 9 20:45:15 UTC 2011
[    0.000000] Command line: initrd=initrd.img rescue BOOT_IMAGE=vmlinuz 
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
[    0.000000]  BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 00000000dfff3000 (usable)
[    0.000000]  BIOS-e820: 00000000dfff3000 - 00000000dfffb000 (ACPI data)
[    0.000000]  BIOS-e820: 00000000dfffb000 - 00000000e0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fed00000 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
[    0.000000]  BIOS-e820: 00000000ffc00000 - 0000000100000000 (reserved)
[    0.000000]  BIOS-e820: 0000000100000000 - 000000021bfff000 (usable)
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] DMI 2.3 present.
[    0.000000] DMI: HP ProLiant DL380 G4, BIOS P51 07/19/2007
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[    0.000000] No AGP bridge found
[    0.000000] last_pfn = 0x21bfff max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: write-back
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-C7FFF write-protect
[    0.000000]   C8000-E7FFF uncachable
[    0.000000]   E8000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 0E0000000 mask FE0000000 uncachable
[    0.000000]   1 disabled
[    0.000000]   2 disabled
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] last_pfn = 0xdfff3 max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [ffff8800000f4f80] f4f80
[    0.000000] initial memory mapped : 0 - 20000000
[    0.000000] init_memory_mapping: 0000000000000000-00000000dfff3000
[    0.000000]  0000000000 - 00dfe00000 page 2M
[    0.000000]  00dfe00000 - 00dfff3000 page 4k
[    0.000000] kernel direct mapping tables up to dfff3000 @ 1fffa000-20000000
[    0.000000] init_memory_mapping: 0000000100000000-000000021bfff000
[    0.000000]  0100000000 - 021be00000 page 2M
[    0.000000]  021be00000 - 021bfff000 page 4k
[    0.000000] kernel direct mapping tables up to 21bfff000 @ dffe8000-dfff3000
[    0.000000] RAMDISK: 7a1e3000 - 7ffff000
[    0.000000] ACPI: RSDP 00000000000f4f00 00024 (v02 HP    )
[    0.000000] ACPI: XSDT 00000000dfff3300 00044 (v01 HP     P51      00000002   Ò? 0000162E)
[    0.000000] ACPI: FACP 00000000dfff3380 000F4 (v03 HP     P51      00000002   Ò? 0000162E)
[    0.000000] ACPI Warning: Invalid length for Pm1aControlBlock: 32, using default 16 (20110112/tbfadt-607)
[    0.000000] ACPI: DSDT 00000000dfff3480 02DAB (v01 HP         DSDT 00000001 INTL 20030228)
[    0.000000] ACPI: FACS 00000000dfff3100 00040
[    0.000000] ACPI: SPCR 00000000dfff3140 00050 (v01 HP     SPCRRBSU 00000001   Ò? 0000162E)
[    0.000000] ACPI: MCFG 00000000dfff31c0 0003C (v01 HP     ProLiant 00000001      00000000)
[    0.000000] ACPI: APIC 00000000dfff3200 000C2 (v01 HP     00000083 00000002      00000000)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at 0000000000000000-000000021bfff000
[    0.000000] Initmem setup node 0 0000000000000000-000000021bfff000
[    0.000000]   NODE_DATA [000000021bfeb000 - 000000021bffefff]
[    0.000000]  [ffffea0000000000-ffffea00077fffff] PMD -> [ffff880213e00000-ffff88021affffff] on node 0
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   DMA32    0x00001000 -> 0x00100000
[    0.000000]   Normal   0x00100000 -> 0x0021bfff
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[3] active PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x000dfff3
[    0.000000]     0: 0x00100000 -> 0x0021bfff
[    0.000000] On node 0 totalpages: 2080641
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 6 pages reserved
[    0.000000]   DMA zone: 3921 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 14280 pages used for memmap
[    0.000000]   DMA32 zone: 899115 pages, LIFO batch:31
[    0.000000]   Normal zone: 15904 pages used for memmap
[    0.000000]   Normal zone: 1147359 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x908
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x04] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x06] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x05] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: IOAPIC (id[0x09] address[0xfec80000] gsi_base[24])
[    0.000000] IOAPIC[1]: apic_id 9, version 32, address 0xfec80000, GSI 24-47
[    0.000000] ACPI: IOAPIC (id[0x0a] address[0xfec80400] gsi_base[48])
[    0.000000] IOAPIC[2]: apic_id 10, version 32, address 0xfec80400, GSI 48-71
[    0.000000] ACPI: IOAPIC (id[0x0b] address[0xfec84000] gsi_base[72])
[    0.000000] IOAPIC[3]: apic_id 11, version 32, address 0xfec84000, GSI 72-95
[    0.000000] ACPI: IOAPIC (id[0x0c] address[0xfec84400] gsi_base[96])
[    0.000000] IOAPIC[4]: apic_id 12, version 32, address 0xfec84400, GSI 96-119
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] SMP: Allowing 8 CPUs, 4 hotplug CPUs
[    0.000000] nr_irqs_gsi: 136
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[    0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[    0.000000] PM: Registered nosave memory: 00000000dfff3000 - 00000000dfffb000
[    0.000000] PM: Registered nosave memory: 00000000dfffb000 - 00000000e0000000
[    0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000fec00000
[    0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fed00000
[    0.000000] PM: Registered nosave memory: 00000000fed00000 - 00000000fee00000
[    0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee10000
[    0.000000] PM: Registered nosave memory: 00000000fee10000 - 00000000ffc00000
[    0.000000] PM: Registered nosave memory: 00000000ffc00000 - 0000000100000000
[    0.000000] Allocating PCI resources starting at e0000000 (gap: e0000000:1ec00000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:8 nr_node_ids:1
[    0.000000] PERCPU: Embedded 28 pages/cpu @ffff8800dfc00000 s83200 r8192 d23296 u262144
[    0.000000] pcpu-alloc: s83200 r8192 d23296 u262144 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 2050395
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: initrd=initrd.img rescue BOOT_IMAGE=vmlinuz 
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Checking aperture...
[    0.000000] No AGP bridge found
[    0.000000] Calgary: detecting Calgary via BIOS EBDA area
[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000000] Memory: 8028100k/8847356k available (4599k kernel code, 524792k absent, 294464k reserved, 6924k data, 948k init)
[    0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] 	RCU-based detection of stalled CPUs is disabled.
[    0.000000] NR_IRQS:16640 nr_irqs:2048 16
[    0.000000] Extended CMOS year: 2000
[    0.000000] spurious 8259A interrupt: IRQ7.
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] allocated 83886080 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 3399.858 MHz processor.
[    0.003006] Calibrating delay loop (skipped), value calculated using timer frequency.. 6799.71 BogoMIPS (lpj=3399858)
[    0.003436] pid_max: default: 32768 minimum: 301
[    0.003683] Security Framework initialized
[    0.003905] SELinux:  Initializing.
[    0.004022] SELinux:  Starting in permissive mode
[    0.006135] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[    0.013105] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.016179] Mount-cache hash table entries: 256
[    0.016694] Initializing cgroup subsys ns
[    0.016914] ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup.
[    0.017011] Initializing cgroup subsys cpuacct
[    0.017227] Initializing cgroup subsys memory
[    0.017473] Initializing cgroup subsys devices
[    0.018006] Initializing cgroup subsys freezer
[    0.018223] Initializing cgroup subsys net_cls
[    0.018433] Initializing cgroup subsys blkio
[    0.018698] CPU: Physical Processor ID: 0
[    0.018910] CPU: Processor Core ID: 0
[    0.019006] mce: CPU supports 4 MCE banks
[    0.019228] CPU0: Thermal monitoring enabled (TM1)
[    0.019428] using mwait in idle threads.
[    0.020553] ACPI: Core revision 20110112
[    0.024023] ftrace: allocating 23793 entries in 94 pages
[    0.026101] Setting APIC routing to flat
[    0.026692] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
[    0.037330] CPU0: Intel(R) Xeon(TM) CPU 3.40GHz stepping 01
[    0.037997] Performance Events: Netburst events, Broken PMU hardware detected, using software events only.
[    0.038092] NMI watchdog disabled (cpu0): hardware events not enabled
[    0.038503] Booting Node   0, Processors  #1
[    0.110016] NMI watchdog disabled (cpu1): hardware events not enabled
[    0.110559]  #2
[    0.182016] NMI watchdog disabled (cpu2): hardware events not enabled
[    0.182585]  #3
[    0.253987] NMI watchdog disabled (cpu3): hardware events not enabled
[    0.254393] Brought up 4 CPUs
[    0.254603] Total of 4 processors activated (27196.98 BogoMIPS).
[    0.255993] sizeof(vma)=184 bytes
[    0.255998] sizeof(page)=56 bytes
[    0.256001] sizeof(inode)=600 bytes
[    0.256003] sizeof(dentry)=192 bytes
[    0.256005] sizeof(ext3inode)=816 bytes
[    0.256007] sizeof(ext4inode)=920 bytes
[    0.256009] sizeof(buffer_head)=104 bytes
[    0.256011] sizeof(skbuff)=240 bytes
[    0.256013] sizeof(task_struct)=5920 bytes
[    0.256127] devtmpfs: initialized
[    0.260840] atomic64 test passed for x86-64 platform with CX8 and with SSE
[    0.261005] Time:  1:41:04  Date: 07/20/07
[    0.261278] NET: Registered protocol family 16
[    0.261755] ACPI: bus type pci registered
[    0.262069] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.262437] PCI: Intel Corporation E7520 Memory Controller Hub with MMCONFIG support
[    0.262826] PCI: not using MMCONFIG
[    0.262974] PCI: Using configuration type 1 for base access
[    0.263197] PCI: HP ProLiant DL380 detected, enabling pci=bfsort.
[    0.263644] mtrr: your CPUs had inconsistent fixed MTRR settings
[    0.263972] mtrr: probably your BIOS does not setup all CPUs.
[    0.264190] mtrr: corrected configuration.
[    0.266029] bio: create slab <bio-0> at 0
[    0.267575] ACPI: EC: Look up EC in DSDT
[    0.269697] ACPI: Interpreter enabled
[    0.269914] ACPI: (supports S0 S4 S5)
[    0.270288] ACPI: Using IOAPIC for interrupt routing
[    0.278092] ACPI: No dock devices found.
[    0.278306] HEST: Table not found.
[    0.278512] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[    0.279001] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-7f])
[    0.279395] pci_root PNP0A03:00: host bridge window [io  0x0000-0x0cf7] (ignored)
[    0.279400] pci_root PNP0A03:00: host bridge window [io  0x0d00-0xffff] (ignored)
[    0.279403] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[    0.279407] pci_root PNP0A03:00: host bridge window [mem 0xe0000000-0xfebfffff] (ignored)
[    0.279423] pci 0000:00:00.0: [8086:3590] type 0 class 0x000600
[    0.279500] pci 0000:00:02.0: [8086:3595] type 1 class 0x000604
[    0.279551] pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
[    0.279556] pci 0000:00:02.0: PME# disabled
[    0.279588] pci 0000:00:06.0: [8086:3599] type 1 class 0x000604
[    0.279639] pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
[    0.279644] pci 0000:00:06.0: PME# disabled
[    0.279695] pci 0000:00:1d.0: [8086:24d2] type 0 class 0x000c03
[    0.279747] pci 0000:00:1d.0: reg 20: [io  0x3000-0x301f]
[    0.279787] pci 0000:00:1d.1: [8086:24d4] type 0 class 0x000c03
[    0.279838] pci 0000:00:1d.1: reg 20: [io  0x3020-0x303f]
[    0.279877] pci 0000:00:1d.2: [8086:24d7] type 0 class 0x000c03
[    0.279928] pci 0000:00:1d.2: reg 20: [io  0x3040-0x305f]
[    0.279975] pci 0000:00:1d.3: [8086:24de] type 0 class 0x000c03
[    0.280026] pci 0000:00:1d.3: reg 20: [io  0x3060-0x307f]
[    0.280074] pci 0000:00:1e.0: [8086:244e] type 1 class 0x000604
[    0.280127] pci 0000:00:1f.0: [8086:24d0] type 0 class 0x000601
[    0.280203] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[    0.280228] pci 0000:00:1f.1: [8086:24db] type 0 class 0x000101
