LinuxQuestions.org

LinuxQuestions.org (/questions/)
-   Linux - Hardware (http://www.linuxquestions.org/questions/linux-hardware-18/)
-   -   CD writing errors... it used to work fine. (http://www.linuxquestions.org/questions/linux-hardware-18/cd-writing-errors-it-used-to-work-fine-23082/)

ngomong 06-10-2002 05:36 PM

CD writing errors... it used to work fine.
 
I'm trying to burn a set of CDs... I got through the first 3 without problems, but now my SCSI bus keeps resetting in the middle. Here is my cdrecord output.
Code:

Cdrecord 1.10 (i686-pc-linux-gnu) Copyright (C) 1995-2001 Jörg Schilling
TOC Type: 1 = CD-ROM
scsidev: '0,4,0'
scsibus: 0 target: 4 lun: 0
Linux sg driver version: 3.1.20
Using libscg version 'schily-0.5'
atapi: 0
Device type    : Removable CD-ROM
Version        : 2
Response Format: 2
Capabilities  : SYNC
Vendor_info    : 'YAMAHA  '
Identifikation : 'CRW8824S        '
Revision      : '1.00'
Device seems to be: Generic mmc CD-RW.
Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
Driver flags  : SWABAUDIO
Drive buf size : 3172848 = 3098 KB
FIFO size      : 4194304 = 4096 KB
Track 01: data  642 MB       
Total size:    737 MB (73:05.09) = 328882 sectors
Lout start:    738 MB (73:07/07) = 328882 sectors
Current Secsize: 2048
ATIP info from disk:
  Indicated writing power: 5
  Is not unrestricted
  Is not erasable
  Disk sub type: Medium Type A, low Beta category (A-) (2)
  ATIP start of lead in:  -11634 (97:26/66)
  ATIP start of lead out: 359848 (79:59/73)
Disk type:    Short strategy type (Phthalocyanine or similar)
Manuf. index: 3
Manufacturer: CMC Magnetics Corporation
Blocks total: 359848 Blocks current: 359848 Blocks remaining: 30966
Starting to write CD/DVD at speed 8 in write mode for single session.
Last chance to quit, starting real write in 0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...
Starting new track at sector: 0
Track 01: 112 of 648 MB written (fifo 100%).cdrecord: Input/output error. write_g1: scsi sendcmd: no error
CDB:  2A 00 00 00 E1 F6 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 06 00 00 00 00 0A 00 00 00 00 29 00 00 00
Sense Key: 0x6 Unit Attention, Segment 0
Sense Code: 0x29 Qual 0x00 (power on, reset, or bus device reset occurred) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 42.517s timeout 40s
write track data: error after 118468608 bytes
Sense Bytes: 70 00 00 00 00 00 00 0A 00 00 00 00 00 00 00 00 00 00
Writing  time:  254.880s
Fixating...
cdrecord: Input/output error. close track/session: scsi sendcmd: no error
CDB:  5B 00 02 00 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 64 00 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x64 Qual 0x00 (illegal mode for this track) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.783s timeout 480s
cmd finished after 0.783s timeout 480s
Fixating time:    0.786s
cdrecord: fifo had 1930 puts and 1867 gets.
cdrecord: fifo was 0 times empty and 1835 times full, min fill was 95%.

What would be causing this? It happens at different spots each time. Sometimes at the beginning, sometimes near the end. I've tried burning at a slower speed, and that hasn't helped. I tried swapping drives.

What's going on?

Praetorian 06-10-2002 06:18 PM

I'd like to know too. I was able to burn 2 cds in Mandrake 8.2 and on the 3rd it produced a coaster like this. The same thing happened when I tried another cd. :mad: I'm using an LSI dual channel SCSI 2 card and an HP 9200i cd-rw. I've got Slackware 8.0 on right now (had it on for a few days) and I haven't tried burning a cd yet.

Praetorian 06-13-2002 11:27 PM

^bump^

neo77777 06-14-2002 10:34 AM

mdah, and my CD-burner went to a trash can, pitty.

ngomong 06-15-2002 04:14 PM

I swapped in a new SCSI card (which a friend had) and a new burner, and all worked fine. So, I'm not sure which was causing the problems.

I've been switching back to the old SCSI card (because I needed it's bootable-CD capabilities), and it's been fine reading loads of data from it. I'll try burning with it again, and see what happens.

Praetorian 06-15-2002 04:39 PM

If I still get problems I'm going to change back to my Initio card. I'll reply to this once I get some cds and do a burn...


All times are GMT -5. The time now is 12:36 PM.