drive is dying?

DBabo · 06-06-2010, 10:16 PM

Hello,
it's a relatively (1yo)new drive. Other drives are between 3 to 6 yo (yeah i know).
I'm not sure what's going on. But i did noticed that ls takes lots of time to produce the output. It runs under LVM2 and has ext3. There is plenty of space.
I'm clueless what to think.

Here is the content of the messages:

Code:

Jun  6 23:00:11 server kernel: kjournald starting.  Commit interval 5 seconds
Jun  6 23:00:11 server kernel: EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
Jun  6 23:00:11 server kernel: EXT3 FS on dm-2, internal journal
Jun  6 23:00:11 server kernel: EXT3-fs: mounted filesystem with ordered data mode.
Jun  6 23:06:17 server kernel: ata2: EH in SWNCQ mode,QC:qc_active 0x3 sactive 0x3
Jun  6 23:06:17 server kernel: ata2: SWNCQ:qc_active 0x1 defer_bits 0x2 last_issue_tag 0x0
Jun  6 23:06:17 server kernel:   dhfis 0x1 dmafis 0x1 sdbfis 0x0
Jun  6 23:06:17 server kernel: ata2: ATA_REG 0x41 ERR_REG 0x40
Jun  6 23:06:17 server kernel: ata2: tag : dhfis dmafis sdbfis sacitve
Jun  6 23:06:17 server kernel: ata2: tag 0x0: 1 1 0 1  
Jun  6 23:06:17 server kernel: ata2.00: exception Emask 0x1 SAct 0x3 SErr 0x0 action 0x6 frozen
Jun  6 23:06:17 server kernel: ata2.00: Ata error. fis:0x21
Jun  6 23:06:17 server kernel: ata2.00: cmd 60/08:00:74:f8:50/00:00:74:00:00/40 tag 0 ncq 4096 in
Jun  6 23:06:17 server kernel:          res 41/40:04:74:f8:50/40:00:74:00:00/40 Emask 0x9 (media error)
Jun  6 23:06:17 server kernel: ata2.00: status: { DRDY ERR }
Jun  6 23:06:17 server kernel: ata2.00: error: { UNC }
Jun  6 23:06:17 server kernel: ata2.00: cmd 61/18:08:4c:51:35/00:00:3a:00:00/40 tag 1 ncq 12288 out
Jun  6 23:06:17 server kernel:          res 41/40:04:74:f8:50/40:00:74:00:00/40 Emask 0x9 (media error)
Jun  6 23:06:17 server kernel: ata2.00: status: { DRDY ERR }
Jun  6 23:06:17 server kernel: ata2.00: error: { UNC }
Jun  6 23:06:18 server kernel: ata2: soft resetting link
Jun  6 23:06:18 server kernel: ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Jun  6 23:06:18 server kernel: ata2.00: configured for UDMA/133
Jun  6 23:06:18 server kernel: ata2: EH complete
Jun  6 23:06:18 server kernel: SCSI device sdb: 2930277168 512-byte hdwr sectors (1500302 MB)
Jun  6 23:06:18 server kernel: sdb: Write Protect is off
Jun  6 23:06:18 server kernel: SCSI device sdb: drive cache: write back
Jun  6 23:06:21 server kernel: ata2: EH in SWNCQ mode,QC:qc_active 0x3 sactive 0x3
Jun  6 23:06:21 server kernel: ata2: SWNCQ:qc_active 0x2 defer_bits 0x1 last_issue_tag 0x1
Jun  6 23:06:21 server kernel:   dhfis 0x2 dmafis 0x2 sdbfis 0x1
Jun  6 23:06:21 server kernel: ata2: ATA_REG 0x41 ERR_REG 0x40
Jun  6 23:06:21 server kernel: ata2: tag : dhfis dmafis sdbfis sacitve
Jun  6 23:06:21 server kernel: ata2: tag 0x1: 1 1 0 1  
Jun  6 23:06:21 server kernel: ata2.00: exception Emask 0x1 SAct 0x3 SErr 0x0 action 0x6 frozen
Jun  6 23:06:21 server kernel: ata2.00: Ata error. fis:0x21
Jun  6 23:06:21 server kernel: ata2.00: cmd 61/08:00:64:51:35/00:00:3a:00:00/40 tag 0 ncq 4096 out
Jun  6 23:06:21 server kernel:          res 41/40:0c:74:f8:50/40:00:74:00:00/40 Emask 0x9 (media error)
Jun  6 23:06:21 server kernel: ata2.00: status: { DRDY ERR }
Jun  6 23:06:21 server kernel: ata2.00: error: { UNC }
Jun  6 23:06:21 server kernel: ata2.00: cmd 60/08:08:74:f8:50/00:00:74:00:00/40 tag 1 ncq 4096 in
Jun  6 23:06:21 server kernel:          res 41/40:0c:74:f8:50/40:00:74:00:00/40 Emask 0x9 (media error)
Jun  6 23:06:21 server kernel: ata2.00: status: { DRDY ERR }
Jun  6 23:06:21 server kernel: ata2.00: error: { UNC }
Jun  6 23:06:21 server kernel: ata2: soft resetting link
Jun  6 23:06:21 server kernel: ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Jun  6 23:06:21 server kernel: ata2.00: configured for UDMA/133
Jun  6 23:06:21 server kernel: ata2: EH complete
Jun  6 23:06:21 server kernel: SCSI device sdb: 2930277168 512-byte hdwr sectors (1500302 MB)
Jun  6 23:06:21 server kernel: sdb: Write Protect is off
Jun  6 23:06:21 server kernel: SCSI device sdb: drive cache: write back