[    0.280244] pci 0000:00:1f.1: reg 10: [io  0x01f0-0x01f7]
[    0.280256] pci 0000:00:1f.1: reg 14: [io  0x03f4-0x03f7]
[    0.280267] pci 0000:00:1f.1: reg 18: [io  0x0170-0x0177]
[    0.280279] pci 0000:00:1f.1: reg 1c: [io  0x0374-0x0377]
[    0.280290] pci 0000:00:1f.1: reg 20: [io  0x0500-0x050f]
[    0.280302] pci 0000:00:1f.1: reg 24: [mem 0x00000000-0x000003ff]
[    0.280383] pci 0000:02:00.0: [8086:0329] type 1 class 0x000604
[    0.280401] pci 0000:02:00.0: PXH quirk detected; SHPC device MSI disabled
[    0.280668] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[    0.280673] pci 0000:02:00.0: PME# disabled
[    0.280696] pci 0000:02:00.2: [8086:032a] type 1 class 0x000604
[    0.280714] pci 0000:02:00.2: PXH quirk detected; SHPC device MSI disabled
[    0.280994] pci 0000:02:00.2: PME# supported from D0 D3hot D3cold
[    0.280998] pci 0000:02:00.2: PME# disabled
[    0.281016] pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.281415] pci 0000:00:02.0: PCI bridge to [bus 02-04]
[    0.281628] pci 0000:00:02.0:   bridge window [io  0x4000-0x4fff]
[    0.281633] pci 0000:00:02.0:   bridge window [mem 0xf7e00000-0xf7ffffff]
[    0.281640] pci 0000:00:02.0:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.281691] pci 0000:03:01.0: [14e4:1648] type 0 class 0x000200
[    0.281713] pci 0000:03:01.0: reg 10: [mem 0xf7ef0000-0xf7efffff 64bit]
[    0.281774] pci 0000:03:01.0: PME# supported from D3hot D3cold
[    0.281779] pci 0000:03:01.0: PME# disabled
[    0.281807] pci 0000:03:01.1: [14e4:1648] type 0 class 0x000200
[    0.281828] pci 0000:03:01.1: reg 10: [mem 0x00000000-0x0000ffff 64bit]
[    0.281889] pci 0000:03:01.1: PME# supported from D3hot D3cold
[    0.281893] pci 0000:03:01.1: PME# disabled
[    0.281943] pci 0000:02:00.0: PCI bridge to [bus 03-03]
[    0.281973] pci 0000:02:00.0:   bridge window [io  0xf000-0x0000] (disabled)
[    0.281979] pci 0000:02:00.0:   bridge window [mem 0xf7e00000-0xf7efffff]
[    0.281986] pci 0000:02:00.0:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.282041] pci 0000:04:03.0: [0e11:0046] type 0 class 0x000104
[    0.282065] pci 0000:04:03.0: reg 10: [mem 0xf7ff0000-0xf7ff1fff 64bit]
[    0.282075] pci 0000:04:03.0: reg 18: [io  0x4000-0x40ff]
[    0.282089] pci 0000:04:03.0: reg 1c: [mem 0xf7f80000-0xf7fbffff 64bit]
[    0.282107] pci 0000:04:03.0: reg 30: [mem 0x00000000-0x0003ffff pref]
[    0.282130] pci 0000:04:03.0: supports D1
[    0.282171] pci 0000:02:00.2: PCI bridge to [bus 04-04]
[    0.282386] pci 0000:02:00.2:   bridge window [io  0x4000-0x4fff]
[    0.282391] pci 0000:02:00.2:   bridge window [mem 0xf7f00000-0xf7ffffff]
[    0.282398] pci 0000:02:00.2:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.282454] pci 0000:05:00.0: [8086:0329] type 1 class 0x000604
[    0.282471] pci 0000:05:00.0: PXH quirk detected; SHPC device MSI disabled
[    0.282745] pci 0000:05:00.0: PME# supported from D0 D3hot D3cold
[    0.282749] pci 0000:05:00.0: PME# disabled
[    0.282976] pci 0000:05:00.2: [8086:032a] type 1 class 0x000604
[    0.282994] pci 0000:05:00.2: PXH quirk detected; SHPC device MSI disabled
[    0.283265] pci 0000:05:00.2: PME# supported from D0 D3hot D3cold
[    0.283270] pci 0000:05:00.2: PME# disabled
[    0.283287] pci 0000:05:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.283664] pci 0000:00:06.0: PCI bridge to [bus 05-0c]
[    0.283882] pci 0000:00:06.0:   bridge window [io  0xf000-0x0000] (disabled)
[    0.283887] pci 0000:00:06.0:   bridge window [mem 0xf8000000-0xfdffffff]
[    0.283894] pci 0000:00:06.0:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.283943] pci 0000:06:01.0: [14f1:8800] type 0 class 0x000400
[    0.283971] pci 0000:06:01.0: reg 10: [mem 0xfd000000-0xfdffffff]
[    0.284069] pci 0000:06:01.1: [14f1:8801] type 0 class 0x000480
[    0.284088] pci 0000:06:01.1: reg 10: [mem 0xfc000000-0xfcffffff]
[    0.284174] pci 0000:06:01.2: [14f1:8802] type 0 class 0x000480
[    0.284193] pci 0000:06:01.2: reg 10: [mem 0xfb000000-0xfbffffff]
[    0.284288] pci 0000:06:02.0: [14f1:8800] type 0 class 0x000400
[    0.284310] pci 0000:06:02.0: reg 10: [mem 0xfa000000-0xfaffffff]
[    0.284401] pci 0000:06:02.1: [14f1:8801] type 0 class 0x000480
[    0.284419] pci 0000:06:02.1: reg 10: [mem 0xf9000000-0xf9ffffff]
[    0.284503] pci 0000:06:02.2: [14f1:8802] type 0 class 0x000480
[    0.284521] pci 0000:06:02.2: reg 10: [mem 0xf8000000-0xf8ffffff]
[    0.284638] pci 0000:05:00.0: PCI bridge to [bus 06-09]
[    0.284859] pci 0000:05:00.0:   bridge window [io  0xf000-0x0000] (disabled)
[    0.284864] pci 0000:05:00.0:   bridge window [mem 0xf8000000-0xfdffffff]
[    0.284870] pci 0000:05:00.0:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.284940] pci 0000:05:00.2: PCI bridge to [bus 0a-0c]
[    0.284973] pci 0000:05:00.2:   bridge window [io  0xf000-0x0000] (disabled)
[    0.284978] pci 0000:05:00.2:   bridge window [mem 0xfff00000-0x000fffff] (disabled)
[    0.284985] pci 0000:05:00.2:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.285028] pci 0000:01:03.0: [1002:4752] type 0 class 0x000300
[    0.285047] pci 0000:01:03.0: reg 10: [mem 0xf6000000-0xf6ffffff]
[    0.285059] pci 0000:01:03.0: reg 14: [io  0x2000-0x20ff]
[    0.285071] pci 0000:01:03.0: reg 18: [mem 0xf5ff0000-0xf5ff0fff]
[    0.285109] pci 0000:01:03.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[    0.285132] pci 0000:01:03.0: supports D1 D2
[    0.285152] pci 0000:01:04.0: [0e11:b203] type 0 class 0x000880
[    0.285170] pci 0000:01:04.0: reg 10: [io  0x1800-0x18ff]
[    0.285181] pci 0000:01:04.0: reg 14: [mem 0xf5fe0000-0xf5fe01ff]
[    0.285259] pci 0000:01:04.2: [0e11:b204] type 0 class 0x000880
[    0.285279] pci 0000:01:04.2: reg 10: [io  0x2400-0x24ff]
[    0.285291] pci 0000:01:04.2: reg 14: [mem 0xf5fd0000-0xf5fd07ff]
[    0.285303] pci 0000:01:04.2: reg 18: [mem 0xf5fc0000-0xf5fc1fff]
[    0.285314] pci 0000:01:04.2: reg 1c: [mem 0xf5f00000-0xf5f7ffff]
[    0.285345] pci 0000:01:04.2: reg 30: [mem 0x00000000-0x0000ffff pref]
[    0.285368] pci 0000:01:04.2: PME# supported from D0 D3hot D3cold
[    0.285374] pci 0000:01:04.2: PME# disabled
[    0.285424] pci 0000:00:1e.0: PCI bridge to [bus 01-01] (subtractive decode)
[    0.285649] pci 0000:00:1e.0:   bridge window [io  0x1000-0x2fff]
[    0.285655] pci 0000:00:1e.0:   bridge window [mem 0xf5f00000-0xf6ffffff]
[    0.285661] pci 0000:00:1e.0:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.285664] pci 0000:00:1e.0:   bridge window [io  0x0000-0xffff] (subtractive decode)
[    0.285668] pci 0000:00:1e.0:   bridge window [mem 0x00000000-0xfffffffff] (subtractive decode)
[    0.285689] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.286013] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.IP2P._PRT]
[    0.286080] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PTA0._PRT]
[    0.286144] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PTA0.PCXA._PRT]
[    0.286204] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PTA0.PCXB._PRT]
[    0.286249] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PTC0._PRT]
[    0.286307] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PTC0.PCXC._PRT]
[    0.286468] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PTC0.PCXD._PRT]
[    0.300533] ACPI: PCI Interrupt Link [LNKA] (IRQs *5 7 10 11)
[    0.301034] ACPI: PCI Interrupt Link [LNKB] (IRQs *5 7 10 11)
[    0.301547] ACPI: PCI Interrupt Link [LNKC] (IRQs *5 7 10 11)
[    0.302029] ACPI: PCI Interrupt Link [LNKD] (IRQs *5 7 10 11)
[    0.302542] ACPI: PCI Interrupt Link [LNKE] (IRQs 5 7 10 11) *0, disabled.
[    0.303326] ACPI: PCI Interrupt Link [LNKF] (IRQs *5 7 10 11)
[    0.303836] ACPI: PCI Interrupt Link [LNKG] (IRQs *5 7 10 11)
[    0.304363] ACPI: PCI Interrupt Link [LNKH] (IRQs *5 7 10 11)
[    0.305049] vgaarb: device added: PCI:0000:01:03.0,decodes=io+mem,owns=none,locks=none
[    0.305438] vgaarb: loaded
[    0.305786] SCSI subsystem initialized
[    0.306014] libata version 3.00 loaded.
[    0.306093] usbcore: registered new interface driver usbfs
[    0.306328] usbcore: registered new interface driver hub
[    0.306551] usbcore: registered new device driver usb
[    0.307021] PCI: Using ACPI for IRQ routing
[    0.307220] PCI: pci_cache_line_size set to 64 bytes
[    0.307350] reserve RAM buffer: 000000000009f400 - 000000000009ffff 
[    0.307354] reserve RAM buffer: 00000000dfff3000 - 00000000dfffffff 
[    0.307357] reserve RAM buffer: 000000021bfff000 - 000000021bffffff 
[    0.307528] NetLabel: Initializing
[    0.307740] NetLabel:  domain hash size = 128
[    0.307967] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.308198] NetLabel:  unlabeled traffic allowed by default
[    0.308583] hpet clockevent registered
[    0.308589] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.308822] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.309270] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.314000] Switching to clocksource hpet
[    0.314824] Switched to NOHz mode on CPU #0
[    0.314583] Switched to NOHz mode on CPU #1
[    0.314626] Switched to NOHz mode on CPU #3
[    0.314703] Switched to NOHz mode on CPU #2
[    0.329866] pnp: PnP ACPI init
[    0.330114] ACPI: bus type pnp registered
[    0.330451] pnp 00:00: [bus 00-7f]
[    0.330455] pnp 00:00: [io  0x0000-0x0cf7 window]
[    0.330459] pnp 00:00: [io  0x0d00-0xffff window]
[    0.330462] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[    0.330466] pnp 00:00: [mem 0xe0000000-0xfebfffff window]
[    0.330545] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
[    0.332302] pnp 00:01: [io  0x0070-0x0077]
[    0.332306] pnp 00:01: [io  0x0408-0x040f]
[    0.332309] pnp 00:01: [io  0x04d0-0x04d1]
[    0.332311] pnp 00:01: [io  0x0020-0x003f]
[    0.332314] pnp 00:01: [io  0x00a0-0x00bf]
[    0.332317] pnp 00:01: [io  0x0090-0x009f]
[    0.332319] pnp 00:01: [io  0x0050-0x0053]
[    0.332322] pnp 00:01: [io  0x0700-0x071f]
[    0.332324] pnp 00:01: [io  0x0800-0x083f]
[    0.332327] pnp 00:01: [io  0x0900-0x097f]
[    0.332330] pnp 00:01: [io  0x0010-0x001f]
[    0.332332] pnp 00:01: [io  0x0c80-0x0c83]
[    0.332335] pnp 00:01: [io  0x0cd4-0x0cd7]
[    0.332337] pnp 00:01: [io  0x0f50-0x0f58]
[    0.332340] pnp 00:01: [io  0x02f8-0x02ff]
[    0.332343] pnp 00:01: [mem 0xe0000000-0xefffffff]
[    0.332454] system 00:01: [io  0x0408-0x040f] has been reserved
[    0.332674] system 00:01: [io  0x04d0-0x04d1] has been reserved
[    0.332895] system 00:01: [io  0x0700-0x071f] has been reserved
[    0.333109] system 00:01: [io  0x0800-0x083f] has been reserved
[    0.333329] system 00:01: [io  0x0900-0x097f] has been reserved
[    0.333553] system 00:01: [io  0x0c80-0x0c83] has been reserved
[    0.333775] system 00:01: [io  0x0cd4-0x0cd7] has been reserved
[    0.333983] system 00:01: [io  0x0f50-0x0f58] has been reserved
[    0.334207] system 00:01: [io  0x02f8-0x02ff] has been reserved
[    0.334426] system 00:01: [mem 0xe0000000-0xefffffff] has been reserved
[    0.334648] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.334668] pnp 00:02: [dma 7]
[    0.334672] pnp 00:02: [io  0x0000-0x000f]
[    0.334675] pnp 00:02: [io  0x0080-0x008f]
[    0.334677] pnp 00:02: [io  0x00c0-0x00df]
[    0.334726] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.334741] pnp 00:03: [io  0x0061]
[    0.334798] pnp 00:03: Plug and Play ACPI device, IDs PNP0800 (active)
[    0.334814] pnp 00:04: [io  0x0060]
[    0.334817] pnp 00:04: [io  0x0064]
[    0.334834] pnp 00:04: [irq 1]
[    0.334884] pnp 00:04: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.334904] pnp 00:05: [irq 12]
[    0.334958] pnp 00:05: Plug and Play ACPI device, IDs PNP0f13 PNP0f0e (active)

