Display restricted to 800X600 for intel D845GLAD board with no Graphics card

Dariis · 09-25-2007, 10:05 AM

Hey all i have an Intel D845GLAD mainboard with no slot for graphics card. My display is restricted to 800x600 in simply mepis 6.0 where in RH9 it was more then that ... I have 256+128 RAM and samsung syncmaster 551v monitor plz reply how can i improve my system resolution ????

Wim Sturkenboom · 09-25-2007, 10:28 AM

Some of the points to check in the file /etc/X11/xorg.conf:

HorizSync and VertRefresh lines in the monitor section; the values must match those of your monitor (read manual or find them on the internet)
resolutions in the display subsections of the section screen

Please post the sections device, monitor and screen of above file if you don't come right.

Dariis · 09-25-2007, 02:31 PM

Section "Monitor"
Identifier "Monitor0"
VendorName "unknown"
ModelName "unknown"
#Option "DPMS" "true"
HorizSync 30.0 - 75.0 # Warning: This may fry old Monitors
VertRefresh 50.0 - 70.0 # Very conservative. May flicker.
Modeline "640x480" 25.175 640 664 760 800 480 491 493 525 #60Hz
Modeline "800x600" 40.12 800 848 968 1056 600 601 605 628 #60Hz
Modeline "1024x768" 75 1024 1048 1184 1328 768 771 777 806 -hsync -vsync
Modeline "1024x768" 85 1024 1056 1152 1360 768 784 787 823
ModeLine "1152x864" 65 1152 1168 1384 1480 864 865 875 985 Interlace
Modeline "1152x864" 92 1152 1208 1368 1474 864 865 875 895
Modeline "1152x864" 110 1152 1240 1324 1552 864 864 876 908
Modeline "1152x864" 135 1152 1464 1592 1776 864 864 876 908
Modeline "1152x864" 137.65 1152 1184 1312 1536 864 866 885 902 -HSync -VSync
Modeline "1280x768" 80.14 1280 1344 1480 1680 768 769 772 795
ModeLine "1280x800" 80.58 1280 1344 1480 1680 800 801 804 827 -HSync -VSync
Modeline "1280x1024" 80 1280 1296 1512 1568 1024 1025 1037 1165 Interlace
Modeline "1280x1024" 110 1280 1328 1512 1712 1024 1025 1028 1054
Modeline "1280x1024" 126.5 1280 1312 1472 1696 1024 1032 1040 1068 -HSync -VSync
Modeline "1280x1024" 135 1280 1312 1456 1712 1024 1027 1030 1064
Modeline "1280x1024" 135 1280 1312 1416 1664 1024 1027 1030 1064
Modeline "1280x1024" 157.5 1280 1344 1504 1728 1024 1025 1028 1072 +HSync +VSync
Modeline "1280x1024" 181.75 1280 1312 1440 1696 1024 1031 1046 1072 -HSync -VSync
Modeline "1440x900" 106.47 1440 1520 1672 1904 900 901 904 932 +HSync +VSync
Modeline "1400x1050" 129 1400 1464 1656 1960 1050 1051 1054 1100 +HSync +VSync
Modeline "1600x1200" 162 1600 1664 1856 2160 1200 1201 1204 1250 +HSync +VSync
Modeline "1600x1200" 189 1600 1664 1856 2160 1200 1201 1204 1250 -HSync -VSync
Modeline "1600x1200" 202.5 1600 1664 1856 2160 1200 1201 1204 1250 +HSync +VSync
Modeline "1600x1200" 220 1600 1616 1808 2080 1200 1204 1207 1244 +HSync +VSync
Modeline "1680x1050" 147.14 1680 1784 1968 2256 1050 1051 1054 1087
ModeLine "1800x1440" 230 1800 1896 2088 2392 1440 1441 1444 1490 +HSync +VSync
ModeLine "1800x1440" 250 1800 1896 2088 2392 1440 1441 1444 1490 +HSync +VSync
Modeline "1920x1200" 230 1920 1936 2096 2528 1200 1201 1204 1250 +HSync +VSync
EndSection

