Hello Dude
I have some issues with my linux server in Past 2 weeks.Our ftp server is not able to telnet/direct access.So i need to hard reset on the machine...
Below is my dmesg and it looks fine.I am not sure where to start checking...Please advise...
----------------
Some error message from from /var/log/messages
Aug 14 02:07:49 oldftpserv CROND[25909]: (root) CMD (sync;sync;sync;sync)
Aug 14 10:42:56 oldftpserv syslogd 1.4.1: restart.
Aug 14 10:42:25 oldftpserv modprobe: modprobe: Can't locate module block-major-43
Aug 14 10:43:00 oldftpserv kernel: Inode cache hash table entries: 131072 (order: 8, 1048576 bytes)
----------------
[root@oldftpserv log]# dmesg
40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
CPU0: Intel(R) Xeon(TM) CPU 2.80GHz stepping 09
per-CPU timeslice cutoff: 1462.97 usecs.
task migration cache decay timeout: 10 msecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000040
ESR value after enabling vector: 00000000
Booting processor 1/1 eip 2000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 5557.45 BogoMIPS
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
ACPI tables and CPU MSR values mismatch about cpu number
CPU: Physical Processor ID: 3
Intel machine check reporting enabled on CPU#1.
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
CPU1: Intel(R) Xeon(TM) CPU 2.80GHz stepping 09
Booting processor 2/6 eip 2000
Initializing CPU#2
masked ExtINT on CPU#2
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 5557.45 BogoMIPS
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Intel machine check reporting enabled on CPU#2.
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
CPU2: Intel(R) Xeon(TM) CPU 2.80GHz stepping 09
Booting processor 3/7 eip 2000
Initializing CPU#3
masked ExtINT on CPU#3
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 5557.45 BogoMIPS
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 3
Intel machine check reporting enabled on CPU#3.
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
CPU3: Intel(R) Xeon(TM) CPU 2.80GHz stepping 09
Total of 4 processors activated (22229.81 BogoMIPS).
ENABLING IO-APIC IRQs
Setting 8 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 8 ... ok.
Setting 9 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 9 ... ok.
Setting 10 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 10 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 8-0, 8-7, 8-10, 8-11, 8-13, 10-0, 10-1, 10-2, 10-3, 10-4, 10-5, 10-6, 10-7, 10-8, 10-9, 10-10, 10-11, 10-12, 10-13, 10-14, 10-15 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...
..... (found pin 0) ...works.
number of MP IRQ sources: 33.
number of IO-APIC #8 registers: 16.
number of IO-APIC #9 registers: 16.
number of IO-APIC #10 registers: 16.
testing the IO APIC.......................
IO APIC #8......
.... register #00: 08000000
....... : physical APIC id: 08
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 000F0011
....... : max redirection entries: 000F
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 08000000
....... : arbitration: 08
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 00F 0F 0 0 0 0 0 1 1 31
01 00F 0F 0 0 0 0 0 1 1 39
02 000 00 1 0 0 0 0 0 0 00
03 00F 0F 0 0 0 0 0 1 1 41
04 00F 0F 0 0 0 0 0 1 1 49
05 00F 0F 1 1 0 1 0 1 1 51
06 00F 0F 0 0 0 0 0 1 1 59
07 000 00 1 0 0 0 0 0 0 00
08 00F 0F 0 0 0 0 0 1 1 61
09 00F 0F 0 0 0 0 0 1 1 69
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 00F 0F 0 0 0 0 0 1 1 71
0d 000 00 1 0 0 0 0 0 0 00
0e 00F 0F 0 0 0 0 0 1 1 79
0f 00F 0F 0 0 0 0 0 1 1 81
IO APIC #9......
.... register #00: 09000000
....... : physical APIC id: 09
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 000F0011
....... : max redirection entries: 000F
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 09000000
....... : arbitration: 09
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 00F 0F 1 1 0 1 0 1 1 89
01 00F 0F 1 1 0 1 0 1 1 91
02 00F 0F 1 1 0 1 0 1 1 99
03 00F 0F 1 1 0 1 0 1 1 A1
04 00F 0F 1 1 0 1 0 1 1 A9
05 00F 0F 1 1 0 1 0 1 1 B1
06 00F 0F 1 1 0 1 0 1 1 B9
07 00F 0F 1 1 0 1 0 1 1 C1
08 00F 0F 1 1 0 1 0 1 1 C9
09 00F 0F 1 1 0 1 0 1 1 D1
0a 00F 0F 1 1 0 1 0 1 1 D9
0b 00F 0F 1 1 0 1 0 1 1 E1
0c 00F 0F 1 1 0 1 0 1 1 E9
0d 00F 0F 1 1 0 1 0 1 1 32
0e 00F 0F 1 1 0 1 0 1 1 3A
0f 00F 0F 1 1 0 1 0 1 1 42
IO APIC #10......