i didn't make any config changes to the machine for a long time. Only updates from yum.

Code:

server.home 2.6.18-164.15.1.el5.centos.plus #1 SMP Wed Mar 17 20:01:32 EDT 2010 i686 athlon i386 GNU/Linux

Code:

lspci
00:00.0 RAM memory: nVidia Corporation C51 Host Bridge (rev a2)
00:00.1 RAM memory: nVidia Corporation C51 Memory Controller 0 (rev a2)
00:00.2 RAM memory: nVidia Corporation C51 Memory Controller 1 (rev a2)
00:00.3 RAM memory: nVidia Corporation C51 Memory Controller 5 (rev a2)
00:00.4 RAM memory: nVidia Corporation C51 Memory Controller 4 (rev a2)
00:00.5 RAM memory: nVidia Corporation C51 Host Bridge (rev a2)
00:00.6 RAM memory: nVidia Corporation C51 Memory Controller 3 (rev a2)
00:00.7 RAM memory: nVidia Corporation C51 Memory Controller 2 (rev a2)
00:02.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1)
00:04.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1)
00:09.0 RAM memory: nVidia Corporation MCP51 Host Bridge (rev a2)
00:0a.0 ISA bridge: nVidia Corporation MCP51 LPC Bridge (rev a2)
00:0a.1 SMBus: nVidia Corporation MCP51 SMBus (rev a2)
00:0a.2 RAM memory: nVidia Corporation MCP51 Memory Controller 0 (rev a2)
00:0b.0 USB Controller: nVidia Corporation MCP51 USB Controller (rev a2)
00:0b.1 USB Controller: nVidia Corporation MCP51 USB Controller (rev a2)
00:0d.0 IDE interface: nVidia Corporation MCP51 IDE (rev a1)
00:0e.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev a1)
00:0f.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev a1)
00:10.0 PCI bridge: nVidia Corporation MCP51 PCI Bridge (rev a2)
00:10.2 Multimedia audio controller: nVidia Corporation MCP51 AC97 Audio Controller (rev a2)
00:14.0 Bridge: nVidia Corporation MCP51 Ethernet Controller (rev a1)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
02:00.0 VGA compatible controller: nVidia Corporation GT215 [GeForce GT 240] (rev a2)
02:00.1 Audio device: nVidia Corporation High Definition Audio Controller (rev a1)
03:06.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link)
03:09.0 Communication controller: Agere Systems V.92 56K WinModem (rev 03)

MS3FGX · 06-06-2010, 10:46 PM

Those errors certainly don't look good, no. Have you checked the SMART data for the drive? You should also see if the drive manufacturer offers a diagnostic application to do a more thorough test on the drive and controller.

H_TeXMeX_H · 06-07-2010, 05:07 AM

Well try running smartctl on it, post the output of:

Code:

smartctl -A /dev/sda

Then run a long test and wait for it to finish:

Code:

smartctl -t long /dev/sda

Then post the output of:

Code:

smartctl -a /dev/sda

Change '/dev/sda' to whatever the drive is.

You can also use the manufacturer's diagnostic utility, it's probably on this disk:
http://www.ultimatebootcd.com/

DBabo · 06-07-2010, 11:48 AM

thank you guys. let me get home and run the diags.