Section "Monitor"
Identifier "ATIMonitor"
VendorName "unknown"
ModelName "unknown"
#Option "DPMS" "true"
HorizSync 30.0 - 75.0 # Warning: This may fry old Monitors
VertRefresh 50.0 - 70.0 # Very conservative. May flicker.
EndSection

Section "Device"
Identifier "Card0"
Driver "i810"
BoardName "unknown"

#BusID "PCI:1:0:0"
#Option "sw_cursor" # needed for some ati cards
#Option "hw_cursor"
#Option "NoAccel"
#Option "ShowCache"
#Option "ShadowFB"
#Option "UseFBDev"
#Option "Rotate"
Option "UseInternalAGPGART" "no"
# nvidia special options, use with care
Option "CursorShadow" "1"
Option "CursorShadowAlpha" "63"
Option "CursorShadowYOffset" "2"
Option "CursorShadowXOffset" "4"
Option "FlatPanelProperties" "Scaling = native"
Option "NoLogo" "false"
Option "IgnoreEdid" "true" # needs to be true for some nvidia cards
EndSection

Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultColorDepth 16

SubSection "Display"
Depth 8
Modes "800x600"
EndSubSection
SubSection "Display"
Depth 15
Modes "800x600"
EndSubSection
SubSection "Display"
Depth 16
Modes "800x600"
EndSubSection
SubSection "Display"
Depth 24
Modes "800x600"
EndSubSection
SubSection "Display"
Depth 32
Modes "800x600"
EndSubSection

# Only the official NVIDIA driver supports twinview
# these setting are an example
Option "TwinView" "false"
Option "SecondMonitorVendorName" "unknown"
Option "SecondMonitorModelName" "unknown"
Option "SecondMonitorHorizSync" "30-75"
Option "SecondMonitorVertRefresh" "50-70"
#Option "MetaModes" "1024x768, 1024x768"
Option "TwinViewOrientation" "RightOf"
Option "ConnectedMonitor" "dfp,dfp"
EndSection

Section "Screen"
Identifier "ATIScreen"
Device "Card0"
Monitor "ATIMonitor"
DefaultColorDepth 24

SubSection "Display"
Depth 24
Modes "800x600"
EndSubSection
EndSection

Section "DRI"
Mode 0666
EndSection

GrapefruiTgirl · 09-25-2007, 03:29 PM

In your monitor section for 'Monitor0', definitely replace the horizsync and vertrefresh rates to match the manufacturers specs of your monitor.

Also, while the first choice of the X server should be the Modelines, you ought to add other resolutions that you want, in the 'Screen' section, where "800x600" is the only resolution provided.

Basically, this should fix the problems of A) the V + H ranges are limiting your resolution, and B) the only modes provided in the Screen section is "800x600".

Wim Sturkenboom · 09-25-2007, 11:28 PM

OK, there must also be a section ServerLayout; Please post that as well as you have about everything double.
I assume that Screen0 is currently used as it refers to a device with identifier Card0.

Code:

Section "Monitor"
Identifier "Monitor0"
VendorName "unknown"
ModelName "unknown"

