LinuxQuestions.org
Did you know LQ has a Linux Hardware Compatibility List?
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Hardware
User Name
Password
Linux - Hardware This forum is for Hardware issues.
Having trouble installing a piece of hardware? Want to know if that peripheral is compatible with Linux?

Notices

Reply
 
Search this Thread
Old 12-20-2003, 05:37 AM   #1
patr
LQ Newbie
 
Registered: Dec 2003
Posts: 3

Rep: Reputation: 0
boot to PATA raid0 on Promise 378 *and see* SATA raid0 ICH5 ?


Hi,

Does PATA raid0 work on 378 for 2.6.x

*or*

Does SATA raid0 work on ICH5 for 2.4.x /w enhanced mode (so I can still see the 378)


I have an ASUS P4C800-E Deluxe, and I want to do the following (please, no flames re: "fake raid" and "Promise is on the PCI bus dont use it" etc.etc.):

BIOS in 'enhanced mode'

ICH5 controller: 2 80GB SATA drives in raid0: boot drive /w XP

Promise 378 controller: 2 40GB PATA drives (on one cable/connector yes I know it is lame): wanna be linux drive

On-board generic IDE controller 1: 1 DVD-RW

On-board generic IDE controller 2: 1 CD-RW

The thing boots and runs in XP just fine.

I am wondering what I can do to make this thing boot properly. I will use any kernel at this point.

When I build a 2.4.x kernel, and build the Promise module (from Promise, with the 'un-GPL' .o), and insmod it, I can see the promise PATA raid. But these kernels dont like the ICH5 driver (which makes the kernel hang - see below).

When I build a 2.6.x kernel, with the built-in 378 support, it only seems to find SATA raid sets ? (I did not verify this, but it certainly does not see my PATA raid set). So it doesn't see the PATA raid set. So no go.

The problem with sticking with 2.4.x kernels is that their ICH5 support, when I load it, it hangs after printing that it has found the ICH5 drives, the kernel hangs (this is tried with 2.4.23, 2.4.22, 2.4.22-ac4). So I never get to the point where I can load the promise module. I tried loading ICH5 last, i.e. all as modules loading 378 first, but it still hangs in the drive detection. If I run in 'non-enhanced BIOS mode', then the ICH5 detection works fine *but* I then cannot see anything off of the 378.

The problem with the 2.6.x kernels is that they dont see the PATA raid on the 378.

Is there any kernel combo I can use to get both to be seen in Linux ? I can also load the Promise 378 in non-raid using their drivers, but they only seem to work on 2.4.x which still has the ICH5 problem. So it is not raid0 specific with the 378 drivers.

The question is really:

Does PATA raid0 work on 378 for 2.6.x

*or*

Does SATA raid0 work on ICH5 for 2.4.x /w enhanced mode (so I can still see the 378)

-patr

Last edited by patr; 12-22-2003 at 12:58 AM.
 
Old 12-22-2003, 12:58 AM   #2
patr
LQ Newbie
 
Registered: Dec 2003
Posts: 3

Original Poster
Rep: Reputation: 0
bump anyone have either working ? Is this a FAQ and so no one is answering ?
 
Old 02-25-2004, 01:36 AM   #3
Minime80
LQ Newbie
 
Registered: Feb 2004
Location: Portland, OR
Distribution: Debian
Posts: 3

Rep: Reputation: 0
Yep, unless I'm missing something. I've got the 2.6.3 kernel and there's a promise driver built in. Shouldn't be too hard setting up an array after that using mdadm. Let me know if you've got any other questions. I know it's kinda hard to get help on raid since they're pretty new for most people.

The only problem you'll have is that linux won't be able to see the windows array since windows and linux set up raid's in completely different ways. Windows will just put the entire array in the partition table of the first disk in the array. Linux actually uses software that treats each disk separately and then combines them.

I've been trying for days now to get a dual boot XP/Debian system to boot off of the ich5r, but because of this difference in how the raid's get setup, I'm not having much luck. For now I've settled on having XP on the ich5r and putting Linux on the promise.
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Promise 376/378 pata Drives with SuSE 10.0 atarianer Linux - Hardware 0 10-20-2005 02:02 AM
sata raid0 dual boot with winxp Sneakeh Linux - Newbie 1 10-27-2004 04:08 PM
Highpoint Raid0 VS Promise Raid1 MaDDeePee Linux - Hardware 7 08-22-2004 10:23 PM
ICH5 in RAID0-Mode under 2.6.x - Striping Problems... colo Linux - Hardware 6 04-10-2004 02:08 PM
System won't boot after installing red hat on raid0 SATA alf550 Red Hat 0 02-09-2004 04:50 AM


All times are GMT -5. The time now is 03:22 PM.

Main Menu
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
identi.ca: @linuxquestions
Facebook: linuxquestions Google+: linuxquestions
Open Source Consulting | Domain Registration