Continued...

bradycl_84043 · 11-10-2011, 11:47 PM

...Continued from above for successful CCISS load on boot from F15 disc.

Code:

[    0.334974] pnp 00:06: [io  0x002e-0x002f]
[    0.334977] pnp 00:06: [io  0x004e-0x004f]
[    0.334980] pnp 00:06: [io  0x0220-0x025f]
[    0.334983] pnp 00:06: [io  0x0280-0x029f]
[    0.335045] pnp 00:06: Plug and Play ACPI device, IDs PNP0a06 (active)
[    0.335183] pnp 00:07: Plug and Play ACPI device, IDs PNP0501 PNP0500 (disabled)
[    0.335300] pnp 00:08: Plug and Play ACPI device, IDs PNP0700 (disabled)
[    0.335552] pnp: PnP ACPI: found 9 devices
[    0.335765] ACPI: ACPI bus type pnp unregistered
[    0.344064] pci 0000:00:02.0: BAR 15: assigned [mem 0xf0000000-0xf00fffff pref]
[    0.344451] pci 0000:00:1e.0: BAR 15: assigned [mem 0xf0100000-0xf01fffff pref]
[    0.344832] pci 0000:00:1f.1: BAR 5: assigned [mem 0xf0200000-0xf02003ff]
[    0.345051] pci 0000:00:1f.1: BAR 5: set to [mem 0xf0200000-0xf02003ff] (PCI address [0xf0200000-0xf02003ff])
[    0.345457] pci 0000:02:00.2: BAR 15: assigned [mem 0xf0000000-0xf00fffff pref]
[    0.345856] pci 0000:03:01.1: BAR 0: assigned [mem 0xf7e00000-0xf7e0ffff 64bit]
[    0.346237] pci 0000:03:01.1: BAR 0: set to [mem 0xf7e00000-0xf7e0ffff 64bit] (PCI address [0xf7e00000-0xf7e0ffff])
[    0.346629] pci 0000:02:00.0: PCI bridge to [bus 03-03]
[    0.346844] pci 0000:02:00.0:   bridge window [io  disabled]
[    0.347060] pci 0000:02:00.0:   bridge window [mem 0xf7e00000-0xf7efffff]
[    0.347279] pci 0000:02:00.0:   bridge window [mem pref disabled]
[    0.347506] pci 0000:04:03.0: BAR 6: assigned [mem 0xf0000000-0xf003ffff pref]
[    0.347887] pci 0000:02:00.2: PCI bridge to [bus 04-04]
[    0.348102] pci 0000:02:00.2:   bridge window [io  0x4000-0x4fff]
[    0.348318] pci 0000:02:00.2:   bridge window [mem 0xf7f00000-0xf7ffffff]
[    0.348527] pci 0000:02:00.2:   bridge window [mem 0xf0000000-0xf00fffff pref]
[    0.348894] pci 0000:00:02.0: PCI bridge to [bus 02-04]
[    0.349308] pci 0000:00:02.0:   bridge window [io  0x4000-0x4fff]
[    0.349531] pci 0000:00:02.0:   bridge window [mem 0xf7e00000-0xf7ffffff]
[    0.349756] pci 0000:00:02.0:   bridge window [mem 0xf0000000-0xf00fffff pref]
[    0.350140] pci 0000:05:00.0: PCI bridge to [bus 06-09]
[    0.350353] pci 0000:05:00.0:   bridge window [io  disabled]
[    0.350574] pci 0000:05:00.0:   bridge window [mem 0xf8000000-0xfdffffff]
[    0.350791] pci 0000:05:00.0:   bridge window [mem pref disabled]
[    0.351000] pci 0000:05:00.2: PCI bridge to [bus 0a-0c]
[    0.351227] pci 0000:05:00.2:   bridge window [io  disabled]
[    0.351447] pci 0000:05:00.2:   bridge window [mem disabled]
[    0.351668] pci 0000:05:00.2:   bridge window [mem pref disabled]
[    0.351891] pci 0000:00:06.0: PCI bridge to [bus 05-0c]
[    0.352102] pci 0000:00:06.0:   bridge window [io  disabled]
[    0.352326] pci 0000:00:06.0:   bridge window [mem 0xf8000000-0xfdffffff]
[    0.352544] pci 0000:00:06.0:   bridge window [mem pref disabled]
[    0.352764] pci 0000:01:03.0: BAR 6: assigned [mem 0xf0100000-0xf011ffff pref]
[    0.353146] pci 0000:01:04.2: BAR 6: assigned [mem 0xf0120000-0xf012ffff pref]
[    0.353537] pci 0000:00:1e.0: PCI bridge to [bus 01-01]
[    0.353756] pci 0000:00:1e.0:   bridge window [io  0x1000-0x2fff]
[    0.353967] pci 0000:00:1e.0:   bridge window [mem 0xf5f00000-0xf6ffffff]
[    0.354196] pci 0000:00:1e.0:   bridge window [mem 0xf0100000-0xf01fffff pref]
[    0.354614] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.354836] pci 0000:00:02.0: setting latency timer to 64
[    0.354852] pci 0000:02:00.0: setting latency timer to 64
[    0.354861] pci 0000:02:00.2: setting latency timer to 64
[    0.354869] pci 0000:00:06.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.355080] pci 0000:00:06.0: setting latency timer to 64
[    0.355096] pci 0000:05:00.0: setting latency timer to 64
[    0.355104] pci 0000:05:00.2: setting latency timer to 64
[    0.355113] pci 0000:00:1e.0: setting latency timer to 64
[    0.355118] pci_bus 0000:00: resource 0 [io  0x0000-0xffff]
[    0.355121] pci_bus 0000:00: resource 1 [mem 0x00000000-0xfffffffff]
[    0.355125] pci_bus 0000:02: resource 0 [io  0x4000-0x4fff]
[    0.355128] pci_bus 0000:02: resource 1 [mem 0xf7e00000-0xf7ffffff]
[    0.355131] pci_bus 0000:02: resource 2 [mem 0xf0000000-0xf00fffff pref]
[    0.355135] pci_bus 0000:03: resource 1 [mem 0xf7e00000-0xf7efffff]
[    0.355138] pci_bus 0000:04: resource 0 [io  0x4000-0x4fff]
[    0.355141] pci_bus 0000:04: resource 1 [mem 0xf7f00000-0xf7ffffff]
[    0.355144] pci_bus 0000:04: resource 2 [mem 0xf0000000-0xf00fffff pref]
[    0.355147] pci_bus 0000:05: resource 1 [mem 0xf8000000-0xfdffffff]
[    0.355150] pci_bus 0000:06: resource 1 [mem 0xf8000000-0xfdffffff]
[    0.355154] pci_bus 0000:01: resource 0 [io  0x1000-0x2fff]
[    0.355157] pci_bus 0000:01: resource 1 [mem 0xf5f00000-0xf6ffffff]
[    0.355160] pci_bus 0000:01: resource 2 [mem 0xf0100000-0xf01fffff pref]
[    0.355164] pci_bus 0000:01: resource 4 [io  0x0000-0xffff]
[    0.355167] pci_bus 0000:01: resource 5 [mem 0x00000000-0xfffffffff]
[    0.355212] NET: Registered protocol family 2
[    0.355937] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.359594] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[    0.365823] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.366747] TCP: Hash tables configured (established 524288 bind 65536)
[    0.366964] TCP reno registered
[    0.367247] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[    0.367585] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[    0.368131] NET: Registered protocol family 1
[    0.368471] pci 0000:02:00.0: rerouting interrupts for [8086:0329]
[    0.368651] pci 0000:02:00.2: rerouting interrupts for [8086:032a]
[    0.368833] pci 0000:05:00.0: rerouting interrupts for [8086:0329]
[    0.369020] pci 0000:05:00.2: rerouting interrupts for [8086:032a]
[    0.369212] PCI: CLS 64 bytes, default 64
[    0.369318] Trying to unpack rootfs image as initramfs...
[   17.842637] Freeing initrd memory: 96368k freed
[   17.908050] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[   17.908226] Placing 64MB software IO TLB between ffff8800dbc00000 - ffff8800dfc00000
[   17.908519] software IO TLB at phys 0xdbc00000 - 0xdfc00000
[   17.908866] platform rtc_cmos: registered platform RTC device (no PNP device found)
[   17.910144] Intel AES-NI instructions are not detected.
[   17.910532] audit: initializing netlink socket (disabled)
[   17.910721] type=2000 audit(1184895680.909:1): initialized
[   17.926384] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[   17.930763] VFS: Disk quotas dquot_6.5.2
[   17.931024] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[   17.931991] msgmni has been set to 15868
[   17.932265] SELinux:  Registering netfilter hooks
[   17.932765] NET: Registered protocol family 38
[   17.933042] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[   17.933397] io scheduler noop registered
[   17.933568] io scheduler deadline registered
[   17.933797] io scheduler cfq registered (default)
[   17.934312] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   17.934524] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[   17.934697] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[   17.935213] acpiphp: Slot [0] registered
[   17.936261] acpiphp: Slot [4294967295] registered
[   17.937641] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[   17.937945] ACPI: Power Button [PWRF]
[   17.939938] ACPI: acpi_idle registered with cpuidle
[   17.943264] thermal LNXTHERM:00: registered as thermal_zone0
[   17.943438] ACPI: Thermal Zone [THM0] (8 C)
[   17.943630] ERST: Table is not found!
[   17.943976] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[   17.962494] serial 00:07: [irq 4]
[   17.962501] serial 00:07: [io  0x03f8-0x03ff]
[   17.962868] serial 00:07: activated
[   17.983577] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[   17.984226] Non-volatile memory driver v1.3
[   17.984400] Linux agpgart interface v0.103
[   17.986743] brd: module loaded
[   17.987938] loop: module loaded
[   17.988290] ata_piix 0000:00:1f.1: version 2.13
[   17.988301] ata_piix 0000:00:1f.1: enabling device (0005 -> 0007)
[   17.988479] ata_piix 0000:00:1f.1: can't derive routing for PCI INT A
[   17.988701] ata_piix 0000:00:1f.1: setting latency timer to 64
[   17.989299] scsi0 : ata_piix
[   17.989617] scsi1 : ata_piix
[   17.989865] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x500 irq 14
[   17.990055] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x508 irq 15
[   17.990355] Fixed MDIO Bus: probed
[   17.990682] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   17.990888] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   17.991110] uhci_hcd: USB Universal Host Controller Interface driver
[   17.991319] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   17.991503] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[   17.991508] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[   17.991777] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[   17.992171] uhci_hcd 0000:00:1d.0: irq 16, io base 0x00003000
[   17.992420] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[   17.992594] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   17.992897] usb usb1: Product: UHCI Host Controller
[   17.993268] usb usb1: Manufacturer: Linux 2.6.38.6-26.rc1.fc15.x86_64 uhci_hcd
[   17.993565] usb usb1: SerialNumber: 0000:00:1d.0
[   17.993914] hub 1-0:1.0: USB hub found
[   17.994095] hub 1-0:1.0: 2 ports detected
[   17.994421] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[   17.994596] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[   17.994601] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[   17.994841] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[   17.995230] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00003020
[   17.995456] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[   17.995632] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   17.995933] usb usb2: Product: UHCI Host Controller
[   17.999688] usb usb2: Manufacturer: Linux 2.6.38.6-26.rc1.fc15.x86_64 uhci_hcd
[   17.999992] usb usb2: SerialNumber: 0000:00:1d.1
[   18.000331] hub 2-0:1.0: USB hub found
[   18.000506] hub 2-0:1.0: 2 ports detected
[   18.000819] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[   18.001001] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[   18.001015] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[   18.001259] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[   18.001639] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00003040
[   18.001863] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[   18.002052] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   18.002359] usb usb3: Product: UHCI Host Controller
[   18.002531] usb usb3: Manufacturer: Linux 2.6.38.6-26.rc1.fc15.x86_64 uhci_hcd
[   18.002831] usb usb3: SerialNumber: 0000:00:1d.2
[   18.003164] hub 3-0:1.0: USB hub found
[   18.003338] hub 3-0:1.0: 2 ports detected
[   18.003618] uhci_hcd 0000:00:1d.3: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   18.003800] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[   18.003804] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[   18.004053] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[   18.004415] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00003060
[   18.004638] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[   18.004813] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   18.005127] usb usb4: Product: UHCI Host Controller
[   18.005302] usb usb4: Manufacturer: Linux 2.6.38.6-26.rc1.fc15.x86_64 uhci_hcd
[   18.005607] usb usb4: SerialNumber: 0000:00:1d.3
[   18.005931] hub 4-0:1.0: USB hub found
[   18.006116] hub 4-0:1.0: 2 ports detected
[   18.006483] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
[   18.008602] serio: i8042 KBD port at 0x60,0x64 irq 1
[   18.008797] serio: i8042 AUX port at 0x60,0x64 irq 12
[   18.009278] mousedev: PS/2 mouse device common for all mice
[   18.009782] rtc_cmos rtc_cmos: RTC can wake from S4
[   18.016157] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
[   18.016368] rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
[   18.016755] device-mapper: uevent: version 1.0.3
[   18.017103] device-mapper: ioctl: 4.19.1-ioctl (2011-01-07) initialised: dm-devel@redhat.com
[   18.017517] cpuidle: using governor ladder
[   18.017693] cpuidle: using governor menu
[   18.018214] usbcore: registered new interface driver usbhid
[   18.018392] usbhid: USB HID core driver
[   18.018610] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[   18.019035] ip_tables: (C) 2000-2006 Netfilter Core Team
[   18.019235] TCP cubic registered
[   18.019409] Initializing XFRM netlink socket
[   18.019608] NET: Registered protocol family 17
[   18.019815] Registering the dns_resolver key type
[   18.020218] PM: Hibernation image not present or could not be loaded.
[   18.020240] registered taskstats version 1
[   18.021137] IMA: No TPM chip found, activating TPM-bypass!
[   18.021799]   Magic number: 15:742:660
[   18.021996] block ram13: hash matches
[   18.022279] rtc_cmos rtc_cmos: setting system clock to 2007-07-20 01:41:22 UTC (1184895682)
[   18.022632] Initalizing network drop monitor service
[   18.042264] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[   18.144293] ata1.00: ATAPI: DVD-ROM DW-224E-R, K.AA, max UDMA/33
[   18.150171] ata1.00: configured for UDMA/33
[   18.152445] scsi 0:0:0:0: CD-ROM            TEAC     DVD-ROM DW-224ER K.AA PQ: 0 ANSI: 5
[   18.154422] sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray
[   18.154607] cdrom: Uniform CD-ROM driver Revision: 3.20
[   18.154972] sr 0:0:0:0: Attached scsi CD-ROM sr0
[   18.155101] sr 0:0:0:0: Attached scsi generic sg0 type 5
[   18.158748] Freeing unused kernel memory: 948k freed
[   18.159465] Write protecting the kernel read-only data: 10240k
[   18.170125] Freeing unused kernel memory: 1528k freed
[   18.182793] Freeing unused kernel memory: 1728k freed
[   18.296041] usb 1-1: new full speed USB device using uhci_hcd and address 2
[   18.330216] input: ImPS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio1/input/input2
[   18.439336] usb 1-1: New USB device found, idVendor=049f, idProduct=0048
[   18.439343] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[   18.439347] usb 1-1: Product: Virtual Management Device
[   18.439351] usb 1-1: Manufacturer: HP
[   18.446666] input: HP Virtual Management Device as /devices/pci0000:00/0000:00:1d.0/usb1/1-1/1-1:1.0/input/input3
[   18.446995] generic-usb 0003:049F:0048.0001: input,hidraw0: USB HID v1.01 Mouse [HP Virtual Management Device] on usb-0000:00:1d.0-1/input0
[   18.549033] usb 3-1: new full speed USB device using uhci_hcd and address 2
[   18.700755] usb 3-1: New USB device found, idVendor=cd12, idProduct=ef18
[   18.700760] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   18.700765] usb 3-1: Product: Flash Drive
[   18.700768] usb 3-1: Manufacturer: USB
[   18.700771] usb 3-1: SerialNumber: D0D770CF02556290
[   18.711837] usbcore: registered new interface driver uas
[   18.720692] Initializing USB Mass Storage driver...
[   18.720939] scsi2 : usb-storage 3-1:1.0
[   18.721233] usbcore: registered new interface driver usb-storage
[   18.721239] USB Mass Storage support registered.
[   18.910041] Refined TSC clocksource calibration: 3400.120 MHz.
[   18.910048] Switching to clocksource tsc
[   19.725652] scsi 2:0:0:0: Direct-Access     USB      Flash Disk       1.00 PQ: 0 ANSI: 2
[   19.727212] sd 2:0:0:0: Attached scsi generic sg1 type 0
[   19.731650] sd 2:0:0:0: [sda] 7900336 512-byte logical blocks: (4.04 GB/3.76 GiB)
[   19.734619] sd 2:0:0:0: [sda] Write Protect is off
[   19.734626] sd 2:0:0:0: [sda] Mode Sense: 0b 00 00 08
[   19.740610] sd 2:0:0:0: [sda] No Caching mode page present
[   19.740616] sd 2:0:0:0: [sda] Assuming drive cache: write through
[   19.756606] sd 2:0:0:0: [sda] No Caching mode page present
[   19.756611] sd 2:0:0:0: [sda] Assuming drive cache: write through
[   19.762701]  sda: sda1
[   19.785599] sd 2:0:0:0: [sda] No Caching mode page present
[   19.785605] sd 2:0:0:0: [sda] Assuming drive cache: write through
[   19.785610] sd 2:0:0:0: [sda] Attached SCSI removable disk
[   20.276370] hotplug (102): /proc/102/oom_adj is deprecated, please use /proc/102/oom_score_adj instead.
[   20.291250] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[   20.303712] Loading iSCSI transport class v2.0-870.
[   20.327240] iscsi: registered transport (tcp)
[   20.335410] Floppy drive(s): fd0 is 1.44M
[   23.352044] floppy0: no floppy controllers found
[   23.363353] BIOS EDD facility v0.16 2004-Jun-25, 3 devices found
[   23.368260] input: PC Speaker as /devices/platform/pcspkr/input/input4
[   23.377470] No iBFT detected.
[   23.429523] NET: Registered protocol family 10
[   23.531622] tg3.c:v3.116 (December 3, 2010)
[   23.531675] tg3 0000:03:01.0: PCI INT A -> GSI 25 (level, low) -> IRQ 25
[   23.537672] HP CISS Driver (v 3.6.26)
[   23.546235] cciss 0000:04:03.0: PCI INT A -> GSI 51 (level, low) -> IRQ 51
[   23.586531] cciss 0000:04:03.0: cciss0: <0x46> at PCI 0000:04:03.0 IRQ 51 using DAC
[   23.587795] tg3 0000:03:01.0: eth0: Tigon3 [partno(N/A) rev 2100] (PCIX:133MHz:64-bit) MAC address 00:0f:20:f9:29:a1
[   23.587808] tg3 0000:03:01.0: eth0: attached PHY is 5704 (10/100/1000Base-T Ethernet) (WireSpeed[1])
[   23.587816] tg3 0000:03:01.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[0]
[   23.587825] tg3 0000:03:01.0: eth0: dma_rwctrl[769f4000] dma_mask[64-bit]
[   23.587882] tg3 0000:03:01.1: enabling device (0140 -> 0142)
[   23.587930] tg3 0000:03:01.1: PCI INT B -> GSI 26 (level, low) -> IRQ 26
[   23.610633]  cciss/c0d0: p1 p2 p3 p4
[   23.615761]  cciss/c0d1: p1
[   23.642277] tg3 0000:03:01.1: eth1: Tigon3 [partno(N/A) rev 2100] (PCIX:133MHz:64-bit) MAC address 00:0f:20:f9:29:a0
[   23.642289] tg3 0000:03:01.1: eth1: attached PHY is 5704 (10/100/1000Base-T Ethernet) (WireSpeed[1])
[   23.642297] tg3 0000:03:01.1: eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[   23.642305] tg3 0000:03:01.1: eth1: dma_rwctrl[769f4000] dma_mask[64-bit]
[   24.658012] cciss 0000:04:03.0: vpd r/w failed.  This is likely a firmware bug on this device.  Contact the card vendor for a firmware update.
[   24.958017] cciss 0000:04:03.0: vpd r/w failed.  This is likely a firmware bug on this device.  Contact the card vendor for a firmware update.
[   25.112174] udev[125]: renamed network interface eth1 to em2
[   25.408186] udev[123]: renamed network interface eth0 to em1
[   31.636949] ISO 9660 Extensions: Microsoft Joliet Level 3
[   31.640835] ISO 9660 Extensions: RRIP_1991A
[   38.529113] SELinux: 2048 avtab hash slots, 220448 rules.
[   38.652358] SELinux: 2048 avtab hash slots, 220448 rules.
[   39.445680] SELinux:  9 users, 13 roles, 3606 types, 191 bools, 1 sens, 1024 cats
[   39.445687] SELinux:  81 classes, 220448 rules
[   39.457989] SELinux:  Completing initialization.
[   39.457993] SELinux:  Setting up existing superblocks.
[   39.458030] SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
[   39.458045] SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
[   39.467020] SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
[   39.467035] SELinux: initialized (dev proc, type proc), uses genfs_contexts
[   39.467062] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[   39.467109] SELinux: initialized (dev devtmpfs, type devtmpfs), uses transition SIDs
[   39.467469] SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
[   39.467479] SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
[   39.469709] SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
[   39.469731] SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts
[   39.469738] SELinux: initialized (dev devpts, type devpts), uses transition SIDs
[   39.469764] SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses transition SIDs
[   39.469790] SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
[   39.469831] SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
[   39.469860] SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
[   39.469871] SELinux: initialized (dev securityfs, type securityfs), uses genfs_contexts
[   39.469878] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[   39.470852] SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
[   39.472113] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[   39.484525] type=1403 audit(1184895703.960:2): policy loaded auid=4294967295 ses=4294967295
[   39.540200] md: raid0 personality registered for level 0
[   39.548844] md: raid1 personality registered for level 1
[   39.554113] async_tx: api initialized (async)
[   39.555876] xor: automatically using best checksumming function: generic_sse
[   39.560012]    generic_sse:  4304.000 MB/sec
[   39.560018] xor: using function: generic_sse (4304.000 MB/sec)
[   39.580058] raid6: int64x1   1242 MB/s
[   39.597038] raid6: int64x2   1207 MB/s
[   39.614020] raid6: int64x4   1746 MB/s
[   39.631019] raid6: int64x8   1371 MB/s
[   39.648036] raid6: sse2x1    2140 MB/s
[   39.665024] raid6: sse2x2    3089 MB/s
[   39.682017] raid6: sse2x4    3515 MB/s
[   39.682020] raid6: using algorithm sse2x4 (3515 MB/s)
[   39.691946] md: raid6 personality registered for level 6
[   39.691952] md: raid5 personality registered for level 5
[   39.691957] md: raid4 personality registered for level 4
[   39.705600] md: raid10 personality registered for level 10
[   39.710121] md: linear personality registered for level -1
[   39.728839] device-mapper: multipath: version 1.2.0 loaded
[   39.733000] device-mapper: multipath round-robin: version 1.0.0 loaded
[   67.600638] ADDRCONF(NETDEV_UP): em1: link is not ready
[   68.011676] ADDRCONF(NETDEV_UP): em2: link is not ready
[   73.171153] tg3 0000:03:01.0: em1: Link is up at 1000 Mbps, full duplex
[   73.171159] tg3 0000:03:01.0: em1: Flow control is on for TX and on for RX
[   73.172398] ADDRCONF(NETDEV_CHANGE): em1: link becomes ready
[   84.130030] em1: no IPv6 routers present
[   92.329549] EXT4-fs (cciss!c0d0p1): mounted filesystem with ordered data mode. Opts: (null)
[   92.329571] SELinux: initialized (dev cciss!c0d0p1, type ext4), uses xattr
[   92.469501] EXT4-fs (cciss!c0d0p2): mounted filesystem with ordered data mode. Opts: (null)
[   92.469518] SELinux: initialized (dev cciss!c0d0p2, type ext4), uses xattr
[   92.632975] EXT4-fs (cciss!c0d0p4): mounted filesystem with ordered data mode. Opts: (null)
[   92.632993] SELinux: initialized (dev cciss!c0d0p4, type ext4), uses xattr
[   92.896545] EXT4-fs (cciss!c0d1p1): mounted filesystem with ordered data mode. Opts: (null)
[   92.896568] SELinux: initialized (dev cciss!c0d1p1, type ext4), uses xattr
[   93.103298] EXT4-fs (cciss!c0d0p2): mounted filesystem with ordered data mode. Opts: (null)
[   93.103316] SELinux: initialized (dev cciss!c0d0p2, type ext4), uses xattr
[   93.250030] EXT4-fs (cciss!c0d0p1): mounted filesystem with ordered data mode. Opts: (null)
[   93.250048] SELinux: initialized (dev cciss!c0d0p1, type ext4), uses xattr
[   93.309600] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[   93.372771] EXT4-fs (cciss!c0d0p4): mounted filesystem with ordered data mode. Opts: (null)
[   93.372789] SELinux: initialized (dev cciss!c0d0p4, type ext4), uses xattr
[   93.648312] EXT4-fs (cciss!c0d1p1): mounted filesystem with ordered data mode. Opts: (null)
[   93.648335] SELinux: initialized (dev cciss!c0d1p1, type ext4), uses xattr
[  106.574953] Adding 16777212k swap on /dev/cciss/c0d0p3.  Priority:-1 extents:1 across:16777212k 
[  154.753095] SELinux: initialized (dev sda1, type vfat), uses genfs_contexts