DBabo · 06-07-2010, 11:50 AM

Quote:

Originally Posted by H_TeXMeX_H

Well try running smartctl on it, post the output of:
<skip>
You can also use the manufacturer's diagnostic utility, it's probably on this disk:
http://www.ultimatebootcd.com/

looks like a very robust and useful util. Will check it out.

DBabo · 06-07-2010, 08:46 PM

And here we go:

Code:

smartctl -A /dev/sdb
smartctl version 5.38 [i686-redhat-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF READ SMART DATA SECTION ===
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       8394
  3 Spin_Up_Time            0x0027   181   179   021    Pre-fail  Always       -       5925
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       449
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   200   200   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   097   097   000    Old_age   Always       -       2341
 10 Spin_Retry_Count        0x0032   100   100   000    Old_age   Always       -       0
 11 Calibration_Retry_Count 0x0032   100   100   000    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       166
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       59
193 Load_Cycle_Count        0x0032   199   199   000    Old_age   Always       -       3606
194 Temperature_Celsius     0x0022   104   088   000    Old_age   Always       -       46
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   195   195   000    Old_age   Always       -       1308
198 Offline_Uncorrectable   0x0030   200   200   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0008   200   200   000    Old_age   Offline      -       0

and the "-t long" said it will take it ~4 hours to complete. So i'll post the output tomorrow evening.

H_TeXMeX_H · 06-08-2010, 04:28 AM

So far the drive looks fine, it looks to be new and has no signs of failing.

It looks like this is a SATA drive in PATA mode. You could try going into the BIOS and setting it to AHCI mode, this may solve issues related to the pata kernel driver. If you also post the output of 'lspci -vv' we can see which driver it is currently using.

DBabo · 06-08-2010, 06:39 AM

and here is the last portion:

Code:

smartctl -a /dev/sdb
smartctl version 5.38 [i686-redhat-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Device Model:     WDC WD15EADS-00P8B0
Serial Number:    WD-WMAVU0531072
Firmware Version: 01.00A01
User Capacity:    1,500,301,910,016 bytes
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   8
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Tue Jun  8 07:37:50 2010 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x85) Offline data collection activity
                                        was aborted by an interrupting command from host.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      ( 121) The previous self-test completed having
                                        the read element of the test failed.
Total time to complete Offline
data collection:                 (31800) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 255) minutes.
Conveyance self-test routine
recommended polling time:        (   5) minutes.
SCT capabilities:              (0x3037) SCT Status supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       8944
  3 Spin_Up_Time            0x0027   181   179   021    Pre-fail  Always       -       5925
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       449
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   200   200   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   097   097   000    Old_age   Always       -       2351
 10 Spin_Retry_Count        0x0032   100   100   000    Old_age   Always       -       0
 11 Calibration_Retry_Count 0x0032   100   100   000    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       166
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       59
193 Load_Cycle_Count        0x0032   199   199   000    Old_age   Always       -       3607
194 Temperature_Celsius     0x0022   109   088   000    Old_age   Always       -       41
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   195   195   000    Old_age   Always       -       1455
198 Offline_Uncorrectable   0x0030   200   200   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0008   200   200   000    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed: read failure       90%      2342         1951440065

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

what does

Quote:

If Selective self-test is pending on power-up, resume after 0 minute delay.

means?

DBabo · 06-08-2010, 06:41 AM

SATA in PATA mode? uhh that explains why it so slow...

Code:

lspci -vv
00:00.0 RAM memory: nVidia Corporation C51 Host Bridge (rev a2)
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Capabilities: [44] HyperTransport: Slave or Primary Interface
                Command: BaseUnitID=0 UnitCnt=15 MastHost- DefDir- DUL-
                Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
                Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
                Link Control 1: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn+ LSEn+ ExtCTL- 64b-
                Link Config 1: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
                Revision ID: 1.03
                Link Frequency 0: 800MHz
                Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
                Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
                Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
                Link Frequency 1: 800MHz
                Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
                Link Frequency Capability 1: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
                Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
                Prefetchable memory behind bridge Upper: 00-00
                Bus Number: 00
        Capabilities: [e0] HyperTransport: MSI Mapping

