LinuxQuestions.org
Review your favorite Linux distribution.
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - General
User Name
Password
Linux - General This Linux forum is for general Linux questions and discussion.
If it is Linux Related and doesn't seem to fit in any other forum then this is the place.

Notices



Reply
 
Search this Thread
Old 01-08-2005, 03:22 AM   #1
zparihar
Member
 
Registered: Sep 2004
Distribution: Fedora, Debian
Posts: 59

Rep: Reputation: 15
Setup HP PSC 1315 / 1310 - Scanner


Since its fairly simple to setup the Printing side of the HP PSC 1315 / 1310, i'm gonna explain how i did the scanner. (took me a month to figure out. - i ended up finding the documentation and it was dead simple)

Just to clear up - the hp psc 1315 is the same as 1310 - USE THE VALUE 1310
NOT 1315

How to Install HP PSC 1315 All-In-One

***Scanner***

make sure the hp psc 1315 is plugged in.

#1 Make sure you have the following installed:

libsane-hpoj-0.91-9
hpoj-0.91-9
hpijs-1.6-2

#2 on a terminal, type 'ptal-init setup', and answer the questions (its short and
straightforward)

#3 now you wanna type 'ptal-init start' to start the scanner

#4 to test the scanner type in scanimage -d hpoj:mlc:usb:psc_1310_series_ --test

(if you don't have the 1315/1310 replace it that line with the device name:
scanimage -d hpoj:device --test

to find out the name of your device type 'scanimage --list-devices' and replace
the device name in the previous command to test it...

#5 now startup a scanning program like xsane or kooka :

For Kooka -
kooka -d hpoj:mlc:usb:psc_1310_series_

For Xsane -
xsane hpoj:mlc:usb:psc_1310_series_

THATS IT!!


you'll probably want to make sure 'ptal-init start' gets started each time the computer reboots.
Put it in a startup script or something...

Hoped this helped...
Zubin
zparihar@yahoo.com

Last edited by zparihar; 01-08-2005 at 03:24 AM.
 
Old 01-08-2005, 01:06 PM   #2
Beck24
LQ Newbie
 
Registered: Jan 2005
Distribution: Suse 9.1
Posts: 17

Rep: Reputation: 0
Thanx zparihar,

I have a psc 1210 that prints fine but I can't get it to scan, I'll try that only using the 1200 series. Hopefully that will work.
 
Old 01-09-2005, 09:29 PM   #3
zparihar
Member
 
Registered: Sep 2004
Distribution: Fedora, Debian
Posts: 59

Original Poster
Rep: Reputation: 15
Let me know if it works or not...

Let me know if it works or not...
 
Old 01-12-2005, 04:28 PM   #4
Beck24
LQ Newbie
 
Registered: Jan 2005
Distribution: Suse 9.1
Posts: 17

Rep: Reputation: 0
So far it hasn't worked but that's because I can't seem to install hpoj and hpijs. They keep complaining about dependencies, when I have them installed.
I'll let you know when I get them resolved
 
Old 01-13-2005, 02:10 AM   #5
zparihar
Member
 
Registered: Sep 2004
Distribution: Fedora, Debian
Posts: 59

Original Poster
Rep: Reputation: 15
source installation?

have you thought about installing from source?

doesn't suse 9.1 Pro have a package manager where you can install it through yast?
 
Old 01-26-2005, 12:52 AM   #6
kapat
LQ Newbie
 
Registered: Jan 2005
Location: Columbus
Distribution: Debian-Unstable
Posts: 6

Rep: Reputation: 0
thanks zubin

zubin thanks for your details.. I just bought a HP PSC 1315, and got it to work. Btw, I had installed the hplip and hplip_data which was giving me a HP frontend for the printer and scanner. But when I installed hpoj, it removed these two packages ( I was hesitant in the begining, but thought of giving it a try). And thankfully it worked. I was able to get my scanner working. Why are these two incompatible ?

Secondly, I suppose this printer has a max resolution of 1200 dpi, but all of the scanning options offer a max of 600dpi. Why is that ?

kapat
 
Old 01-27-2005, 02:17 AM   #7
zparihar
Member
 
Registered: Sep 2004
Distribution: Fedora, Debian
Posts: 59

Original Poster
Rep: Reputation: 15
I've got to check it out

Hey kapat,

I've actually i've been wondering about that too....

I just haven't had the time to look into it...but then again 600 DPI is not that bad...

I'll try find out when i've got time and let you know...


Zubin Parihar
 
Old 01-27-2005, 09:27 AM   #8
sporks
Member
 
Registered: Dec 2004
Location: Indonesia
Distribution: Slackware
Posts: 211

Rep: Reputation: 30
Re: thanks zubin

Quote:
Originally posted by kapat
zubin thanks for your details.. I just bought a HP PSC 1315, and got it to work. Btw, I had installed the hplip and hplip_data which was giving me a HP frontend for the printer and scanner. But when I installed hpoj, it removed these two packages ( I was hesitant in the begining, but thought of giving it a try). And thankfully it worked. I was able to get my scanner working. Why are these two incompatible ?

Secondly, I suppose this printer has a max resolution of 1200 dpi, but all of the scanning options offer a max of 600dpi. Why is that ?

kapat
hplip is the replacement for hpoj/hpijs as I understand it.
One stop shopping rather than two different files.

I've used it for my PSC750.

Your scanner didn't work with the hplip?

According to this, http://hpinkjet.sourceforge.net/productsmf.php , the 1310 is supported by hplip.
 