bradycl_84043 · 11-10-2011, 11:50 PM

...And here is the dmesg from a boot into rescue mode on an FC16 disc. Note the failed attempt to load CCISS on IRQ 19.

Code:

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.1.0-7.fc16.x86_64 (mockbuild@x86-07.phx2.fedoraproject.org) (gcc version 4.6.2 20111027 (Red Hat 4.6.2-1) (GCC) ) #1 SMP Tue Nov 1 21:10:48 UTC 2011
[    0.000000] Command line: initrd=initrd.img rescue quiet BOOT_IMAGE=vmlinuz 
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
[    0.000000]  BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 00000000dfff3000 (usable)
[    0.000000]  BIOS-e820: 00000000dfff3000 - 00000000dfffb000 (ACPI data)
[    0.000000]  BIOS-e820: 00000000dfffb000 - 00000000e0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fed00000 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
[    0.000000]  BIOS-e820: 00000000ffc00000 - 0000000100000000 (reserved)
[    0.000000]  BIOS-e820: 0000000100000000 - 000000021bfff000 (usable)
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] DMI 2.3 present.
[    0.000000] DMI: HP ProLiant DL380 G4, BIOS P51 07/19/2007
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[    0.000000] No AGP bridge found
[    0.000000] last_pfn = 0x21bfff max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: write-back
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-C7FFF write-protect
[    0.000000]   C8000-E7FFF uncachable
[    0.000000]   E8000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 0E0000000 mask FE0000000 uncachable
[    0.000000]   1 disabled
[    0.000000]   2 disabled
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] last_pfn = 0xdfff3 max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [ffff8800000f4f80] f4f80
[    0.000000] initial memory mapped : 0 - 20000000
[    0.000000] Base memory trampoline at [ffff88000009a000] 9a000 size 20480
[    0.000000] init_memory_mapping: 0000000000000000-00000000dfff3000
[    0.000000]  0000000000 - 00dfe00000 page 2M
[    0.000000]  00dfe00000 - 00dfff3000 page 4k
[    0.000000] kernel direct mapping tables up to dfff3000 @ 1fffa000-20000000
[    0.000000] init_memory_mapping: 0000000100000000-000000021bfff000
[    0.000000]  0100000000 - 021be00000 page 2M
[    0.000000]  021be00000 - 021bfff000 page 4k
[    0.000000] kernel direct mapping tables up to 21bfff000 @ dffe8000-dfff3000
[    0.000000] RAMDISK: 77e97000 - 7ffff000
[    0.000000] ACPI: RSDP 00000000000f4f00 00024 (v02 HP    )
[    0.000000] ACPI: XSDT 00000000dfff3300 00044 (v01 HP     P51      00000002   \xffffffd2? 0000162E)
[    0.000000] ACPI: FACP 00000000dfff3380 000F4 (v03 HP     P51      00000002   \xffffffd2? 0000162E)
[    0.000000] ACPI Warning: Invalid length for Pm1aControlBlock: 32, using default 16 (20110623/tbfadt-610)
[    0.000000] ACPI: DSDT 00000000dfff3480 02DAB (v01 HP         DSDT 00000001 INTL 20030228)
[    0.000000] ACPI: FACS 00000000dfff3100 00040
[    0.000000] ACPI: SPCR 00000000dfff3140 00050 (v01 HP     SPCRRBSU 00000001   \xffffffd2? 0000162E)
[    0.000000] ACPI: MCFG 00000000dfff31c0 0003C (v01 HP     ProLiant 00000001      00000000)
[    0.000000] ACPI: APIC 00000000dfff3200 000C2 (v01 HP     00000083 00000002      00000000)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at 0000000000000000-000000021bfff000
[    0.000000] Initmem setup node 0 0000000000000000-000000021bfff000
[    0.000000]   NODE_DATA [000000021bfeb000 - 000000021bffefff]
[    0.000000]  [ffffea0000000000-ffffea00087fffff] PMD -> [ffff880213600000-ffff88021b5fffff] on node 0
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   DMA32    0x00001000 -> 0x00100000
[    0.000000]   Normal   0x00100000 -> 0x0021bfff
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[3] active PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x000dfff3
[    0.000000]     0: 0x00100000 -> 0x0021bfff
[    0.000000] On node 0 totalpages: 2080641
[    0.000000]   DMA zone: 64 pages used for memmap
[    0.000000]   DMA zone: 5 pages reserved
[    0.000000]   DMA zone: 3914 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 16320 pages used for memmap
[    0.000000]   DMA32 zone: 897075 pages, LIFO batch:31
[    0.000000]   Normal zone: 18176 pages used for memmap
[    0.000000]   Normal zone: 1145087 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x908
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x04] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x06] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x05] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: IOAPIC (id[0x09] address[0xfec80000] gsi_base[24])
[    0.000000] IOAPIC[1]: apic_id 9, version 32, address 0xfec80000, GSI 24-47
[    0.000000] ACPI: IOAPIC (id[0x0a] address[0xfec80400] gsi_base[48])
[    0.000000] IOAPIC[2]: apic_id 10, version 32, address 0xfec80400, GSI 48-71
[    0.000000] ACPI: IOAPIC (id[0x0b] address[0xfec84000] gsi_base[72])
[    0.000000] IOAPIC[3]: apic_id 11, version 32, address 0xfec84000, GSI 72-95
[    0.000000] ACPI: IOAPIC (id[0x0c] address[0xfec84400] gsi_base[96])
[    0.000000] IOAPIC[4]: apic_id 12, version 32, address 0xfec84400, GSI 96-119
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] SMP: Allowing 8 CPUs, 4 hotplug CPUs
[    0.000000] nr_irqs_gsi: 136
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[    0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[    0.000000] PM: Registered nosave memory: 00000000dfff3000 - 00000000dfffb000
[    0.000000] PM: Registered nosave memory: 00000000dfffb000 - 00000000e0000000
[    0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000fec00000
[    0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fed00000
[    0.000000] PM: Registered nosave memory: 00000000fed00000 - 00000000fee00000
[    0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee10000
[    0.000000] PM: Registered nosave memory: 00000000fee10000 - 00000000ffc00000
[    0.000000] PM: Registered nosave memory: 00000000ffc00000 - 0000000100000000
[    0.000000] Allocating PCI resources starting at e0000000 (gap: e0000000:1ec00000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:8 nr_node_ids:1
[    0.000000] PERCPU: Embedded 27 pages/cpu @ffff88021bc00000 s81024 r8192 d21376 u262144
[    0.000000] pcpu-alloc: s81024 r8192 d21376 u262144 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 2046076
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: initrd=initrd.img rescue quiet BOOT_IMAGE=vmlinuz 
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Checking aperture...
[    0.000000] No AGP bridge found
[    0.000000] Calgary: detecting Calgary via BIOS EBDA area
[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000000] Memory: 7977648k/8847356k available (4868k kernel code, 524792k absent, 344916k reserved, 6781k data, 940k init)
[    0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] NR_IRQS:16640 nr_irqs:2048 16
[    0.000000] Extended CMOS year: 2000
[    0.000000] spurious 8259A interrupt: IRQ7.
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] allocated 67108864 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 3400.013 MHz processor.
[    0.002008] Calibrating delay loop (skipped), value calculated using timer frequency.. 6800.02 BogoMIPS (lpj=3400013)
[    0.002015] pid_max: default: 32768 minimum: 301
[    0.002057] Security Framework initialized
[    0.002072] SELinux:  Initializing.
[    0.002090] SELinux:  Starting in permissive mode
[    0.004026] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[    0.010620] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.013542] Mount-cache hash table entries: 256
[    0.013844] Initializing cgroup subsys cpuacct
[    0.013855] Initializing cgroup subsys memory
[    0.013881] Initializing cgroup subsys devices
[    0.013885] Initializing cgroup subsys freezer
[    0.013888] Initializing cgroup subsys net_cls
[    0.013891] Initializing cgroup subsys blkio
[    0.013905] Initializing cgroup subsys perf_event
[    0.013960] CPU: Physical Processor ID: 0
[    0.013963] CPU: Processor Core ID: 0
[    0.013966] mce: CPU supports 4 MCE banks
[    0.013981] CPU0: Thermal monitoring enabled (TM1)
[    0.014014] using mwait in idle threads.
[    0.014772] ACPI: Core revision 20110623
[    0.018012] ftrace: allocating 25204 entries in 99 pages
[    0.020403] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
[    0.030416] CPU0: Intel(R) Xeon(TM) CPU 3.40GHz stepping 01
[    0.030997] Performance Events: Netburst events, Broken PMU hardware detected, using software events only.
[    0.030997] NMI watchdog disabled (cpu0): hardware events not enabled
[    0.030997] Booting Node   0, Processors  #1
[    0.030997] smpboot cpu 1: start_ip = 9a000
[    0.102016] NMI watchdog disabled (cpu1): hardware events not enabled
[    0.102189]  #2
[    0.102192] smpboot cpu 2: start_ip = 9a000
[    0.174016] NMI watchdog disabled (cpu2): hardware events not enabled
[    0.174200]  #3
[    0.174203] smpboot cpu 3: start_ip = 9a000
[    0.245986] NMI watchdog disabled (cpu3): hardware events not enabled
[    0.246017] Brought up 4 CPUs
[    0.246022] Total of 4 processors activated (27197.17 BogoMIPS).
[    0.247155] devtmpfs: initialized
[    0.251966] atomic64 test passed for x86-64 platform with CX8 and with SSE
[    0.252005] RTC time:  1:47:14, date: 07/20/07
[    0.252073] NET: Registered protocol family 16
[    0.252351] ACPI: bus type pci registered
[    0.252437] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.252442] PCI: Intel Corporation E7520 Memory Controller Hub with MMCONFIG support
[    0.252449] PCI: not using MMCONFIG
[    0.252452] PCI: Using configuration type 1 for base access
[    0.252461] PCI: HP ProLiant DL380 detected, enabling pci=bfsort.
[    0.252700] mtrr: your CPUs had inconsistent fixed MTRR settings
[    0.252703] mtrr: probably your BIOS does not setup all CPUs.
[    0.252705] mtrr: corrected configuration.
[    0.254245] bio: create slab <bio-0> at 0
[    0.254245] ACPI: Added _OSI(Module Device)
[    0.254245] ACPI: Added _OSI(Processor Device)
[    0.254245] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.254245] ACPI: Added _OSI(Processor Aggregator Device)
[    0.255510] ACPI: EC: Look up EC in DSDT
[    0.257515] ACPI: Interpreter enabled
[    0.257521] ACPI: (supports S0 S4 S5)
[    0.257544] ACPI: Using IOAPIC for interrupt routing
[    0.264334] ACPI: No dock devices found.
[    0.264339] HEST: Table not found.
[    0.264344] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[    0.264422] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-7f])
[    0.264571] pci_root PNP0A03:00: host bridge window [io  0x0000-0x0cf7] (ignored)
[    0.264575] pci_root PNP0A03:00: host bridge window [io  0x0d00-0xffff] (ignored)
[    0.264579] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[    0.264583] pci_root PNP0A03:00: host bridge window [mem 0xe0000000-0xfebfffff] (ignored)
[    0.264600] pci 0000:00:00.0: [8086:3590] type 0 class 0x000600
[    0.264677] pci 0000:00:02.0: [8086:3595] type 1 class 0x000604
[    0.264728] pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
[    0.264734] pci 0000:00:02.0: PME# disabled
[    0.264768] pci 0000:00:06.0: [8086:3599] type 1 class 0x000604
[    0.264819] pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
[    0.264824] pci 0000:00:06.0: PME# disabled
[    0.264872] pci 0000:00:1d.0: [8086:24d2] type 0 class 0x000c03
[    0.264924] pci 0000:00:1d.0: reg 20: [io  0x3000-0x301f]
[    0.264962] pci 0000:00:1d.1: [8086:24d4] type 0 class 0x000c03
[    0.265020] pci 0000:00:1d.1: reg 20: [io  0x3020-0x303f]
[    0.265062] pci 0000:00:1d.2: [8086:24d7] type 0 class 0x000c03
[    0.265116] pci 0000:00:1d.2: reg 20: [io  0x3040-0x305f]