00:00.1 RAM memory: nVidia Corporation C51 Memory Controller 0 (rev a2)
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:00.2 RAM memory: nVidia Corporation C51 Memory Controller 1 (rev a2)
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:00.3 RAM memory: nVidia Corporation C51 Memory Controller 5 (rev a2)
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:00.4 RAM memory: nVidia Corporation C51 Memory Controller 4 (rev a2)
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0

00:00.5 RAM memory: nVidia Corporation C51 Host Bridge (rev a2)
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Capabilities: [44] #00 [00fe]
        Capabilities: [fc] #00 [0000]

00:00.6 RAM memory: nVidia Corporation C51 Memory Controller 3 (rev a2)
        Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:00.7 RAM memory: nVidia Corporation C51 Memory Controller 2 (rev a2)
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:02.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0, Cache Line Size: 32 bytes
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        I/O behind bridge: 0000a000-0000afff
        Memory behind bridge: fdb00000-fdbfffff
        Prefetchable memory behind bridge: 00000000fdc00000-00000000fdc00000
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
        Capabilities: [40] #0d [0000]
        Capabilities: [48] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+
                Address: 00000000fee00000  Data: 4041
        Capabilities: [60] HyperTransport: MSI Mapping
        Capabilities: [80] Express Root Port (Slot+) IRQ 0
                Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
                Device: Latency L0s <512ns, L1 <4us
                Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
                Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
                Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 2
                Link: Latency L0s <512ns, L1 <4us
                Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
                Link: Speed 2.5Gb/s, Width x1
                Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
                Slot: Number 0, PowerLimit 0.000000
                Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
                Slot: AttnInd Off, PwrInd On, Power-
                Root: Correctable- Non-Fatal- Fatal- PME-
        Capabilities: [100] Virtual Channel

00:04.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0, Cache Line Size: 32 bytes
        Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
        I/O behind bridge: 0000b000-0000bfff
        Memory behind bridge: fb000000-fcffffff
        Prefetchable memory behind bridge: 00000000b0000000-00000000cff00000
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
        Capabilities: [40] #0d [0000]
        Capabilities: [48] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+
                Address: 00000000fee00000  Data: 4049
        Capabilities: [60] HyperTransport: MSI Mapping
        Capabilities: [80] Express Root Port (Slot+) IRQ 0
                Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
                Device: Latency L0s <512ns, L1 <4us
                Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
                Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
                Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
                Link: Latency L0s <512ns, L1 <4us
                Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
                Link: Speed 2.5Gb/s, Width x16
                Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
                Slot: Number 0, PowerLimit 0.000000
                Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
                Slot: AttnInd Off, PwrInd On, Power-
                Root: Correctable- Non-Fatal- Fatal- PME-
        Capabilities: [100] Virtual Channel

00:09.0 RAM memory: nVidia Corporation MCP51 Host Bridge (rev a2)
        Subsystem: nVidia Corporation Unknown device cb84
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Capabilities: [44] HyperTransport: Slave or Primary Interface
                Command: BaseUnitID=9 UnitCnt=15 MastHost- DefDir- DUL-
                Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn+ LSEn+ ExtCTL- 64b-
                Link Config 0: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
                Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
                Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
                Revision ID: 1.03
                Link Frequency 0: 800MHz
                Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
                Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
                Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
                Link Frequency 1: 200MHz
                Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
                Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
                Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
                Prefetchable memory behind bridge Upper: 00-00
                Bus Number: 00
        Capabilities: [e0] HyperTransport: MSI Mapping

00:0a.0 ISA bridge: nVidia Corporation MCP51 LPC Bridge (rev a2)
        Subsystem: Foxconn International, Inc. Unknown device 0caf
        Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0