HorizSync 30.0 - 75.0
VertRefresh 50.0 - 70.0

#Option "DPMS" "true"
HorizSync 30.0 - 75.0 # Warning: This may fry old Monitors
VertRefresh 50.0 - 70.0 # Very conservative. May flicker.
Modeline "640x480" 25.175 640 664 760 800 480 491 493 525 #60Hz
Modeline "800x600" 40.12 800 848 968 1056 600 601 605 628 #60Hz
Modeline "1024x768" 75 1024 1048 1184 1328 768 771 777 806 -hsync -vsync
Modeline "1024x768" 85 1024 1056 1152 1360 768 784 787 823
ModeLine "1152x864" 65 1152 1168 1384 1480 864 865 875 985 Interlace
Modeline "1152x864" 92 1152 1208 1368 1474 864 865 875 895
Modeline "1152x864" 110 1152 1240 1324 1552 864 864 876 908
Modeline "1152x864" 135 1152 1464 1592 1776 864 864 876 908
Modeline "1152x864" 137.65 1152 1184 1312 1536 864 866 885 902 -HSync -VSync
Modeline "1280x768" 80.14 1280 1344 1480 1680 768 769 772 795
ModeLine "1280x800" 80.58 1280 1344 1480 1680 800 801 804 827 -HSync -VSync
Modeline "1280x1024" 80 1280 1296 1512 1568 1024 1025 1037 1165 Interlace
Modeline "1280x1024" 110 1280 1328 1512 1712 1024 1025 1028 1054
Modeline "1280x1024" 126.5 1280 1312 1472 1696 1024 1032 1040 1068 -HSync -VSync
Modeline "1280x1024" 135 1280 1312 1456 1712 1024 1027 1030 1064
Modeline "1280x1024" 135 1280 1312 1416 1664 1024 1027 1030 1064
Modeline "1280x1024" 157.5 1280 1344 1504 1728 1024 1025 1028 1072 +HSync +VSync
Modeline "1280x1024" 181.75 1280 1312 1440 1696 1024 1031 1046 1072 -HSync -VSync
Modeline "1440x900" 106.47 1440 1520 1672 1904 900 901 904 932 +HSync +VSync
Modeline "1400x1050" 129 1400 1464 1656 1960 1050 1051 1054 1100 +HSync +VSync
Modeline "1600x1200" 162 1600 1664 1856 2160 1200 1201 1204 1250 +HSync +VSync
Modeline "1600x1200" 189 1600 1664 1856 2160 1200 1201 1204 1250 -HSync -VSync
Modeline "1600x1200" 202.5 1600 1664 1856 2160 1200 1201 1204 1250 +HSync +VSync
Modeline "1600x1200" 220 1600 1616 1808 2080 1200 1204 1207 1244 +HSync +VSync
Modeline "1680x1050" 147.14 1680 1784 1968 2256 1050 1051 1054 1087
ModeLine "1800x1440" 230 1800 1896 2088 2392 1440 1441 1444 1490 +HSync +VSync
ModeLine "1800x1440" 250 1800 1896 2088 2392 1440 1441 1444 1490 +HSync +VSync
Modeline "1920x1200" 230 1920 1936 2096 2528 1200 1201 1204 1250 +HSync +VSync
EndSection

Add the red lines to Monitor0 and adjust the values to reflect the capabilities of your monitor.

Code:

Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultColorDepth 16

SubSection "Display"
Depth 8
Modes "800x600"
EndSubSection
SubSection "Display"
Depth 15
Modes "800x600"
EndSubSection
SubSection "Display"
Depth 16
Modes "1024x768" "800x600"
EndSubSection
SubSection "Display"
Depth 24
Modes "800x600"
EndSubSection
SubSection "Display"
Depth 32
Modes "800x600"
EndSubSection

You're using a depth of 16 (see bold), so add the resolutions that you want to the display subsection for depth 16 (see red text); add other resolutions that you want to use and are supported by your monitor.

Dariis · 09-26-2007, 10:41 AM

Section "ServerLayout"
Identifier "XFree86 Configured"
Screen 0 "Screen0" 0 0
#Screen 0 "ATIScreen" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "PS/2 Mouse" "CorePointer"
#InputDevice "USB Mouse" "CorePointer"
#InputDevice "Touchpad" "CorePointer"
#InputDevice "Stylus" "CorePointer"
#InputDevice "Eraser" "CorePointer"
#InputDevice "Cursor" "CorePointer"
#InputDevice "Serial Mouse" "CorePointer"
EndSection

Section "ServerFlags"
Option "AllowMouseOpenFail" "true"
EndSection

Dariis · 09-26-2007, 11:06 AM

OMG I have done that setting in xorg.conf file there is an option for 1024x768 but it is not showing for 1152x864 and also my desktop is now moving ie it is going out of the screen borders. I have to move my mouse so that i am able c rest of the desktop. Can it be limited to my screen size.

Dariis · 09-30-2007, 02:20 PM

come on ppl dont leave me like that .... help solve ma problem

GrapefruiTgirl · 09-30-2007, 02:47 PM

I'm curious.. You only use ONE monitor, correct? If so, where did this xorg.conf file come from? It looks like it came from a totally different system than yours.