[    0.265155] pci 0000:00:1d.3: [8086:24de] type 0 class 0x000c03
[    0.265206] pci 0000:00:1d.3: reg 20: [io  0x3060-0x307f]
[    0.265252] pci 0000:00:1e.0: [8086:244e] type 1 class 0x000604
[    0.265302] pci 0000:00:1f.0: [8086:24d0] type 0 class 0x000601
[    0.265377] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[    0.265400] pci 0000:00:1f.1: [8086:24db] type 0 class 0x000101
[    0.265417] pci 0000:00:1f.1: reg 10: [io  0x01f0-0x01f7]
[    0.265429] pci 0000:00:1f.1: reg 14: [io  0x03f4-0x03f7]
[    0.265440] pci 0000:00:1f.1: reg 18: [io  0x0170-0x0177]
[    0.265452] pci 0000:00:1f.1: reg 1c: [io  0x0374-0x0377]
[    0.265463] pci 0000:00:1f.1: reg 20: [io  0x0500-0x050f]
[    0.265475] pci 0000:00:1f.1: reg 24: [mem 0x00000000-0x000003ff]
[    0.265557] pci 0000:02:00.0: [8086:0329] type 1 class 0x000604
[    0.265576] pci 0000:02:00.0: PXH quirk detected; SHPC device MSI disabled
[    0.265627] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[    0.265632] pci 0000:02:00.0: PME# disabled
[    0.265655] pci 0000:02:00.2: [8086:032a] type 1 class 0x000604
[    0.265672] pci 0000:02:00.2: PXH quirk detected; SHPC device MSI disabled
[    0.265722] pci 0000:02:00.2: PME# supported from D0 D3hot D3cold
[    0.265726] pci 0000:02:00.2: PME# disabled
[    0.265744] pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.265750] pci 0000:00:02.0: PCI bridge to [bus 02-04]
[    0.265756] pci 0000:00:02.0:   bridge window [io  0x4000-0x4fff]
[    0.265760] pci 0000:00:02.0:   bridge window [mem 0xf7e00000-0xf7ffffff]
[    0.265815] pci 0000:03:01.0: [14e4:1648] type 0 class 0x000200
[    0.265837] pci 0000:03:01.0: reg 10: [mem 0xf7ef0000-0xf7efffff 64bit]
[    0.265898] pci 0000:03:01.0: PME# supported from D3hot D3cold
[    0.265903] pci 0000:03:01.0: PME# disabled
[    0.265930] pci 0000:03:01.1: [14e4:1648] type 0 class 0x000200
[    0.265952] pci 0000:03:01.1: reg 10: [mem 0x00000000-0x0000ffff 64bit]
[    0.266022] pci 0000:03:01.1: PME# supported from D3hot D3cold
[    0.266027] pci 0000:03:01.1: PME# disabled
[    0.266077] pci 0000:02:00.0: PCI bridge to [bus 03-03]
[    0.266084] pci 0000:02:00.0:   bridge window [mem 0xf7e00000-0xf7efffff]
[    0.266142] pci 0000:04:03.0: [0e11:0046] type 0 class 0x000104
[    0.266166] pci 0000:04:03.0: reg 10: [mem 0xf7ff0000-0xf7ff1fff 64bit]
[    0.266176] pci 0000:04:03.0: reg 18: [io  0x4000-0x40ff]
[    0.266190] pci 0000:04:03.0: reg 1c: [mem 0xf7f80000-0xf7fbffff 64bit]
[    0.266208] pci 0000:04:03.0: reg 30: [mem 0x00000000-0x0003ffff pref]
[    0.266232] pci 0000:04:03.0: supports D1
[    0.266273] pci 0000:02:00.2: PCI bridge to [bus 04-04]
[    0.266277] pci 0000:02:00.2:   bridge window [io  0x4000-0x4fff]
[    0.266282] pci 0000:02:00.2:   bridge window [mem 0xf7f00000-0xf7ffffff]
[    0.266341] pci 0000:05:00.0: [8086:0329] type 1 class 0x000604
[    0.266359] pci 0000:05:00.0: PXH quirk detected; SHPC device MSI disabled
[    0.266409] pci 0000:05:00.0: PME# supported from D0 D3hot D3cold
[    0.266414] pci 0000:05:00.0: PME# disabled
[    0.266437] pci 0000:05:00.2: [8086:032a] type 1 class 0x000604
[    0.266455] pci 0000:05:00.2: PXH quirk detected; SHPC device MSI disabled
[    0.266505] pci 0000:05:00.2: PME# supported from D0 D3hot D3cold
[    0.266509] pci 0000:05:00.2: PME# disabled
[    0.266526] pci 0000:05:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.266531] pci 0000:00:06.0: PCI bridge to [bus 05-0c]
[    0.266537] pci 0000:00:06.0:   bridge window [mem 0xf8000000-0xfdffffff]
[    0.266589] pci 0000:06:01.0: [14f1:8800] type 0 class 0x000400
[    0.266610] pci 0000:06:01.0: reg 10: [mem 0xfd000000-0xfdffffff]
[    0.266705] pci 0000:06:01.1: [14f1:8801] type 0 class 0x000480
[    0.266725] pci 0000:06:01.1: reg 10: [mem 0xfc000000-0xfcffffff]
[    0.266810] pci 0000:06:01.2: [14f1:8802] type 0 class 0x000480
[    0.266829] pci 0000:06:01.2: reg 10: [mem 0xfb000000-0xfbffffff]
[    0.266923] pci 0000:06:02.0: [14f1:8800] type 0 class 0x000400
[    0.266943] pci 0000:06:02.0: reg 10: [mem 0xfa000000-0xfaffffff]
[    0.267043] pci 0000:06:02.1: [14f1:8801] type 0 class 0x000480
[    0.267062] pci 0000:06:02.1: reg 10: [mem 0xf9000000-0xf9ffffff]
[    0.267149] pci 0000:06:02.2: [14f1:8802] type 0 class 0x000480
[    0.267168] pci 0000:06:02.2: reg 10: [mem 0xf8000000-0xf8ffffff]
[    0.267286] pci 0000:05:00.0: PCI bridge to [bus 06-09]
[    0.267292] pci 0000:05:00.0:   bridge window [mem 0xf8000000-0xfdffffff]
[    0.267365] pci 0000:05:00.2: PCI bridge to [bus 0a-0c]
[    0.267412] pci 0000:01:03.0: [1002:4752] type 0 class 0x000300
[    0.267432] pci 0000:01:03.0: reg 10: [mem 0xf6000000-0xf6ffffff]
[    0.267443] pci 0000:01:03.0: reg 14: [io  0x2000-0x20ff]
[    0.267455] pci 0000:01:03.0: reg 18: [mem 0xf5ff0000-0xf5ff0fff]
[    0.267494] pci 0000:01:03.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[    0.267515] pci 0000:01:03.0: supports D1 D2
[    0.267537] pci 0000:01:04.0: [0e11:b203] type 0 class 0x000880
[    0.267556] pci 0000:01:04.0: reg 10: [io  0x1800-0x18ff]
[    0.267567] pci 0000:01:04.0: reg 14: [mem 0xf5fe0000-0xf5fe01ff]
[    0.267647] pci 0000:01:04.2: [0e11:b204] type 0 class 0x000880
[    0.267668] pci 0000:01:04.2: reg 10: [io  0x2400-0x24ff]
[    0.267680] pci 0000:01:04.2: reg 14: [mem 0xf5fd0000-0xf5fd07ff]
[    0.267692] pci 0000:01:04.2: reg 18: [mem 0xf5fc0000-0xf5fc1fff]
[    0.267703] pci 0000:01:04.2: reg 1c: [mem 0xf5f00000-0xf5f7ffff]
[    0.267733] pci 0000:01:04.2: reg 30: [mem 0x00000000-0x0000ffff pref]
[    0.267757] pci 0000:01:04.2: PME# supported from D0 D3hot D3cold
[    0.267762] pci 0000:01:04.2: PME# disabled
[    0.267813] pci 0000:00:1e.0: PCI bridge to [bus 01-01] (subtractive decode)
[    0.267819] pci 0000:00:1e.0:   bridge window [io  0x1000-0x2fff]
[    0.267824] pci 0000:00:1e.0:   bridge window [mem 0xf5f00000-0xf6ffffff]
[    0.267831] pci 0000:00:1e.0:   bridge window [io  0x0000-0xffff] (subtractive decode)
[    0.267836] pci 0000:00:1e.0:   bridge window [mem 0x00000000-0xfffffffff] (subtractive decode)
[    0.267857] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.267989] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.IP2P._PRT]
[    0.268052] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PTA0._PRT]
[    0.268109] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PTA0.PCXA._PRT]
[    0.268165] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PTA0.PCXB._PRT]
[    0.268207] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PTC0._PRT]
[    0.268262] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PTC0.PCXC._PRT]
[    0.268405] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PTC0.PCXD._PRT]
[    0.268493]  pci0000:00: Unable to request _OSC control (_OSC support mask: 0x1e)
[    0.281165] ACPI: PCI Interrupt Link [LNKA] (IRQs *5 7 10 11)
[    0.281232] ACPI: PCI Interrupt Link [LNKB] (IRQs *5 7 10 11)
[    0.281296] ACPI: PCI Interrupt Link [LNKC] (IRQs *5 7 10 11)
[    0.281359] ACPI: PCI Interrupt Link [LNKD] (IRQs *5 7 10 11)
[    0.281423] ACPI: PCI Interrupt Link [LNKE] (IRQs 5 7 10 11) *0, disabled.
[    0.281488] ACPI: PCI Interrupt Link [LNKF] (IRQs *5 7 10 11)
[    0.281552] ACPI: PCI Interrupt Link [LNKG] (IRQs *5 7 10 11)
[    0.281615] ACPI: PCI Interrupt Link [LNKH] (IRQs *5 7 10 11)
[    0.281732] vgaarb: device added: PCI:0000:01:03.0,decodes=io+mem,owns=none,locks=none
[    0.281732] vgaarb: loaded
[    0.281732] vgaarb: bridge control possible 0000:01:03.0
[    0.281732] SCSI subsystem initialized
[    0.282012] libata version 3.00 loaded.
[    0.282094] usbcore: registered new interface driver usbfs
[    0.282122] usbcore: registered new interface driver hub
[    0.282129] usbcore: registered new device driver usb
[    0.282129] PCI: Using ACPI for IRQ routing
[    0.282129] PCI: pci_cache_line_size set to 64 bytes
[    0.282131] reserve RAM buffer: 000000000009f400 - 000000000009ffff 
[    0.282135] reserve RAM buffer: 00000000dfff3000 - 00000000dfffffff 
[    0.282138] reserve RAM buffer: 000000021bfff000 - 000000021bffffff 
[    0.282288] NetLabel: Initializing
[    0.282291] NetLabel:  domain hash size = 128
[    0.282293] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.282311] NetLabel:  unlabeled traffic allowed by default
[    0.282402] hpet clockevent registered
[    0.282407] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.282413] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.282420] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.287002] Switching to clocksource hpet
[    0.287888] Switched to NOHz mode on CPU #0
[    0.287855] Switched to NOHz mode on CPU #3
[    0.287890] Switched to NOHz mode on CPU #1
[    0.287971] Switched to NOHz mode on CPU #2
[    0.301311] pnp: PnP ACPI init
[    0.301346] ACPI: bus type pnp registered
[    0.301465] pnp 00:00: [bus 00-7f]
[    0.301469] pnp 00:00: [io  0x0000-0x0cf7 window]
[    0.301473] pnp 00:00: [io  0x0d00-0xffff window]
[    0.301476] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[    0.301479] pnp 00:00: [mem 0xe0000000-0xfebfffff window]
[    0.301545] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
[    0.303144] pnp 00:01: [io  0x0070-0x0077]
[    0.303148] pnp 00:01: [io  0x0408-0x040f]
[    0.303150] pnp 00:01: [io  0x04d0-0x04d1]
[    0.303153] pnp 00:01: [io  0x0020-0x003f]
[    0.303156] pnp 00:01: [io  0x00a0-0x00bf]
[    0.303158] pnp 00:01: [io  0x0090-0x009f]
[    0.303161] pnp 00:01: [io  0x0050-0x0053]
[    0.303164] pnp 00:01: [io  0x0700-0x071f]
[    0.303166] pnp 00:01: [io  0x0800-0x083f]
[    0.303169] pnp 00:01: [io  0x0900-0x097f]
[    0.303171] pnp 00:01: [io  0x0010-0x001f]
[    0.303174] pnp 00:01: [io  0x0c80-0x0c83]
[    0.303177] pnp 00:01: [io  0x0cd4-0x0cd7]
[    0.303179] pnp 00:01: [io  0x0f50-0x0f58]
[    0.303182] pnp 00:01: [io  0x02f8-0x02ff]
[    0.303185] pnp 00:01: [mem 0xe0000000-0xefffffff]
[    0.303286] system 00:01: [io  0x0408-0x040f] has been reserved
[    0.303291] system 00:01: [io  0x04d0-0x04d1] has been reserved
[    0.303294] system 00:01: [io  0x0700-0x071f] has been reserved
[    0.303298] system 00:01: [io  0x0800-0x083f] has been reserved
[    0.303301] system 00:01: [io  0x0900-0x097f] has been reserved
[    0.303305] system 00:01: [io  0x0c80-0x0c83] has been reserved
[    0.303308] system 00:01: [io  0x0cd4-0x0cd7] has been reserved
[    0.303312] system 00:01: [io  0x0f50-0x0f58] has been reserved
[    0.303315] system 00:01: [io  0x02f8-0x02ff] has been reserved
[    0.303320] system 00:01: [mem 0xe0000000-0xefffffff] has been reserved
[    0.303325] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.303345] pnp 00:02: [dma 7]
[    0.303348] pnp 00:02: [io  0x0000-0x000f]
[    0.303351] pnp 00:02: [io  0x0080-0x008f]
[    0.303353] pnp 00:02: [io  0x00c0-0x00df]
[    0.303399] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.303414] pnp 00:03: [io  0x0061]
[    0.303454] pnp 00:03: Plug and Play ACPI device, IDs PNP0800 (active)
[    0.303470] pnp 00:04: [io  0x0060]
[    0.303474] pnp 00:04: [io  0x0064]
[    0.303490] pnp 00:04: [irq 1]
[    0.303535] pnp 00:04: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.303555] pnp 00:05: [irq 12]
[    0.303597] pnp 00:05: Plug and Play ACPI device, IDs PNP0f13 PNP0f0e (active)
[    0.303614] pnp 00:06: [io  0x002e-0x002f]
[    0.303617] pnp 00:06: [io  0x004e-0x004f]
[    0.303620] pnp 00:06: [io  0x0220-0x025f]
[    0.303623] pnp 00:06: [io  0x0280-0x029f]
[    0.303663] pnp 00:06: Plug and Play ACPI device, IDs PNP0a06 (active)
[    0.303791] pnp 00:07: Plug and Play ACPI device, IDs PNP0501 PNP0500 (disabled)
[    0.303889] pnp 00:08: Plug and Play ACPI device, IDs PNP0700 (disabled)