00:0a.1 SMBus: nVidia Corporation MCP51 SMBus (rev a2)
        Subsystem: Foxconn International, Inc. Unknown device 0caf
        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin A routed to IRQ 10
        Region 4: I/O ports at 1c00 [size=64]
        Region 5: I/O ports at 1c40 [size=64]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0a.2 RAM memory: nVidia Corporation MCP51 Memory Controller 0 (rev a2)
        Subsystem: Foxconn International, Inc. Unknown device 0caf
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:0b.0 USB Controller: nVidia Corporation MCP51 USB Controller (rev a2) (prog-if 10 [OHCI])
        Subsystem: Foxconn International, Inc. Unknown device 0caf
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0 (750ns min, 250ns max)
        Interrupt: pin A routed to IRQ 11
        Region 0: Memory at fe02f000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0b.1 USB Controller: nVidia Corporation MCP51 USB Controller (rev a2) (prog-if 20 [EHCI])
        Subsystem: Foxconn International, Inc. Unknown device 0caf
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0 (750ns min, 250ns max)
        Interrupt: pin B routed to IRQ 5
        Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [44] Debug port
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0d.0 IDE interface: nVidia Corporation MCP51 IDE (rev a1) (prog-if 8a [Master SecP PriP])
        Subsystem: Foxconn International, Inc. Unknown device 0caf
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0 (750ns min, 250ns max)
        Region 4: I/O ports at f400 [size=16]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0e.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev a1) (prog-if 85 [Master SecO PriO])
        Subsystem: nVidia Corporation Unknown device cb84
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0 (750ns min, 250ns max)
        Interrupt: pin A routed to IRQ 10
        Region 0: I/O ports at 09f0 [size=8]
        Region 1: I/O ports at 0bf0 [size=4]
        Region 2: I/O ports at 0970 [size=8]
        Region 3: I/O ports at 0b70 [size=4]
        Region 4: I/O ports at e000 [size=16]
        Region 5: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [b0] Message Signalled Interrupts: 64bit+ Queue=0/2 Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [cc] HyperTransport: MSI Mapping

00:0f.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev a1) (prog-if 85 [Master SecO PriO])
        Subsystem: nVidia Corporation Unknown device cb84
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0 (750ns min, 250ns max)
        Interrupt: pin A routed to IRQ 11
        Region 0: I/O ports at 09e0 [size=8]
        Region 1: I/O ports at 0be0 [size=4]
        Region 2: I/O ports at 0960 [size=8]
        Region 3: I/O ports at 0b60 [size=4]
        Region 4: I/O ports at cc00 [size=16]
        Region 5: Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [b0] Message Signalled Interrupts: 64bit+ Queue=0/2 Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [cc] HyperTransport: MSI Mapping

00:10.0 PCI bridge: nVidia Corporation MCP51 PCI Bridge (rev a2) (prog-if 01 [Subtractive decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
        I/O behind bridge: 00009000-00009fff
        Memory behind bridge: fde00000-fdefffff
        Prefetchable memory behind bridge: fdd00000-fddfffff
        Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR+
        BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
        Capabilities: [b8] #0d [0000]
        Capabilities: [8c] HyperTransport: MSI Mapping

00:10.2 Multimedia audio controller: nVidia Corporation MCP51 AC97 Audio Controller (rev a2)
        Subsystem: Foxconn International, Inc. Unknown device 0caf
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0 (500ns min, 1250ns max)
        Interrupt: pin C routed to IRQ 11
        Region 0: I/O ports at c800 [size=256]
        Region 1: I/O ports at c400 [size=256]
        Region 2: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:14.0 Bridge: nVidia Corporation MCP51 Ethernet Controller (rev a1)
        Subsystem: Foxconn International, Inc. Unknown device 0caf
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0 (250ns min, 5000ns max)
        Interrupt: pin A routed to IRQ 10
        Region 0: Memory at fe02a000 (32-bit, non-prefetchable) [size=4K]
        Region 1: I/O ports at c000 [size=8]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable+ DSel=0 DScale=0 PME-

00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Capabilities: [80] HyperTransport: Host or Secondary Interface
                !!! Possibly incomplete decoding
                Command: WarmRst+ DblEnd-
                Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
                Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
                Revision ID: 1.02

00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

02:00.0 VGA compatible controller: nVidia Corporation GT215 [GeForce GT 240] (rev a2) (prog-if 00 [VGA controller])
        Subsystem: Micro-Star International Co., Ltd. Unknown device 2072
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 5
        Region 0: Memory at fb000000 (32-bit, non-prefetchable) [size=16M]
        Region 1: Memory at b0000000 (64-bit, prefetchable) [size=256M]
        Region 3: Memory at ce000000 (64-bit, prefetchable) [size=32M]
        Region 5: I/O ports at bc00 [size=128]
        [virtual] Expansion ROM at c0000000 [disabled] [size=512K]
        Capabilities: [60] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [68] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [78] Express Endpoint IRQ 0
                Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
                Device: Latency L0s unlimited, L1 <64us
                Device: AtnBtn- AtnInd- PwrInd-
                Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
                Device: RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
                Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
                Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
                Link: Latency L0s <512ns, L1 <4us
                Link: ASPM Disabled RCB 128 bytes CommClk+ ExtSynch-
                Link: Speed 2.5Gb/s, Width x16
        Capabilities: [b4] Vendor Specific Information
        Capabilities: [100] Virtual Channel
        Capabilities: [128] Power Budgeting
        Capabilities: [600] Unknown (11)