Anyhow, what have you done so far, using the above suggestions from myself and Wim, to try to get this working? And how is it working now?
Perhaps it would be helpful at this point, to either EDIT one of your above posts, or give us a new post, containing your WHOLE, CURRENT xorg.conf file. Let's see what it looks like now.

Dariis · 10-05-2007, 01:18 PM

Section "ServerLayout"
Identifier "XFree86 Configured"
Screen 0 "Screen0" 0 0
#Screen 0 "ATIScreen" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "PS/2 Mouse" "CorePointer"
#InputDevice "USB Mouse" "CorePointer"
#InputDevice "Touchpad" "CorePointer"
#InputDevice "Stylus" "CorePointer"
#InputDevice "Eraser" "CorePointer"
#InputDevice "Cursor" "CorePointer"
#InputDevice "Serial Mouse" "CorePointer"
EndSection

Section "ServerFlags"
Option "AllowMouseOpenFail" "true"
EndSection

Section "Files"
# Xorg 7.0 font paths
FontPath "/usr/share/X11/fonts/misc:unscaled"
FontPath "/usr/share/X11/fonts/cyrillic"
FontPath "/usr/share/X11/fonts/Type1"
FontPath "/usr/share/X11/fonts/util"

# Legacy font paths
FontPath "/usr/X11R6/lib/X11/fonts/misc:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/cyrillic"
FontPath "/usr/X11R6/lib/X11/fonts/Type1"
FontPath "/usr/X11R6/lib/X11/fonts/util"

# Other font paths
FontPath "/usr/share/fonts/truetype/ttf-lucida"
FontPath "/usr/share/fonts/truetype/arphic"
FontPath "/usr/share/fonts/truetype/freefont"
FontPath "/usr/share/fonts/truetype/kochi"
FontPath "/usr/share/fonts/truetype/latex-xft-fonts"
FontPath "/usr/share/fonts/truetype/openoffice"
FontPath "/usr/share/fonts/truetype/ttf-bitstream-vera"
FontPath "/usr/share/fonts/type1/gsfonts"
FontPath "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType"
FontPath "/var/lib/defoma/x-ttcidfont-conf.d/dirs/CID"

EndSection

Section "Module"
Load "GLcore"
Load "bitmap"
Load "dbe"
Load "ddc"
Load "dri"
Load "extmod"
Load "freetype"
Load "glx"
Load "int10"
Load "record"
Load "type1"
Load "v4l"
Load "vbe"
Load "synaptics"
EndSection

Section "InputDevice"
Identifier "Keyboard0"
Driver "keyboard"
Option "CoreKeyboard"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"
Option "XKbOptions" ""
EndSection

Section "InputDevice"
Identifier "Serial Mouse"
Driver "mouse"
Option "Protocol" "Microsoft"
Option "Device" "/dev/ttyS0"
Option "Emulate3Buttons" "false"
Option "Emulate3Timeout" "70"
EndSection

Section "InputDevice"
Identifier "Touchpad"
Driver "synaptics"
Option "Device" "/dev/psaux"
Option "Protocol" "auto-dev"
Option "LeftEdge" "1700"
Option "RightEdge" "5300"
Option "TopEdge" "1700"
Option "BottomEdge" "4200"
Option "FingerLow" "25"
Option "FingerHigh" "30"
Option "MaxTapTime" "180"
Option "MaxTapMove" "220"
Option "VertScrollDelta" "100"
Option "MinSpeed" "0.06"
Option "MaxSpeed" "0.12"
Option "AccelFactor" "0.0010"
Option "SHMConfig" "on"
Option "Repeater" "/dev/input/mice"
EndSection

Section "InputDevice"
Identifier "PS/2 Mouse"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/psaux"
Option "Emulate3Buttons" "false"
Option "Emulate3Timeout" "70"
Option "ZAxisMapping" "4 5"
Option "Buttons" "5"
EndSection

Section "InputDevice"
Identifier "USB Mouse"
Driver "mouse"
Option "Device" "/dev/input/mice"
Option "Protocol" "ExplorerPS/2"
Option "ZAxisMapping" "4 5"
Option "Buttons" "5"
EndSection