Continued below...

bradycl_84043 · 11-10-2011, 11:52 PM

Part 2 of dmesg for boot into rescue mode on FC16 with failed CCISS load:

Code:

[    0.304139] pnp: PnP ACPI: found 9 devices
[    0.304142] ACPI: ACPI bus type pnp unregistered
[    0.313798] PCI: max bus depth: 2 pci_try_num: 3
[    0.313861] pci 0000:00:02.0: BAR 15: assigned [mem 0xf0000000-0xf00fffff pref]
[    0.313866] pci 0000:00:1e.0: BAR 15: assigned [mem 0xf0100000-0xf01fffff pref]
[    0.313871] pci 0000:00:1f.1: BAR 5: assigned [mem 0xf0200000-0xf02003ff]
[    0.313878] pci 0000:00:1f.1: BAR 5: set to [mem 0xf0200000-0xf02003ff] (PCI address [0xf0200000-0xf02003ff])
[    0.313883] pci 0000:02:00.2: BAR 15: assigned [mem 0xf0000000-0xf00fffff pref]
[    0.313888] pci 0000:03:01.1: BAR 0: assigned [mem 0xf7e00000-0xf7e0ffff 64bit]
[    0.313896] pci 0000:03:01.1: BAR 0: set to [mem 0xf7e00000-0xf7e0ffff 64bit] (PCI address [0xf7e00000-0xf7e0ffff])
[    0.313900] pci 0000:02:00.0: PCI bridge to [bus 03-03]
[    0.313906] pci 0000:02:00.0:   bridge window [mem 0xf7e00000-0xf7efffff]
[    0.313915] pci 0000:04:03.0: BAR 6: assigned [mem 0xf0000000-0xf003ffff pref]
[    0.313919] pci 0000:02:00.2: PCI bridge to [bus 04-04]
[    0.313923] pci 0000:02:00.2:   bridge window [io  0x4000-0x4fff]
[    0.313928] pci 0000:02:00.2:   bridge window [mem 0xf7f00000-0xf7ffffff]
[    0.313933] pci 0000:02:00.2:   bridge window [mem 0xf0000000-0xf00fffff pref]
[    0.313939] pci 0000:00:02.0: PCI bridge to [bus 02-04]
[    0.313943] pci 0000:00:02.0:   bridge window [io  0x4000-0x4fff]
[    0.313949] pci 0000:00:02.0:   bridge window [mem 0xf7e00000-0xf7ffffff]
[    0.313953] pci 0000:00:02.0:   bridge window [mem 0xf0000000-0xf00fffff pref]
[    0.313961] pci 0000:05:00.0: PCI bridge to [bus 06-09]
[    0.313966] pci 0000:05:00.0:   bridge window [mem 0xf8000000-0xfdffffff]
[    0.313974] pci 0000:05:00.2: PCI bridge to [bus 0a-0c]
[    0.313985] pci 0000:00:06.0: PCI bridge to [bus 05-0c]
[    0.313990] pci 0000:00:06.0:   bridge window [mem 0xf8000000-0xfdffffff]
[    0.314000] pci 0000:01:03.0: BAR 6: assigned [mem 0xf0100000-0xf011ffff pref]
[    0.314014] pci 0000:01:04.2: BAR 6: assigned [mem 0xf0120000-0xf012ffff pref]
[    0.314018] pci 0000:00:1e.0: PCI bridge to [bus 01-01]
[    0.314022] pci 0000:00:1e.0:   bridge window [io  0x1000-0x2fff]
[    0.314029] pci 0000:00:1e.0:   bridge window [mem 0xf5f00000-0xf6ffffff]
[    0.314034] pci 0000:00:1e.0:   bridge window [mem 0xf0100000-0xf01fffff pref]
[    0.314063] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.314069] pci 0000:00:02.0: setting latency timer to 64
[    0.314085] pci 0000:02:00.0: setting latency timer to 64
[    0.314093] pci 0000:02:00.2: setting latency timer to 64
[    0.314101] pci 0000:00:06.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.314106] pci 0000:00:06.0: setting latency timer to 64
[    0.314119] pci 0000:05:00.0: setting latency timer to 64
[    0.314127] pci 0000:05:00.2: setting latency timer to 64
[    0.314135] pci 0000:00:1e.0: setting latency timer to 64
[    0.314140] pci_bus 0000:00: resource 0 [io  0x0000-0xffff]
[    0.314143] pci_bus 0000:00: resource 1 [mem 0x00000000-0xfffffffff]
[    0.314147] pci_bus 0000:02: resource 0 [io  0x4000-0x4fff]
[    0.314150] pci_bus 0000:02: resource 1 [mem 0xf7e00000-0xf7ffffff]
[    0.314153] pci_bus 0000:02: resource 2 [mem 0xf0000000-0xf00fffff pref]
[    0.314156] pci_bus 0000:03: resource 1 [mem 0xf7e00000-0xf7efffff]
[    0.314159] pci_bus 0000:04: resource 0 [io  0x4000-0x4fff]
[    0.314162] pci_bus 0000:04: resource 1 [mem 0xf7f00000-0xf7ffffff]
[    0.314165] pci_bus 0000:04: resource 2 [mem 0xf0000000-0xf00fffff pref]
[    0.314168] pci_bus 0000:05: resource 1 [mem 0xf8000000-0xfdffffff]
[    0.314171] pci_bus 0000:06: resource 1 [mem 0xf8000000-0xfdffffff]
[    0.314175] pci_bus 0000:01: resource 0 [io  0x1000-0x2fff]
[    0.314178] pci_bus 0000:01: resource 1 [mem 0xf5f00000-0xf6ffffff]
[    0.314181] pci_bus 0000:01: resource 2 [mem 0xf0100000-0xf01fffff pref]
[    0.314184] pci_bus 0000:01: resource 4 [io  0x0000-0xffff]
[    0.314187] pci_bus 0000:01: resource 5 [mem 0x00000000-0xfffffffff]
[    0.314231] NET: Registered protocol family 2
[    0.314731] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.317945] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[    0.323735] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.324477] TCP: Hash tables configured (established 524288 bind 65536)
[    0.324483] TCP reno registered
[    0.324533] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[    0.324658] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[    0.324934] NET: Registered protocol family 1
[    0.325091] pci 0000:02:00.0: rerouting interrupts for [8086:0329]
[    0.325097] pci 0000:02:00.2: rerouting interrupts for [8086:032a]
[    0.325110] pci 0000:05:00.0: rerouting interrupts for [8086:0329]
[    0.325115] pci 0000:05:00.2: rerouting interrupts for [8086:032a]
[    0.325134] PCI: CLS 64 bytes, default 64
[    0.325223] Unpacking initramfs...
[    1.189046] Freeing initrd memory: 132512k freed
[    1.279616] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    1.279623] Placing 64MB software IO TLB between ffff8800dbfe8000 - ffff8800dffe8000
[    1.279627] software IO TLB at phys 0xdbfe8000 - 0xdffe8000
[    1.279751] platform rtc_cmos: registered platform RTC device (no PNP device found)
[    1.281201] Intel AES-NI instructions are not detected.
[    1.281463] audit: initializing netlink socket (disabled)
[    1.281485] type=2000 audit(1184896035.280:1): initialized
[    1.338917] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    1.408269] VFS: Disk quotas dquot_6.5.2
[    1.408357] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.409120] msgmni has been set to 15840
[    1.409226] SELinux:  Registering netfilter hooks
[    1.409938] alg: No test for stdrng (krng)
[    1.409957] NET: Registered protocol family 38
[    1.410070] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    1.410137] io scheduler noop registered
[    1.410141] io scheduler deadline registered
[    1.410208] io scheduler cfq registered (default)
[    1.410528] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    1.410566] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    1.410569] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    1.410895] acpiphp: Slot [0] registered
[    1.411842] acpiphp: Slot [4294967295] registered
[    1.412965] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[    1.412972] ACPI: Power Button [PWRF]
[    1.414671] ACPI: acpi_idle registered with cpuidle
[    1.417656] thermal LNXTHERM:00: registered as thermal_zone0
[    1.417660] ACPI: Thermal Zone [THM0] (8 C)
[    1.417706] ERST: Table is not found!
[    1.417710] GHES: HEST is not enabled!
[    1.417888] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.448523] serial 00:07: [irq 4]
[    1.448531] serial 00:07: [io  0x03f8-0x03ff]
[    1.448872] serial 00:07: activated
[    1.469435] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.479567] Non-volatile memory driver v1.3
[    1.479571] Linux agpgart interface v0.103
[    1.481107] loop: module loaded
[    1.481276] ata_piix 0000:00:1f.1: version 2.13
[    1.481288] ata_piix 0000:00:1f.1: enabling device (0005 -> 0007)
[    1.481294] ata_piix 0000:00:1f.1: can't derive routing for PCI INT A
[    1.481342] ata_piix 0000:00:1f.1: setting latency timer to 64
[    1.481805] scsi0 : ata_piix
[    1.481944] scsi1 : ata_piix
[    1.482002] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x500 irq 14
[    1.482021] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x508 irq 15
[    1.482147] Fixed MDIO Bus: probed
[    1.482322] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.482357] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.482380] uhci_hcd: USB Universal Host Controller Interface driver
[    1.482417] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.482429] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    1.482434] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    1.482566] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[    1.482617] uhci_hcd 0000:00:1d.0: irq 16, io base 0x00003000
[    1.482684] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[    1.482689] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.482693] usb usb1: Product: UHCI Host Controller
[    1.482695] usb usb1: Manufacturer: Linux 3.1.0-7.fc16.x86_64 uhci_hcd
[    1.482698] usb usb1: SerialNumber: 0000:00:1d.0
[    1.482892] hub 1-0:1.0: USB hub found
[    1.482904] hub 1-0:1.0: 2 ports detected
[    1.483020] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    1.483043] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    1.483048] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    1.483148] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[    1.483189] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00003020
[    1.483245] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    1.483249] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.483252] usb usb2: Product: UHCI Host Controller
[    1.483254] usb usb2: Manufacturer: Linux 3.1.0-7.fc16.x86_64 uhci_hcd
[    1.483257] usb usb2: SerialNumber: 0000:00:1d.1
[    1.483431] hub 2-0:1.0: USB hub found
[    1.483438] hub 2-0:1.0: 2 ports detected
[    1.483567] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    1.483576] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    1.483580] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    1.483665] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[    1.483705] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00003040
[    1.483760] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    1.483764] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.483767] usb usb3: Product: UHCI Host Controller
[    1.483769] usb usb3: Manufacturer: Linux 3.1.0-7.fc16.x86_64 uhci_hcd
[    1.483772] usb usb3: SerialNumber: 0000:00:1d.2
[    1.483935] hub 3-0:1.0: USB hub found
[    1.483947] hub 3-0:1.0: 2 ports detected
[    1.484050] uhci_hcd 0000:00:1d.3: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.484058] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[    1.484062] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    1.484150] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[    1.484179] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00003060
[    1.484235] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    1.484239] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.484242] usb usb4: Product: UHCI Host Controller
[    1.484245] usb usb4: Manufacturer: Linux 3.1.0-7.fc16.x86_64 uhci_hcd
[    1.484247] usb usb4: SerialNumber: 0000:00:1d.3
[    1.484411] hub 4-0:1.0: USB hub found
[    1.484422] hub 4-0:1.0: 2 ports detected
[    1.484587] usbcore: registered new interface driver usbserial
[    1.484605] USB Serial support registered for generic
[    1.484623] usbcore: registered new interface driver usbserial_generic
[    1.484626] usbserial: USB Serial Driver core
[    1.484684] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
[    1.486293] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.486308] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.486544] mousedev: PS/2 mouse device common for all mice
[    1.486871] rtc_cmos rtc_cmos: RTC can wake from S4
[    1.487069] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
[    1.487098] rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
[    1.487305] device-mapper: uevent: version 1.0.3
[    1.487471] device-mapper: ioctl: 4.21.0-ioctl (2011-07-06) initialised: dm-devel@redhat.com
[    1.487630] cpuidle: using governor ladder
[    1.487634] cpuidle: using governor menu
[    1.488236] EFI Variables Facility v0.08 2004-May-17
[    1.488511] usbcore: registered new interface driver usbhid
[    1.488515] usbhid: USB HID core driver
[    1.488618] ip_tables: (C) 2000-2006 Netfilter Core Team
[    1.488643] TCP cubic registered
[    1.488646] Initializing XFRM netlink socket
[    1.488903] NET: Registered protocol family 10
[    1.489224] Mobile IPv6
[    1.489229] NET: Registered protocol family 17
[    1.489258] Registering the dns_resolver key type
[    1.489546] PM: Hibernation image not present or could not be loaded.
[    1.489569] registered taskstats version 1
[    1.523790] IMA: No TPM chip found, activating TPM-bypass!
[    1.524373]   Magic number: 15:845:761
[    1.524489] rtc_cmos rtc_cmos: setting system clock to 2007-07-20 01:47:15 UTC (1184896035)
[    1.524567] ondemand governor failed, too long transition latency of HW, fallback to performance governor
[    1.524616] ondemand governor failed, too long transition latency of HW, fallback to performance governor
[    1.524632] p4-clockmod: P4/Xeon(TM) CPU On-Demand Clock Modulation available
[    1.524692] Initializing network drop monitor service
[    1.528192] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[    1.636297] ata1.00: ATAPI: DVD-ROM DW-224E-R, K.AA, max UDMA/33
[    1.642182] ata1.00: configured for UDMA/33
[    1.644484] scsi 0:0:0:0: CD-ROM            TEAC     DVD-ROM DW-224ER K.AA PQ: 0 ANSI: 5
[    1.646203] sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray
[    1.646210] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.646429] sr 0:0:0:0: Attached scsi CD-ROM sr0
[    1.646604] sr 0:0:0:0: Attached scsi generic sg0 type 5
[    1.650103] Freeing unused kernel memory: 940k freed
[    1.650634] Write protecting the kernel read-only data: 10240k
[    1.659337] Freeing unused kernel memory: 1260k freed
[    1.670814] Freeing unused kernel memory: 1584k freed
[    1.747109] dracut: dracut-013-18.fc16
[    1.758213] dracut: root was live:/squashfs.img, liveroot is now live:/squashfs.img
[    1.775960] udevd[84]: starting version 173
[    1.784058] usb 1-1: new full speed USB device number 2 using uhci_hcd
[    1.817426] input: ImPS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio1/input/input2
[    1.927649] usb 1-1: New USB device found, idVendor=049f, idProduct=0048
[    1.927656] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    1.927661] usb 1-1: Product: Virtual Management Device
[    1.927665] usb 1-1: Manufacturer: HP
