bboting panda board es

3988900 bytes read
## Booting kernel from Legacy Image at 80000000 ...
   Image Name:   Linux-3.0.8-g781c6c6-dirty
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3988836 Bytes = 3.8 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.0.8-g781c6c6-dirty (root@pcb-ee206576) (gcc version 4.4.1 (Sourcery G++ Lite 2010q1-202) ) #1 SMP PREEMPT Fri Aug 17 02:28:08 IST 2012
[    0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387f
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: OMAP4 Panda board
[    0.000000] Truncating RAM at 80000000-bfffffff to -afffffff (vmalloc region overlap).
[    0.000000] Reserving 33554432 bytes SDRAM for VRAM
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] OMAP4460 ES1.1
[    0.000000] SRAM: Mapped pa 0x40300000 to va 0xfe400000 size: 0xd000
[    0.000000] On node 0 totalpages: 169984
[    0.000000] free_area_init_node: node 0, pgdat c07bc080, node_mem_map c0930000
[    0.000000]   Normal zone: 1536 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 168448 pages, LIFO batch:31
[    0.000000] PERCPU: Embedded 7 pages/cpu @c0f3a000 s6912 r8192 d13568 u32768
[    0.000000] pcpu-alloc: s6912 r8192 d13568 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 168448
[    0.000000] Kernel command line: console=ttyO2,115200n8 mem=1G androidboot.console=ttyO2 vram="32M" omapfb.vram=0:16M omapfb.mode=dvi:1024x600MR-16@60 consoleblank0
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 512MB 152MB = 664MB total
[    0.000000] Memory: 663496k/663496k available, 122936k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
[    0.000000]     vmalloc : 0xf0800000 - 0xf8000000   ( 120 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xf0000000   ( 768 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .init : 0xc0008000 - 0xc0046000   ( 248 kB)
[    0.000000]       .text : 0xc0046000 - 0xc075c000   (7256 kB)
[    0.000000]       .data : 0xc075c000 - 0xc07bc860   ( 387 kB)
[    0.000000]        .bss : 0xc07bc884 - 0xc092f958   (1485 kB)
[    0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:410
[    0.000000] omap_hwmod: dpll_mpu_m2_ck: missing clockdomain for dpll_mpu_m2_ck.
[    0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz
[    0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
[    0.000030] Calibrating delay loop... 1830.74 BogoMIPS (lpj=7151616)
[    0.070373] pid_max: default: 32768 minimum: 301
[    0.070373] Mount-cache hash table entries: 512
[    0.070373] Initializing cgroup subsys debug
[    0.071166] Initializing cgroup subsys cpuacct
[    0.071166] Initializing cgroup subsys freezer
[    0.071166] CPU: Testing write buffer coherency: ok
[    0.071624] L310 cache controller enabled
[    0.071655] l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x5e470000, Cache size: 1048576 B
[    0.149780] CPU1: Booted secondary processor
[    0.220123] Brought up 2 CPUs
[    0.220123] SMP: Total of 2 processors activated (3670.89 BogoMIPS).
[    0.220306] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for emif_fw
[    0.222717] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l3_instr
[    0.222717] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l3_main_1
[    0.222717] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l3_main_2
[    0.222747] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_abe
[    0.222747] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_cfg
[    0.222747] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_per
[    0.222778] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_wkup
[    0.222778] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for mpu_private
[    0.222778] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for sl2if
[    0.222869] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for thermal_sensor
[    0.222869] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for usbhs_ohci
[    0.222869] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for usbhs_ehci
[    0.222869] omap_hwmod: l3_div_ck: missing clockdomain for l3_div_ck.
[    0.223571] omap_hwmod: l4_div_ck: missing clockdomain for l4_div_ck.