02:00.1 Audio device: nVidia Corporation High Definition Audio Controller (rev a1)
        Subsystem: Micro-Star International Co., Ltd. Unknown device 2072
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0, Cache Line Size: 32 bytes
        Interrupt: pin B routed to IRQ 10
        Region 0: Memory at fcffc000 (32-bit, non-prefetchable) [size=16K]
        Capabilities: [60] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [68] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [78] Express Endpoint IRQ 0
                Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
                Device: Latency L0s <4us, L1 <64us
                Device: AtnBtn- AtnInd- PwrInd-
                Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
                Device: RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
                Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
                Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
                Link: Latency L0s <512ns, L1 <1us
                Link: ASPM L0s L1 Enabled RCB 128 bytes CommClk- ExtSynch-
                Link: Speed 2.5Gb/s, Width x16

03:06.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
        Subsystem: Foxconn International, Inc. Unknown device 0caf
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (500ns min, 1000ns max), Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 10
        Region 0: Memory at fdeff000 (32-bit, non-prefetchable) [size=2K]
        Region 1: Memory at fdef8000 (32-bit, non-prefetchable) [size=16K]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME+

03:09.0 Communication controller: Agere Systems V.92 56K WinModem (rev 03)
        Subsystem: Agere Systems Unknown device 044c
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (63000ns min, 3500ns max)
        Interrupt: pin A routed to IRQ 11
        Region 0: Memory at fdefe000 (32-bit, non-prefetchable) [size=256]
        Region 1: I/O ports at 9c00 [size=8]
        Region 2: I/O ports at 9800 [size=256]
        Capabilities: [f8] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=160mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

H_TeXMeX_H · 06-08-2010, 06:56 AM

Code:

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed: read failure       90%      2342         1951440065

This is not good, this means that there are probably some bad blocks on the drive. Not good news, if the drive is in warrantee you may want to talk to the manufacturer about this. Do run the manufacturer's utils on the drive just to make sure, search for it, or one of the ones on the UBCD might be able to do it.

DBabo · 06-08-2010, 07:14 AM

Quote:

Originally Posted by H_TeXMeX_H

[code]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed

This is not good, this means that there are probably some bad blocks on the drive. Not good news, if the drive is in warrantee you may want to talk to the manufacturer about this. Do run the manufacturer's utils on the drive just to make sure, search for it, or one of the ones on the UBCD might be able to do it.

could this error be due to power save mode, that I set up on the drive? I think it (drive) goes into sleep mode in 30 minutes .
Thank you.

H_TeXMeX_H · 06-08-2010, 07:59 AM

Quote:

Originally Posted by DBabo

could this error be due to power save mode, that I set up on the drive? I think it (drive) goes into sleep mode in 30 minutes .
Thank you.

I don't see how this could be related. Bad blocks mean that the drive is damaged and certain blocks can no longer be used. Sleep mode cannot cause damage. Either the drive has worn out or if it's within warrantee they may replace it because it is faulty.

DBabo · 06-08-2010, 12:16 PM

yeah... the question was more on the "i hope" side of things

Ordered the replacement, at least i happened to have a manuf warranty.
any tools to recover the data ?

H_TeXMeX_H · 06-08-2010, 12:58 PM

Was any data lost ? Did it die already ? If it didn't, just copy the data out. If it did die, then use testdisk of foremost to try and recover it.

chadwick · 06-08-2010, 01:20 PM

Quote:

Originally Posted by DBabo

any tools to recover the data ?

This past weekend I had an issue with my hard drive which is 4 years old and had developed some bad sectors. The drive was for the most part useable, but when I tried to resize one of the partitions it would fail. I downloaded the program HDD Regenerator which magically seems to have gotten rid of the physically bad sectors on the drive and allowed me to proceed at least up until the present without any problems. I used the free trial version which allows you to repair one bad sector per boot of the computer, assuming the sector is repairable.

It's not open source, so it requires trust on your part in order to use it, but my experience with it was positive. In my case the manufacturers' (Hitachi and Lenovo) CDs were not able to repair the drive but this one was. If you have crucial data on that drive and you can't get it to work, and the manufacturer's repair utility doesn't work to fix it, then it's possible you could try something like that.