LinuxQuestions.org
Register a domain and help support LQ
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Hardware
User Name
Password
Linux - Hardware This forum is for Hardware issues.
Having trouble installing a piece of hardware? Want to know if that peripheral is compatible with Linux?

Notices

Reply
 
Search this Thread
Old 06-10-2002, 05:36 PM   #1
ngomong
Member
 
Registered: Apr 2002
Posts: 54

Rep: Reputation: 15
CD writing errors... it used to work fine.


I'm trying to burn a set of CDs... I got through the first 3 without problems, but now my SCSI bus keeps resetting in the middle. Here is my cdrecord output.
Code:
Cdrecord 1.10 (i686-pc-linux-gnu) Copyright (C) 1995-2001 Jörg Schilling
TOC Type: 1 = CD-ROM
scsidev: '0,4,0'
scsibus: 0 target: 4 lun: 0
Linux sg driver version: 3.1.20
Using libscg version 'schily-0.5'
atapi: 0
Device type    : Removable CD-ROM
Version        : 2
Response Format: 2
Capabilities   : SYNC 
Vendor_info    : 'YAMAHA  '
Identifikation : 'CRW8824S        '
Revision       : '1.00'
Device seems to be: Generic mmc CD-RW.
Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
Driver flags   : SWABAUDIO
Drive buf size : 3172848 = 3098 KB
FIFO size      : 4194304 = 4096 KB
Track 01: data  642 MB        
Total size:     737 MB (73:05.09) = 328882 sectors
Lout start:     738 MB (73:07/07) = 328882 sectors
Current Secsize: 2048
ATIP info from disk:
  Indicated writing power: 5
  Is not unrestricted
  Is not erasable
  Disk sub type: Medium Type A, low Beta category (A-) (2)
  ATIP start of lead in:  -11634 (97:26/66)
  ATIP start of lead out: 359848 (79:59/73)
Disk type:    Short strategy type (Phthalocyanine or similar)
Manuf. index: 3
Manufacturer: CMC Magnetics Corporation
Blocks total: 359848 Blocks current: 359848 Blocks remaining: 30966
Starting to write CD/DVD at speed 8 in write mode for single session.
Last chance to quit, starting real write in 0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...
Starting new track at sector: 0
Track 01: 112 of 648 MB written (fifo 100%).cdrecord: Input/output error. write_g1: scsi sendcmd: no error
CDB:  2A 00 00 00 E1 F6 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 06 00 00 00 00 0A 00 00 00 00 29 00 00 00
Sense Key: 0x6 Unit Attention, Segment 0
Sense Code: 0x29 Qual 0x00 (power on, reset, or bus device reset occurred) Fru 0x0
Sense flags: Blk 0 (not valid) 
cmd finished after 42.517s timeout 40s
write track data: error after 118468608 bytes
Sense Bytes: 70 00 00 00 00 00 00 0A 00 00 00 00 00 00 00 00 00 00
Writing  time:  254.880s
Fixating...
cdrecord: Input/output error. close track/session: scsi sendcmd: no error
CDB:  5B 00 02 00 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 64 00 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x64 Qual 0x00 (illegal mode for this track) Fru 0x0
Sense flags: Blk 0 (not valid) 
cmd finished after 0.783s timeout 480s
cmd finished after 0.783s timeout 480s
Fixating time:    0.786s
cdrecord: fifo had 1930 puts and 1867 gets.
cdrecord: fifo was 0 times empty and 1835 times full, min fill was 95%.
What would be causing this? It happens at different spots each time. Sometimes at the beginning, sometimes near the end. I've tried burning at a slower speed, and that hasn't helped. I tried swapping drives.

What's going on?

Last edited by ngomong; 06-10-2002 at 05:42 PM.
 
Old 06-10-2002, 06:18 PM   #2
Praetorian
Member
 
Registered: Jun 2002
Distribution: Ubuntu
Posts: 31

Rep: Reputation: 16
I'd like to know too. I was able to burn 2 cds in Mandrake 8.2 and on the 3rd it produced a coaster like this. The same thing happened when I tried another cd. I'm using an LSI dual channel SCSI 2 card and an HP 9200i cd-rw. I've got Slackware 8.0 on right now (had it on for a few days) and I haven't tried burning a cd yet.

Last edited by Praetorian; 06-10-2002 at 06:33 PM.
 
Old 06-13-2002, 11:27 PM   #3
Praetorian
Member
 
Registered: Jun 2002
Distribution: Ubuntu
Posts: 31

Rep: Reputation: 16
^bump^
 
Old 06-14-2002, 10:34 AM   #4
neo77777
LQ Addict
 
Registered: Dec 2001
Location: Brooklyn, NY
Distribution: *NIX
Posts: 3,704

Rep: Reputation: 55
mdah, and my CD-burner went to a trash can, pitty.
 
Old 06-15-2002, 04:14 PM   #5
ngomong
Member
 
Registered: Apr 2002
Posts: 54

Original Poster
Rep: Reputation: 15
I swapped in a new SCSI card (which a friend had) and a new burner, and all worked fine. So, I'm not sure which was causing the problems.

I've been switching back to the old SCSI card (because I needed it's bootable-CD capabilities), and it's been fine reading loads of data from it. I'll try burning with it again, and see what happens.
 
Old 06-15-2002, 04:39 PM   #6
Praetorian
Member
 
Registered: Jun 2002
Distribution: Ubuntu
Posts: 31

Rep: Reputation: 16
If I still get problems I'm going to change back to my Initio card. I'll reply to this once I get some cds and do a burn...
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
some applications died when I use ssh when others work fine calix Linux - Networking 1 01-20-2005 06:43 PM
cant work on terminals even though GUI works just fine! vishi_1982 Linux - Newbie 1 07-20-2004 03:07 PM
G++ compiles fine but program does not work MaddDog696 Programming 3 04-15-2004 06:39 PM
DHCP fine for home computer, but not work arobinson74 Linux - Networking 2 03-22-2004 08:47 AM
Dotted quads work fine - URL's don't! purpleandblack Linux - Networking 2 08-18-2003 03:05 PM


All times are GMT -5. The time now is 01:23 AM.

Main Menu
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
identi.ca: @linuxquestions
Facebook: linuxquestions Google+: linuxquestions
Open Source Consulting | Domain Registration