LinuxQuestions.org
Support LQ: Use code LQ3 and save $3 on Domain Registration
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Hardware > Linux - Embedded & Single-board computer
User Name
Password
Linux - Embedded & Single-board computer This forum is for the discussion of Linux on both embedded devices and single-board computers (such as the Raspberry Pi, BeagleBoard and PandaBoard). Discussions involving Arduino, plug computers and other micro-controller like devices are also welcome.

Notices

Reply
 
Search this Thread
Old 07-22-2008, 12:40 AM   #1
ts7300
LQ Newbie
 
Registered: Feb 2008
Posts: 17

Rep: Reputation: 0
Ts7300 Fpga Uart Problem


Hi,
I am using com3(TS7300)port with modem and in the same manner using
other board with modem and by ATDT dialing the modem and once two
board are connected using buad rate 115200bits/sec then using keyboard
sending data from one board to other but data is not receving on the
Board but instead of using 2 board,when I connected BOARD with
PC(LINUX)using modem then transmitting data from Board its coming on
TERMINAL of PC.But when I transmitting data from PC nothing is coming
on board,its means that board is not receiving data only transmitting
the data through COM3,I am stuck up at this problem.PLS Guide me.

THANX....
 
Old 07-22-2008, 06:33 PM   #2
michaelk
Moderator
 
Registered: Aug 2002
Posts: 11,803

Rep: Reputation: 721Reputation: 721Reputation: 721Reputation: 721Reputation: 721Reputation: 721Reputation: 721
Have you verified the wires on the cable that connects to COM 3 on bad board good?
If so have you tried this test with another COM port on the board?
 
Old 07-23-2008, 12:37 AM   #3
ts7300
LQ Newbie
 
Registered: Feb 2008
Posts: 17

Original Poster
Rep: Reputation: 0
Hi,
I have checked with other com(4,5,6) of board same problem is coming.When I am Transmiting the data from Board tx Data LED(on board) is blinking and When I am Transmiting the data from external device i.e. PC via minicom no data is receiving on board(rx Data led is not blinking) its means only data is Transmiting from FPGA port not receiving at COM port.Why this problem is coming I am not getting.
PLS guide me from coming out this problem.

Thanx.

Last edited by ts7300; 07-23-2008 at 12:38 AM.
 
Old 07-23-2008, 08:50 AM   #4
michaelk
Moderator
 
Registered: Aug 2002
Posts: 11,803

Rep: Reputation: 721Reputation: 721Reputation: 721Reputation: 721Reputation: 721Reputation: 721Reputation: 721
Did you make sure the wiring for the RX signal is good?
 
Old 07-28-2008, 05:23 AM   #5
ts7300
LQ Newbie
 
Registered: Feb 2008
Posts: 17

Original Poster
Rep: Reputation: 0
Now I am facing another problem.
I have connected two embedded board(TS 7300) using two modems.One is DFM-562E++ and other is DFM-560ES. both are 56k modems.Later one is transmitting & receiving both but the first one is able to only receive but not transmitting.
So can u suggest some possible solution to this problem.
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Ts7300 Fpga Uart ts7300 Linux - Embedded & Single-board computer 1 02-08-2008 11:51 PM
help about fpga? omeraygor Linux - Newbie 2 01-15-2008 08:16 AM
Fpga Usb Four Programming 3 12-07-2007 09:52 PM
Problem in interrupt handler for uart 16550 mrinal mishra Linux - Kernel 3 05-05-2006 12:00 AM


All times are GMT -5. The time now is 06:03 AM.

Main Menu
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
identi.ca: @linuxquestions
Facebook: linuxquestions Google+: linuxquestions
Open Source Consulting | Domain Registration