[    1.934944] input: HP Virtual Management Device as /devices/pci0000:00/0000:00:1d.0/usb1/1-1/1-1:1.0/input/input3
[    1.935243] generic-usb 0003:049F:0048.0001: input,hidraw0: USB HID v1.01 Mouse [HP Virtual Management Device] on usb-0000:00:1d.0-1/input0
[    2.037034] usb 3-1: new full speed USB device number 2 using uhci_hcd
[    2.188657] usb 3-1: New USB device found, idVendor=cd12, idProduct=ef18
[    2.188664] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.188669] usb 3-1: Product: Flash Drive
[    2.188672] usb 3-1: Manufacturer: USB
[    2.188675] usb 3-1: SerialNumber: D0D770CF02556290
[    2.232182] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.280062] Refined TSC clocksource calibration: 3400.120 MHz.
[    2.280076] Switching to clocksource tsc
[    2.337961] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null)
[    2.347568] dracut: Mounted root filesystem /dev/mapper/live-rw
[    2.439040] dracut: Switching root
[    2.952304] SELinux: 2048 avtab hash slots, 96028 rules.
[    3.002884] SELinux: 2048 avtab hash slots, 96028 rules.
[    3.022711] SELinux:  9 users, 13 roles, 3892 types, 204 bools, 1 sens, 1024 cats
[    3.022719] SELinux:  82 classes, 96028 rules
[    3.037406] SELinux:  Completing initialization.
[    3.037412] SELinux:  Setting up existing superblocks.
[    3.037433] SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
[    3.037444] SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
[    3.037454] SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
[    3.037466] SELinux: initialized (dev proc, type proc), uses genfs_contexts
[    3.037480] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[    3.037506] SELinux: initialized (dev devtmpfs, type devtmpfs), uses transition SIDs
[    3.038451] SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
[    3.038461] SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
[    3.040827] SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
[    3.040844] SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts
[    3.040851] SELinux: initialized (dev devpts, type devpts), uses transition SIDs
[    3.040881] SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses transition SIDs
[    3.040896] SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
[    3.040913] SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
[    3.040950] SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
[    3.040963] SELinux: initialized (dev securityfs, type securityfs), uses genfs_contexts
[    3.040973] SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
[    3.041735] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[    3.041755] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[    3.041805] SELinux: initialized (dev loop0, type squashfs), not configured for labeling
[    3.041815] SELinux: initialized (dev dm-0, type ext4), uses xattr
[    3.046341] type=1403 audit(1184896037.020:2): policy loaded auid=4294967295 ses=4294967295
[    3.055615] systemd[1]: Successfully loaded SELinux policy in 232ms 903us.
[    3.104570] systemd[1]: Successfully loaded SELinux database in 47ms 758us, size on heap is 475K.
[    3.112953] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[    3.114045] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
[    3.231906] systemd[1]: Relabelled /dev and /run in 117ms 640us.
[    3.238509] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
[    3.254079] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
[    3.270112] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
[    3.276107] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
[    3.292071] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
[    3.301104] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
[    3.313113] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
[    3.322093] SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
[    3.322282] systemd[1]: systemd 36 running in system mode. (+PAM +LIBWRAP +AUDIT +SELINUX +SYSVINIT +LIBCRYPTSETUP; fedora)
[    3.324315] systemd[1]: No hostname configured.
[    3.324551] systemd[1]: Initializing machine ID from random generator.
[    3.442458] systemd[1]: Failed to fully start up daemon: No such file or directory
[    3.442576] systemd[1]: Cannot add dependency job for unit fedora-readonly.service, ignoring: Unit fedora-readonly.service failed to load: No such file or directory. See system logs and 'systemctl status fedora-readonly.service' for details.
[    3.442604] systemd[1]: Cannot add dependency job for unit fedora-wait-storage.service, ignoring: Unit fedora-wait-storage.service failed to load: No such file or directory. See system logs and 'systemctl status fedora-wait-storage.service' for details.
[    3.442631] systemd[1]: Cannot add dependency job for unit systemd-remount-api-vfs.service, ignoring: Unit systemd-remount-api-vfs.service failed to load: No such file or directory. See system logs and 'systemctl status systemd-remount-api-vfs.service' for details.
[    3.442651] systemd[1]: Cannot add dependency job for unit fedora-storage-init.service, ignoring: Unit fedora-storage-init.service failed to load: No such file or directory. See system logs and 'systemctl status fedora-storage-init.service' for details.
[    3.442684] systemd[1]: Cannot add dependency job for unit lvm2-monitor.service, ignoring: Unit dm-event.socket failed to load: No such file or directory. See system logs and 'systemctl status dm-event.socket' for details.
[    3.442734] systemd[1]: Cannot add dependency job for unit avahi-daemon.socket, ignoring: Unit avahi-daemon.socket failed to load: No such file or directory. See system logs and 'systemctl status avahi-daemon.socket' for details.
[    3.442752] systemd[1]: Cannot add dependency job for unit rpcbind.socket, ignoring: Unit rpcbind.socket failed to load: No such file or directory. See system logs and 'systemctl status rpcbind.socket' for details.
[    3.442770] systemd[1]: Cannot add dependency job for unit dm-event.socket, ignoring: Unit dm-event.socket failed to load: No such file or directory. See system logs and 'systemctl status dm-event.socket' for details.
[    3.442806] systemd[1]: Cannot add dependency job for unit ip6tables.service, ignoring: Unit ip6tables.service failed to load: No such file or directory. See system logs and 'systemctl status ip6tables.service' for details.
[    3.442825] systemd[1]: Cannot add dependency job for unit iptables.service, ignoring: Unit iptables.service failed to load: No such file or directory. See system logs and 'systemctl status iptables.service' for details.
[    3.488616] SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
[    3.734468] SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses transition SIDs
[    3.761283] udevd[262]: starting version 173
[    3.843565] systemd[1]: fedora-storage-init-late.service: main process exited, code=exited, status=203
[    3.860143] systemd[1]: Unit fedora-storage-init-late.service entered failed state.
[    3.998578] systemd-fsck[313]: Root directory is writable, skipping check.
[    4.050150] systemd-vconsole-setup[325]: /bin/loadkeys failed with error code 1.
[    4.050171] systemd-vconsole-setup[325]: /bin/setfont failed with error code 1.
[    4.278175] usbcore: registered new interface driver uas
[    4.299004] mount[411]: warning: can't open /etc/fstab: No such file or directory
[    4.316138] Initializing USB Mass Storage driver...
[    4.318808] scsi2 : usb-storage 3-1:1.0
[    4.325152] usbcore: registered new interface driver usb-storage
[    4.325161] USB Mass Storage support registered.
[    4.417288] tg3.c:v3.119 (May 18, 2011)
[    4.417306] tg3 0000:03:01.0: PCI IRQ 25 -> rerouted to legacy IRQ 17
[    4.417338] tg3 0000:03:01.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    4.419367] HP CISS Driver (v 3.6.26)
[    4.420592] cciss 0000:04:03.0: PCI IRQ 51 -> rerouted to legacy IRQ 19
[    4.420605] cciss 0000:04:03.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[    4.431436] EXT4-fs (dm-0): re-mounted. Opts: user_xattr,acl,barrier=1,data=ordered
[    4.454164] IRQ handler type mismatch for IRQ 19
[    4.454223] current handler: uhci_hcd:usb2
[    4.454275] Pid: 427, comm: modprobe Not tainted 3.1.0-7.fc16.x86_64 #1
[    4.454280] Call Trace:
[    4.454298]  [<ffffffff810b1dda>] __setup_irq+0x39e/0x432
[    4.454311]  [<ffffffff81119644>] ? kmem_cache_alloc_trace+0xb3/0xc5
[    4.454331]  [<ffffffffa004c899>] ? process_indexed_cmd+0xa6/0xa6 [cciss]
[    4.454340]  [<ffffffff810b1f58>] request_threaded_irq+0xea/0x116
[    4.454354]  [<ffffffffa004ebc0>] cciss_request_irq+0x66/0x98 [cciss]
[    4.454368]  [<ffffffffa004ddd1>] cciss_init_one+0x1119/0x1a25 [cciss]
[    4.454377]  [<ffffffff8111a62f>] ? kmem_cache_alloc+0x31/0xf8
[    4.454385]  [<ffffffff811829d0>] ? sysfs_find_dirent+0x3c/0x55
[    4.454395]  [<ffffffff81085db7>] ? arch_local_irq_save+0x15/0x1b
[    4.454406]  [<ffffffff8123f9b7>] local_pci_probe+0x44/0x75
[    4.454415]  [<ffffffff8124051a>] pci_device_probe+0xd0/0xff
[    4.454427]  [<ffffffff812de4b7>] driver_probe_device+0x131/0x213
[    4.454435]  [<ffffffff812de5f3>] __driver_attach+0x5a/0x7e
[    4.454444]  [<ffffffff812de599>] ? driver_probe_device+0x213/0x213
[    4.454452]  [<ffffffff812dd53f>] bus_for_each_dev+0x53/0x89
[    4.454460]  [<ffffffff812de096>] driver_attach+0x1e/0x20
[    4.454467]  [<ffffffff812ddcba>] bus_add_driver+0xd1/0x224
[    4.454476]  [<ffffffffa0065000>] ? 0xffffffffa0064fff
[    4.454484]  [<ffffffff812dea97>] driver_register+0x98/0x105
[    4.454492]  [<ffffffffa0065000>] ? 0xffffffffa0064fff
[    4.454499]  [<ffffffff81240ddd>] __pci_register_driver+0x56/0xc1
[    4.454506]  [<ffffffffa0065000>] ? 0xffffffffa0064fff
[    4.454518]  [<ffffffffa006507d>] cciss_init+0x7d/0xa1 [cciss]
[    4.454529]  [<ffffffff81002099>] do_one_initcall+0x7f/0x136
[    4.454537]  [<ffffffff8108a5dd>] sys_init_module+0x88/0x1d0
[    4.454548]  [<ffffffff814bc482>] system_call_fastpath+0x16/0x1b
[    4.454556] cciss 0000:04:03.0: Unable to get irq 19 for cciss0
[    4.454665] cciss: probe of 0000:04:03.0 failed with error -1
[    4.484958] tg3 0000:03:01.0: eth0: Tigon3 [partno(N/A) rev 2100] (PCIX:133MHz:64-bit) MAC address 00:0f:20:f9:29:a1
[    4.484965] tg3 0000:03:01.0: eth0: attached PHY is 5704 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0])
[    4.484970] tg3 0000:03:01.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1]
[    4.484974] tg3 0000:03:01.0: eth0: dma_rwctrl[769f4000] dma_mask[64-bit]
[    4.485072] tg3 0000:03:01.1: enabling device (0140 -> 0142)
[    4.485081] tg3 0000:03:01.1: PCI IRQ 26 -> rerouted to legacy IRQ 18
[    4.485090] tg3 0000:03:01.1: PCI INT B -> GSI 18 (level, low) -> IRQ 18
[    4.490364] lvm[302]: No volume groups found
[    4.530763] tg3 0000:03:01.1: eth1: Tigon3 [partno(N/A) rev 2100] (PCIX:133MHz:64-bit) MAC address 00:0f:20:f9:29:a0
[    4.530772] tg3 0000:03:01.1: eth1: attached PHY is 5704 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0])
[    4.530779] tg3 0000:03:01.1: eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[    4.530785] tg3 0000:03:01.1: eth1: dma_rwctrl[769f4000] dma_mask[64-bit]
[    4.687730] systemd-tmpfiles[452]: Successfully loaded SELinux database in 30ms 107us, size on heap is 476K.
[    4.760231] udevd[275]: renamed network interface eth0 to em1
[    4.781281] udevd[276]: renamed network interface eth1 to em2
[    5.329168] scsi 2:0:0:0: Direct-Access     USB      Flash Disk       1.00 PQ: 0 ANSI: 2
[    5.330446] sd 2:0:0:0: Attached scsi generic sg1 type 0
[    5.337213] sd 2:0:0:0: [sda] 7900336 512-byte logical blocks: (4.04 GB/3.76 GiB)
[    5.340157] sd 2:0:0:0: [sda] Write Protect is off
[    5.340163] sd 2:0:0:0: [sda] Mode Sense: 0b 00 00 08
[    5.343133] sd 2:0:0:0: [sda] No Caching mode page present
[    5.343189] sd 2:0:0:0: [sda] Assuming drive cache: write through
[    5.356145] sd 2:0:0:0: [sda] No Caching mode page present
[    5.356200] sd 2:0:0:0: [sda] Assuming drive cache: write through
[    5.362201]  sda: sda1
[    5.378167] sd 2:0:0:0: [sda] No Caching mode page present
[    5.378221] sd 2:0:0:0: [sda] Assuming drive cache: write through
[    5.378272] sd 2:0:0:0: [sda] Attached SCSI removable disk
[    6.369350] hotplug (510): /proc/510/oom_adj is deprecated, please use /proc/510/oom_score_adj instead.
[    6.428608] Loading iSCSI transport class v2.0-870.
[    6.488339] iscsi: registered transport (tcp)
[    6.513083] Floppy drive(s): fd0 is 1.44M
[    9.528209] floppy0: no floppy controllers found
[    9.563375] BIOS EDD facility v0.16 2004-Jun-25, 3 devices found
[    9.568828] input: PC Speaker as /devices/platform/pcspkr/input/input4
[    9.597888] No iBFT detected.
[   14.144311] ADDRCONF(NETDEV_UP): em1: link is not ready
[   14.637453] ADDRCONF(NETDEV_UP): em2: link is not ready
[   14.920026] tg3 0000:03:01.0: PME# enabled
[   15.731466] tg3 0000:03:01.1: PME# enabled
[   16.116951] ISO 9660 Extensions: Microsoft Joliet Level 3
[   16.121411] ISO 9660 Extensions: RRIP_1991A
[   16.121451] SELinux: initialized (dev sr0, type iso9660), uses genfs_contexts
[   24.561657] md: raid0 personality registered for level 0
[   24.566880] md: raid1 personality registered for level 1
[   24.593495] async_tx: api initialized (async)
[   24.594842] xor: automatically using best checksumming function: generic_sse
[   24.599016]    generic_sse:  4300.000 MB/sec
[   24.599021] xor: using function: generic_sse (4300.000 MB/sec)
[   24.677045] raid6: int64x1   1250 MB/s
[   24.694045] raid6: int64x2   1207 MB/s
[   24.711016] raid6: int64x4   1597 MB/s
[   24.728056] raid6: int64x8   1128 MB/s
[   24.745031] raid6: sse2x1    1769 MB/s
[   24.762025] raid6: sse2x2    2488 MB/s
[   24.779022] raid6: sse2x4    3378 MB/s
[   24.779025] raid6: using algorithm sse2x4 (3378 MB/s)
[   24.783208] md: raid6 personality registered for level 6
[   24.783215] md: raid5 personality registered for level 5
[   24.783219] md: raid4 personality registered for level 4
[   24.796496] md: raid10 personality registered for level 10
[   24.801057] md: linear personality registered for level -1
[   24.820627] device-mapper: multipath: version 1.3.0 loaded
[   24.825044] device-mapper: multipath round-robin: version 1.0.0 loaded

