Scanner scsi deskjet 6200C used to work nicely on either debian i386 or amd64 on two different computers. Now, with both, same error messages. On the 32 bit machine:
francesco@machinename:/dev$ lsscsi
[0:0:0:0] disk IBM DDRS-34560 S97B /dev/sdc
[0:0:2:0] process HP C6270A 3828 -
[0:0:4:0] cd/dvd MATSHITA CD-R CW-7502 4.16 /dev/sr1
[1:0:0:0] disk ATA Maxtor 6Y080L0 YAR4 /dev/sda
[1:0:1:0] disk ATA ST380215A 3.AA /dev/sdb
[2:0:0:0] cd/dvd HL-DT-ST DVD-RAM GH22NP20 1.04 /dev/sr0
francesco@machinename:/dev$
francesco@machinename:/dev$ dmesg |grep -i scsi
[ 0.738791] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.858761] SCSI subsystem initialized
[ 1.903764] ahc_pci:2:5:0: Host Adapter Bios disabled. Using default SCSI device parameters
[ 1.956476] scsi1 : ata_piix
[ 1.956741] scsi2 : ata_piix
[ 2.265797] scsi 1:0:0:0: Direct-Access ATA Maxtor 6Y080L0 YAR4 PQ: 0 ANSI: 5
[ 2.266390] scsi 1:0:1:0: Direct-Access ATA ST380215A 3.AA PQ: 0 ANSI: 5
[ 2.267928] scsi 2:0:0:0: CD-ROM HL-DT-ST DVD-RAM GH22NP20 1.04 PQ: 0 ANSI: 5
[ 2.311794] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 2.312520] sr 2:0:0:0: Attached scsi CD-ROM sr0
[ 2.347406] sd 1:0:0:0: [sda] Attached SCSI disk
[ 2.347437] sd 1:0:1:0: [sdb] Attached SCSI disk
[ 16.940041] scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
[ 16.940044] <Adaptec 2902/04/10/15/20C/30C SCSI adapter>
[ 16.940046] aic7850: Single Channel A, SCSI Id=7, 3/253 SCBs
[ 16.952426] scsi 0:0:0:0: Direct-Access IBM DDRS-34560 S97B PQ: 0 ANSI: 2
[ 16.952440] scsi0:A:0:0: Tagged Queuing enabled. Depth 8
[ 16.952457] scsi target0:0:0: Beginning Domain Validation
[ 16.968402] scsi target0:0:0: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15)
[ 16.980040] scsi target0:0:0: Domain Validation skipping write tests
[ 16.980044] scsi target0:0:0: Ending Domain Validation
[ 17.259179] scsi 0:0:2:0: Processor HP C6270A 3828 PQ: 0 ANSI: 2
[ 17.259211] scsi target0:0:2: Beginning Domain Validation
[ 17.267378] scsi target0:0:2: Ending Domain Validation
[ 17.537704] scsi 0:0:4:0: CD-ROM MATSHITA CD-R CW-7502 4.16 PQ: 0 ANSI: 2
[ 17.537735] scsi target0:0:4: Beginning Domain Validation
[ 17.545039] scsi target0:0:4: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 8)
[ 17.549555] scsi target0:0:4: Domain Validation skipping write tests
[ 17.549561] scsi target0:0:4: Ending Domain Validation
[ 18.086191] sr1: scsi3-mmc drive: 8x/8x writer xa/form2 cdda tray
[ 18.086384] sr 0:0:4:0: Attached scsi CD-ROM sr1
[ 18.449127] sd 0:0:0:0: [sdc] Attached SCSI disk
francesco@machinename:/dev$
i.e., there is the process, the scanner chip is detected, while the scanner is not attached. No "sg" on /dev.
I have changed the scsi cable with same results. I tried also as superuser with same results. The scanner lamp is lighted.
There is a usb port on the scanner although it must be an obsolete version, it never worked.
Thanks for advice
chiendarret