[    0.227844] omap_hwmod: mcpdm: cannot be enabled (3)
[    0.233154] print_constraints: dummy: 
[    0.233154] NET: Registered protocol family 16
[    0.233489] GPMC revision 6.0
[    0.233489] EMIF0 is enabled with IRQ142
[    0.234497] EMIF1 is enabled with IRQ143
[    0.234497] Last reset was cold reset (PRM_RSTST=0x1)
[    0.234527] 
[    0.234893] OMAP GPIO hardware version 0.1
[    0.235870] omap_mux_init: Add partition: #1: core, flags: 2
[    0.237274] omap_mux_init: Add partition: #2: wkup, flags: 2
[    0.237274] omap_mux_get_by_name: Could not find signal uart1_cts.uart1_cts
[    0.238189] omap_hwmod_mux_init: Could not allocate device mux entry
[    0.248107] OMAP DMA hardware revision 0.0
[    0.248107] omap_rproc_get_pool: carveout memory is unavailable: 0x0, 0x0
[    0.254211] bio: create slab <bio-0> at 0
[    0.254516] print_constraints: vwl1271: 1800 mV 
[    0.254516] i2c-core: driver [twl] using legacy suspend method
[    0.255096] i2c-core: driver [twl] using legacy resume method
[    0.255096] SCSI subsystem initialized
[    0.255096] usbcore: registered new interface driver usbfs
[    0.255096] usbcore: registered new interface driver hub
[    0.255706] usbcore: registered new device driver usb
[    0.256286] omap_i2c omap_i2c.1: bus 1 rev4.0 at 400 kHz
[    0.256835] Skipping twl internal clock init and using bootloader value (unknown osc rate)
[    0.257385] twl6030: PIH (irq 39) chaining IRQs 368..387
[    0.258880] print_constraints: VUSB: 3300 mV normal standby
[    0.461273] twl6030_usb twl6030_usb: Initialized TWL6030 USB module
[    0.461822] print_constraints: VMMC: 1200 <--> 3000 mV at 3000 mV normal standby
[    0.462188] print_constraints: VPP: 1800 <--> 2500 mV at 1900 mV normal standby
[    0.462188] print_constraints: VCXIO: 1800 mV normal standby
[    0.462860] print_constraints: VDAC: 1800 mV normal standby
[    0.463287] print_constraints: VAUX2_6030: 1200 <--> 2800 mV at 1800 mV normal standby
[    0.463623] print_constraints: VAUX3_6030: 1000 <--> 3000 mV at 1200 mV normal standby
[    0.464447] print_constraints: CLK32KG: 
[    0.464477] print_constraints: VANA: 2100 mV normal standby
[    0.464874] omap_i2c omap_i2c.2: bus 2 rev4.0 at 400 kHz
[    0.465087] omap_i2c omap_i2c.3: bus 3 rev4.0 at 100 kHz
[    0.465332] omap_i2c omap_i2c.4: bus 4 rev4.0 at 400 kHz
[    0.465454] omap-rproc omap-rproc.0: dsp is available
[    0.465454] omap-rproc omap-rproc.1: ipu is available
[    0.465454] Advanced Linux Sound Architecture Driver Version 1.0.24.
[    0.466003] Bluetooth: Core ver 2.16
[    0.466003] NET: Registered protocol family 31
[    0.466583] Bluetooth: HCI device and connection manager initialized
[    0.466583] Bluetooth: HCI socket layer initialized
[    0.466613] Bluetooth: L2CAP socket layer initialized
[    0.466613] Bluetooth: SCO socket layer initialized
[    0.466949] cfg80211: Calling CRDA to update world regulatory domain
[    0.467071] Switching to clocksource 32k_counter
[    0.469238] musb-hdrc: version 6.0, musb-dma, peripheral
[    0.469451] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[    0.469451] musb-hdrc: MHDRC RTL version 2.0 
[    0.469482] musb-hdrc: setup fifo_mode 4
[    0.469482] musb-hdrc: 28/31 max ep, 16384/16384 memory
[    0.469482] musb-hdrc musb-hdrc: USB Peripheral mode controller at fc0ab000 using DMA, IRQ 124
[    0.469818] NET: Registered protocol family 2
[    0.470092] Switched to NOHz mode on CPU #0
[    0.470123] Switched to NOHz mode on CPU #1
[    0.470245] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.470245] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.470245] TCP bind hash table entries: 65536 (order: 8, 1572864 bytes)
[    0.470245] TCP: Hash tables configured (established 131072 bind 65536)
[    0.470245] TCP reno registered
[    0.475280] UDP hash table entries: 512 (order: 3, 32768 bytes)
[    0.475372] UDP-Lite hash table entries: 512 (order: 3, 32768 bytes)
[    0.475616] NET: Registered protocol family 1
[    1.233459] omap_init_opp_table: no hwmod or odev for hsi, [22] cannot add OPPs.
[    1.233459] omap_init_opp_table: no hwmod or odev for hsi, [23] cannot add OPPs.
[    1.381866] ram_console: got buffer at a0000000, size 200000
[    1.382751] ram_console: uncorrectable error in header
[    1.382751] ram_console: no valid data in buffer (sig = 0xc28faa0e)
[    1.394073] console [ram-1] enabled
[    1.394073] omap-iommu omap-iommu.0: ducati registered
[    1.394744] omap-iommu omap-iommu.1: tesla registered
[    1.401123] ashmem: initialized
[    1.405792] fuse init (API version 7.16)
[    1.405792] msgmni has been set to 1295
[    1.409393] io scheduler noop registered
[    1.409454] io scheduler deadline registered
[    1.409454] io scheduler cfq registered (default)
[    1.409729] start plist test
[    1.409729] end plist test
[    1.419525] OMAP DSS rev 4.0
[    1.426818] dsscomp: initializing.