Old 01-30-2005, 03:24 PM   #9
kapat
LQ Newbie
 
Registered: Jan 2005
Location: Columbus
Distribution: Debian-Unstable
Posts: 6

Rep: Reputation: 0
hey sparky,
i had followed the instructions on the link u r refering to. before that i had installed, hpijs. then hplip. and yes the scanner was not recognised !! i'll give it another shot, removing hpij and hpoj, as u say, if hplip is hpij+hpoj then it shoukd work. i'll let u kow what turns up..

thanks guys...
 
Old 01-30-2005, 10:06 PM   #10
kapat
LQ Newbie
 
Registered: Jan 2005
Location: Columbus
Distribution: Debian-Unstable
Posts: 6

Rep: Reputation: 0
Okay Sparky, here are my findings, after i removed hpoj, hpijs and installed hpijs, hplip.
1. hplip depends on sane for recognising the scanner. (lol !)
2. sane does not recognise, hp's PSC devices !! here is the link..
http://www.sane-project.org/lists/sa...al.html#S-HPOJ

3. sane-find-scanner gives the following output...

~$ sane-find-scanner

# sane-find-scanner will now attempt to detect your scanner. If the
# result is different from what you expected, first make sure your
# scanner is powered up and properly connected to your computer.

# No SCSI scanners found. If you expected something different, make sure that
# you have loaded a SCSI driver for your SCSI adapter.

found USB scanner (vendor=0x03f0, product=0x3f11) at libusb:001:003
# Your USB scanner was (probably) detected. It may or may not be supported by
# SANE. Try scanimage -L and read the backend's manpage.

# Not checking for parallel port scanners.

# Most Scanners connected to the parallel port or other proprietary ports
# can't be detected by this program.

# You may want to run this program as root to find all devices. Once you
# found the scanner devices, be sure to adjust access permissions as
# necessary.

4. But, hp's page http://hpinkjet.sourceforge.net/productsmf.php says it gives a FULL support !!! Boy, let it support first !

btw, when u start hplip toolbox, and then configure it, what frontend do u use for scanning ?

any more lights ?
 
Old 01-30-2005, 10:14 PM   #11
sporks
Member
 
Registered: Dec 2004
Location: Indonesia
Distribution: Slackware
Posts: 211

Rep: Reputation: 30
I just use Kooka for scanning.

I know I have sane installed.

Never thought abou it much.

Last edited by sporks; 01-30-2005 at 10:18 PM.
 
Old 01-31-2005, 12:31 AM   #12
zparihar
Member
 
Registered: Sep 2004
Distribution: Fedora, Debian
Posts: 59

Original Poster
Rep: Reputation: 15
Scroll up

Scroll up to my original posting...

It should work...its dead simple!


Zubin Parihar
 
Old 01-31-2005, 12:56 AM   #13
kapat
LQ Newbie
 
Registered: Jan 2005
Location: Columbus
Distribution: Debian-Unstable
Posts: 6

Rep: Reputation: 0
zubin, i kow it works and IS simple. thanx 4 ur original posting.
i was just curious to retry hplip. i'll go back and get rid of hplip.
the hpoj project seems to have met a dead end.. just look at this..
http://hpoj.sourceforge.net/news.shtm ????
 
Old 01-31-2005, 09:40 AM   #14
sporks
Member
 
Registered: Dec 2004
Location: Indonesia
Distribution: Slackware
Posts: 211

Rep: Reputation: 30
Quote:
Originally posted by kapat
zubin, i kow it works and IS simple. thanx 4 ur original posting.
i was just curious to retry hplip. i'll go back and get rid of hplip.
the hpoj project seems to have met a dead end.. just look at this..
http://hpoj.sourceforge.net/news.shtm ????
Because it's been replaced by hplip.

I know it works.

I've used it.

Follow these instructions here:
http://hpinkjet.sourceforge.net/install.php#HPLIP

It's dead simple.

I had to edit my Slackware init scripts to start hplip not hpoj other than that it functions no diffently and is supported unlike hpoj it would seem.

Last edited by sporks; 01-31-2005 at 09:46 AM.
 
Old 02-05-2005, 10:51 PM   #15
bernie
LQ Newbie
 
Registered: Jun 2003
Distribution: potato
Posts: 1

Rep: Reputation: 0
pls give me the directions installing hp psc 1315 all in one series

my scanner doesnt work but hte hp psc 1315 is properly installed.will you please give me some reasons why my scanner doesnt work and will you please give me the directions how can i use my scanner..thank you..
 
  


Reply

Tags
post


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
[SOLVED] HP PSC 1315 - Printer detected under CUPs but not working (hplip/hpijs driver) vharishankar Linux - Hardware 19 09-01-2009 03:26 PM
HP PSC 1317 / 1310 - Scanner gbowden Linux - General 1 11-13-2005 10:27 AM
HP PSC 1310/Mdk9.1 - no errors but will not print vasudevadas Linux - Hardware 5 06-22-2005 02:05 PM
Cups configuration, hp psc 1315 printer ArchArael Linux - Hardware 0 05-13-2005 05:18 AM
HP psc 1315 freezes in Slackware fader Slackware 0 10-15-2004 12:43 PM


All times are GMT -5. The time now is 01:46 AM.

Main Menu
Advertisement
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
identi.ca: @linuxquestions
Facebook: linuxquestions Google+: linuxquestions
Open Source Consulting | Domain Registration