.... register #00: 0A000000
....... : physical APIC id: 0A
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 000F0011
....... : max redirection entries: 000F
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 0A000000
....... : arbitration: 0A
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 000 00 1 0 0 0 0 0 0 00
02 000 00 1 0 0 0 0 0 0 00
03 000 00 1 0 0 0 0 0 0 00
04 000 00 1 0 0 0 0 0 0 00
05 000 00 1 0 0 0 0 0 0 00
06 000 00 1 0 0 0 0 0 0 00
07 000 00 1 0 0 0 0 0 0 00
08 000 00 1 0 0 0 0 0 0 00
09 000 00 1 0 0 0 0 0 0 00
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 000 00 1 0 0 0 0 0 0 00
0d 000 00 1 0 0 0 0 0 0 00
0e 000 00 1 0 0 0 0 0 0 00
0f 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:0
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ12 -> 0:12
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 1:0
IRQ17 -> 1:1
IRQ18 -> 1:2
IRQ19 -> 1:3
IRQ20 -> 1:4
IRQ21 -> 1:5
IRQ22 -> 1:6
IRQ23 -> 1:7
IRQ24 -> 1:8
IRQ25 -> 1:9
IRQ26 -> 1:10
IRQ27 -> 1:11
IRQ28 -> 1:12
IRQ29 -> 1:13
IRQ30 -> 1:14
IRQ31 -> 1:15
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2783.9349 MHz.
..... host bus clock speed is 132.5681 MHz.
cpu: 0, clocks: 1325681, slice: 265136
CPU0<T0:1325680,T1:1060544,D:0,S:265136,C:1325681>
cpu: 1, clocks: 1325681, slice: 265136
cpu: 2, clocks: 1325681, slice: 265136
cpu: 3, clocks: 1325681, slice: 265136
CPU1<T0:1325680,T1:795408,D:0,S:265136,C:1325681>
CPU2<T0:1325680,T1:530272,D:0,S:265136,C:1325681>
CPU3<T0:1325680,T1:265136,D:0,S:265136,C:1325681>
cpu_sibling_map[0] = 2
cpu_sibling_map[1] = 3
cpu_sibling_map[2] = 0
cpu_sibling_map[3] = 1
mapping CPU#0's runqueue to CPU#2's runqueue.
mapping CPU#1's runqueue to CPU#3's runqueue.
zapping low mappings.
Process timing init...done.
Starting migration thread for cpu 0
Starting migration thread for cpu 1
Starting migration thread for cpu 2
Starting migration thread for cpu 3
PCI: PCI BIOS revision 2.10 entry at 0xfc91e, last bus=5
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Ignoring BAR0-3 of IDE controller 00:0f.1
PCI: Discovered primary peer bus 01 [IRQ]
PCI: Discovered primary peer bus 02 [IRQ]
PCI: Discovered primary peer bus 03 [IRQ]
PCI: Discovered primary peer bus 04 [IRQ]
PCI: Using IRQ router ServerWorks [1166/0201] at 00:0f.0
PCI->APIC IRQ transform: (B0,I4,P0) -> 19
PCI->APIC IRQ transform: (B0,I4,P1) -> 23
PCI->APIC IRQ transform: (B0,I4,P2) -> 27
PCI->APIC IRQ transform: (B3,I6,P0) -> 28
PCI->APIC IRQ transform: (B3,I8,P0) -> 29
PCI->APIC IRQ transform: (B4,I8,P0) -> 30
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS not found.
Total HugeTLB memory allocated, 0
Starting kswapd
allocated 32 pages and 32 bhs reserved for the highmem bounces
VFS: Disk quotas vdquot_6.5.1
aio_setup: num_physpages = 131064
aio_setup: sizeof(struct page) = 60
Hugetlbfs mounted.