Section "InputDevice"
Identifier "Stylus"
Driver "wacom"
Option "Mode" "Absolute"
Option "Type" "stylus"
Option "Device" "/dev/input/wacom"
Endsection

# Settings for wacom eraser
Section "InputDevice"
Identifier "Eraser"
Driver "wacom"
Option "Mode" "Absolute"
Option "Type" "eraser"
Option "Device" "/dev/input/wacom"
Endsection
# Settings for wacom cursor (mouse)
Section "InputDevice"
Identifier "Cursor"
Driver "wacom"
Option "Mode" "Absolute"
Option "Type" "cursor"
Option "Device" "/dev/input/wacom"
Endsection

Section "Monitor"
Identifier "Monitor0"
VendorName "Samsung"
ModelName "SyncMaster 515V"

HorizSync 30.0 - 75.0
VertRefresh 50.0 - 70.0

#Option "DPMS" "true"
HorizSync 30.0
VertRefresh 50.0
Modeline "640x480" 25.175 640 664 760 800 480 491 493 525 #60Hz
Modeline "800x600" 40.12 800 848 968 1056 600 601 605 628 #60Hz
Modeline "1024x768" 75 1024 1048 1184 1328 768 771 777 806 -hsync -vsync
Modeline "1024x768" 85 1024 1056 1152 1360 768 784 787 823
ModeLine "1152x864" 65 1152 1168 1384 1480 864 865 875 985 Interlace
Modeline "1152x864" 92 1152 1208 1368 1474 864 865 875 895
Modeline "1152x864" 110 1152 1240 1324 1552 864 864 876 908
Modeline "1152x864" 135 1152 1464 1592 1776 864 864 876 908
Modeline "1152x864" 137.65 1152 1184 1312 1536 864 866 885 902 -HSync -VSync
Modeline "1280x768" 80.14 1280 1344 1480 1680 768 769 772 795
ModeLine "1280x800" 80.58 1280 1344 1480 1680 800 801 804 827 -HSync -VSync
Modeline "1280x1024" 80 1280 1296 1512 1568 1024 1025 1037 1165 Interlace
Modeline "1280x1024" 110 1280 1328 1512 1712 1024 1025 1028 1054
Modeline "1280x1024" 126.5 1280 1312 1472 1696 1024 1032 1040 1068 -HSync -VSync
Modeline "1280x1024" 135 1280 1312 1456 1712 1024 1027 1030 1064
Modeline "1280x1024" 135 1280 1312 1416 1664 1024 1027 1030 1064
Modeline "1280x1024" 157.5 1280 1344 1504 1728 1024 1025 1028 1072 +HSync +VSync
Modeline "1280x1024" 181.75 1280 1312 1440 1696 1024 1031 1046 1072 -HSync -VSync
Modeline "1440x900" 106.47 1440 1520 1672 1904 900 901 904 932 +HSync +VSync
Modeline "1400x1050" 129 1400 1464 1656 1960 1050 1051 1054 1100 +HSync +VSync
Modeline "1600x1200" 162 1600 1664 1856 2160 1200 1201 1204 1250 +HSync +VSync
Modeline "1600x1200" 189 1600 1664 1856 2160 1200 1201 1204 1250 -HSync -VSync
Modeline "1600x1200" 202.5 1600 1664 1856 2160 1200 1201 1204 1250 +HSync +VSync
Modeline "1600x1200" 220 1600 1616 1808 2080 1200 1204 1207 1244 +HSync +VSync
Modeline "1680x1050" 147.14 1680 1784 1968 2256 1050 1051 1054 1087
ModeLine "1800x1440" 230 1800 1896 2088 2392 1440 1441 1444 1490 +HSync +VSync
ModeLine "1800x1440" 250 1800 1896 2088 2392 1440 1441 1444 1490 +HSync +VSync
Modeline "1920x1200" 230 1920 1936 2096 2528 1200 1201 1204 1250 +HSync +VSync
EndSection

Section "Monitor"
Identifier "ATIMonitor"
VendorName "Samsung"
ModelName "SyncMaster 515V"
#Option "DPMS" "true"
HorizSync 30.0
VertRefresh 50.0
EndSection