bradycl_84043 · 11-10-2011, 11:53 PM

If anybody can look at the differences in the above and give me any insight as to what is going on, I would be very grateful.

Thanks!

joeg4go · 03-26-2012, 12:10 PM

bradycl_84043,

I ran into somewhat of similar issue on a Proliant DL380 G4 running MS Server 2008 R2, only the OS had been installed and running without issue for 10 months. Last Thursday after installing the latest MS updates the server rebooted and never came back up. After some googling I suspected the IRQ of the smart array 6i had been changed by one of the updates. I noticed when trying to change these settings that the Smart Array 6i IRQ was linked with the IRQ of the USB 1.0 Controller.

At this point I thought I'd upgrade the firmware of the server using the HP Smart Update Utility boot disk. The boot disk is Linux based and also failed to boot. The only message displayed on the screen was “Probing EDD (edd=off to disable).” At this point I tried disabling USB in the bios & rebooted. Still nothing…. then I went back into the bios and changed the IRQ of the Smart Array 6i from 5 to 7. All of the sudden the server had no problem booting the Firmware update utility or the installed operating system.

I too require the machine have USB, so I bought a cheap PCI USB 2.0 Controller for < 20$ and we’re back up and running.

jefro · 03-26-2012, 02:40 PM

I'd be more tempted to run Centos or Scientific linux on that.