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS0 at 0x03f8 (irq = 4) is a 16550A
ttyS1 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 256 RAM disks of 8192K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SvrWks CSB5: IDE controller at PCI slot 00:0f.1
SvrWks CSB5: chipset revision 147
SvrWks CSB5: not 100% native mode: will probe irqs later
SvrWks CSB5: simplex device: DMA forced
ide0: BM-DMA at 0x08b0-0x08b7, BIOS settings: hda
MA, hdb
io
SvrWks CSB5: simplex device: DMA forced
ide1: BM-DMA at 0x08b8-0x08bf, BIOS settings: hdc
MA, hdd
MA
hda: SAMSUNG CD-ROM SN-124, ATAPI CD/DVD-ROM drive
hda: Disabling (U)DMA for SAMSUNG CD-ROM SN-124
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide-floppy driver 0.99.newide
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 16384 buckets, 128Kbytes
TCP: Hash tables configured (established 524288 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
Initializing IPsec netlink socket
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 512k freed
VFS: Mounted root (ext2 filesystem).
SCSI subsystem driver Revision: 1.00
Red Hat/Adaptec aacraid driver (1.1.2 Oct 3 2003 18:09:55)
AAC0: kernel 2.8.4 build 6082
AAC0: monitor 2.8.4 build 6082
AAC0: bios 2.8.0 build 6082
AAC0: serial 9da438d3fafaf001
scsi0 : percraid
Starting timer : 0 0
blk: queue f756ce18, I/O limit 4095Mb (mask 0xffffffff)
Vendor: DELL Model: PERCRAID Mirror Rev: V1.0
Type: Direct-Access ANSI SCSI revision: 02
Starting timer : 0 0
blk: queue f756cc18, I/O limit 4095Mb (mask 0xffffffff)
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 35544576 512-byte hdwr sectors (18199 MB)
sda: Write Protect is off
Partition check:
sda: sda1 sda2 sda3
LVM version 1.0.5+(22/07/2002) module loaded
Journalled Block Device driver loaded
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 224k freed
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xf88b9000, IRQ 5
usb-ohci.c: usb-00:0f.2, ServerWorks OSB4/CSB5 OHCI USB Controller
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 4 ports detected
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
EXT3 FS 2.4-0.9.19, 19 August 2002 on lvm(58,0), internal journal
loop: loaded (max 8 devices)
Adding Swap: 2096472k swap-space (priority -1)
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on lvm(58,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on lvm(58,2), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on lvm(58,3), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on lvm(58,4), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on lvm(58,5), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on lvm(58,6), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on lvm(58,7), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
inserting floppy driver for 2.4.21-4.ELsmp
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
tg3.c:v2.2 (August 24, 2003)
divert: allocating divert_blk for eth0
eth0: Tigon3 [partno(BCM95703A30) rev 1002 PHY(5703)] (PCIX:133MHz:64-bit) 10/100/1000BaseT Ethernet 00:0d:56:b8:33:58
divert: allocating divert_blk for eth1
eth1: Tigon3 [partno(BCM95703A30) rev 1002 PHY(5703)] (PCIX:133MHz:64-bit) 10/100/1000BaseT Ethernet 00:0d:56:b8:33:59
divert: freeing divert_blk for eth0
divert: freeing divert_blk for eth1
ip_tables: (C) 2000-2002 Netfilter core team
tg3.c:v2.2 (August 24, 2003)
divert: allocating divert_blk for eth0
eth0: Tigon3 [partno(BCM95703A30) rev 1002 PHY(5703)] (PCIX:133MHz:64-bit) 10/100/1000BaseT Ethernet 00:0d:56:b8:33:58
divert: allocating divert_blk for eth1
eth1: Tigon3 [partno(BCM95703A30) rev 1002 PHY(5703)] (PCIX:133MHz:64-bit) 10/100/1000BaseT Ethernet 00:0d:56:b8:33:59
ip_tables: (C) 2000-2002 Netfilter core team
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is off for TX and off for RX.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on lvm(58,8), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
lp: driver loaded but no devices found
usb.c: registered new driver serial
usbserial.c: USB Serial support registered for Generic
usbserial.c: USB Serial Driver core v1.4
mtrr: type mismatch for fd000000,800000 old: uncachable new: write-combining
mtrr: type mismatch for fd000000,800000 old: uncachable new: write-combining
aacraid:Battery charge is now OK