Section "Device"
Identifier "Card0"
Driver "i810"
BoardName "unknown"

#BusID "PCI:1:0:0"
#Option "sw_cursor" # needed for some ati cards
#Option "hw_cursor"
#Option "NoAccel"
#Option "ShowCache"
#Option "ShadowFB"
#Option "UseFBDev"
#Option "Rotate"
Option "UseInternalAGPGART" "no"

# savage special options, use with care
#Option "NoUseBios"
#Option "BusType" "PCI"
Option "DmaMode" "None"

# nvidia special options, use with care
Option "CursorShadow" "1"
Option "CursorShadowAlpha" "63"
Option "CursorShadowYOffset" "2"
Option "CursorShadowXOffset" "4"
Option "FlatPanelProperties" "Scaling = native"
Option "NoLogo" "false"
Option "IgnoreEdid" "true" # needs to be true for some nvidia cards
EndSection

Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultColorDepth 16

SubSection "Display"
Depth 8
Modes "800x600"
EndSubSection
SubSection "Display"
Depth 15
Modes "800x600"
EndSubSection
SubSection "Display"
Depth 16
Modes "800x600" "1024x768" "1152x864"
EndSubSection
SubSection "Display"
Depth 24
Modes "800x600"
EndSubSection
SubSection "Display"
Depth 32
Modes "800x600" "1024x768" "1152x864"
EndSubSection

# Only the official NVIDIA driver supports twinview
# these setting are an example
Option "TwinView" "false"
Option "SecondMonitorVendorName" "unknown"
Option "SecondMonitorModelName" "unknown"
Option "SecondMonitorHorizSync" "30-75"
Option "SecondMonitorVertRefresh" "50-70"
#Option "MetaModes" "1024x768, 1024x768"
Option "TwinViewOrientation" "RightOf"
Option "ConnectedMonitor" "dfp,dfp"
EndSection

Section "Screen"
Identifier "ATIScreen"
Device "Card0"
Monitor "ATIMonitor"
DefaultColorDepth 24

SubSection "Display"
Depth 24
Modes "800x600"
EndSubSection
EndSection

Section "DRI"
Mode 0666
EndSection

Dariis · 10-05-2007, 01:22 PM

I have added 1152x864 but it aint working ie it is not shown plus the above setting make my screen go beyond monitor screen so i have to move my mouse to get to rest of the screen. Also if set it back to 800x600 and reboot then that setting is lost and 1024x768 is reset ......

Wim Sturkenboom · 10-08-2007, 12:14 AM

According to http://www.samsung.com/za/products/m...Specifications, your monitor can not do 1152x864. In which case it makes sense that you get a virtual screen and you have to move your mouse 'outside' the monitor to see the rest.

Further there are two sets for HorizSync and VerRefresh in your Monitor0 section; I'm not sure which one will be used by xorg (probably the first one). However, both don't match the specs of your monitor. Please be aware that the values that I gave where just examples.

Code:

HorizSync 30.0 - 55.0
VertRefresh 50.0 - 120.0
#Option "DPMS" "true"
HorizSync 30.0
VertRefresh 50.0

The blue lines contain the correct values (according to above link), the red lines can be removed.

How do you set it 'back' to 800x600? Using some graphical tool? It's possible that X uses the highest resolution by default regardless of the sequence in the modelines (I'm not sure).

Dariis · 10-10-2007, 06:35 PM

yup i use graphical tools by simply right clicking the desktop and setting it to 800x600

sonichedgehog · 10-20-2007, 04:45 AM

Using Debian, all fine, but unable to change above using screen res. preferences (no options there). Old monitor, tried but failed to get info- should I stop at this point?? Xorg.conf has all the options for screen sizes under "modes" so no clue there- started to look at GDM but I'm wallowing. Any suggestions please please?

Wim Sturkenboom · 10-21-2007, 11:07 PM

Which driver in device section? vesa will (only) go to 1024x768, vga even lower.

If your monitor refresh rates are set correctly in the monitor section in xorg.conf, you can add Option "UseEdidFreqs" "False" to the device section. If that does not help, add Option "UseEdid" "False" to the device section.

Please post make and model for both the videocard and the monitor if you don't come right.