[    1.427429] misc dsscomp: display0=hdmi_panel
[    1.427581] misc dsscomp: display1=generic_dpi_panel
[    1.427581] misc dsscomp: found 2 displays and 4 overlays
[    1.428009] could not allocate slot
[    1.428314] omap-rproc omap-rproc.1: powering up ipu
[    1.428527] virtio_rpmsg_bus virtio0: rpmsg backend virtproc probed successfully
[    1.428802] virtio_rpmsg_bus virtio1: rpmsg backend virtproc probed successfully
[    1.429748] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 104) is a OMAP UART0
[    1.459991] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 105) is a OMAP UART1
[    1.499053] omap_uart.2: ttyO2 at MMIO 0x48020000 (irq = 106) is a OMAP UART2
[    2.516571] console [ttyO2] enabled
[    2.624206] omap_uart.3: ttyO3 at MMIO 0x4806e000 (irq = 102) is a OMAP UART3
[    2.779907] omap_ion_probe: adding heap secure_input of type 2 with ba300000@5a00000
[    2.788726] omap_ion_probe: adding heap tiler of type 4 with ada00000@6000000
[    2.796691] omap_ion_probe: adding heap nonsecure_tiler of type 4 with a0200000@2000000
[    2.805572] PVR: PVRCore_Init
[    2.809295] PVR: PVRSRVDriverProbe(pDevice=eb4ad800)
[    2.814910] PVR: SGX register base: 0x56000000
[    2.819885] PVR: SGX register size: 65535
[    2.824432] PVR: SGX IRQ: 53
[    2.824432] PVR: EnableSystemClocks: Enabling System Clocks
[    2.833892] PVR_K:(Warning): EnableSGXClocks: Unable to scale SGX frequency (EBUSY) [167, drivers/gpu/pvr/omap4/sysutils_linux.c]
[    2.846862] PVR_K:(Warning): EnableSGXClocks: Unable to scale SGX frequency (EBUSY) [167, drivers/gpu/pvr/omap4/sysutils_linux.c]
[    2.860046] PVR: PVRCore_Init: major device 251
[    2.870727] brd: module loaded
[    2.874145] loop: module loaded
[    2.882537] PPP generic driver version 2.4.2
[    2.882537] PPP Deflate Compression module registered
[    2.882537] PPP BSD Compression module registered
[    2.900115] PPP MPPE Compression module registered
[    2.905487] NET: Registered protocol family 24
[    2.905487] usbcore: registered new interface driver asix
[    2.918090] usbcore: registered new interface driver cdc_ether
[    2.924621] usbcore: registered new interface driver smsc95xx
[    2.928894] usbcore: registered new interface driver net1080
[    2.936553] usbcore: registered new interface driver cdc_subset
[    2.944122] usbcore: registered new interface driver zaurus
[    2.950317] cdc_ncm: 04-Aug-2011
[    2.954071] usbcore: registered new interface driver cdc_ncm
[    2.959991] usbcore: registered new interface driver zd1201
[    2.960449] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.974121] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[    2.974121] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
[    2.988677] ehci-omap ehci-omap.0: irq 109, io mem 0x4a064c00
[    3.001586] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[    3.007995] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    3.007995] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.023651] usb usb1: Product: OMAP-EHCI Host Controller
[    3.023651] usb usb1: Manufacturer: Linux 3.0.8-g781c6c6-dirty ehci_hcd
[    3.023651] usb usb1: SerialNumber: ehci-omap.0
[    3.042327] hub 1-0:1.0: USB hub found
[    3.046569] hub 1-0:1.0: 3 ports detected
[    3.077209] usbcore: registered new interface driver cdc_acm
[    3.077209] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    3.092498] Initializing USB Mass Storage driver...
[    3.092498] usbcore: registered new interface driver usb-storage
[    3.104705] USB Mass Storage support registered.
[    3.109832] usbcore: registered new interface driver usbserial
[    3.116516] usbserial: USB Serial Driver core
[    3.116516] USB Serial support registered for Keyspan - (without firmware)
[    3.129058] USB Serial support registered for Keyspan 1 port adapter
[    3.129058] USB Serial support registered for Keyspan 2 port adapter
[    3.143188] USB Serial support registered for Keyspan 4 port adapter
[    3.150451] usbcore: registered new interface driver keyspan
[    3.156738] keyspan: v1.1.5:Keyspan USB to Serial Converter Driver
[    3.365386] android_usb gadget: Mass Storage Function, version: 2009/09/11
[    3.372985] android_usb gadget: Number of LUNs=1
[    3.377197] usb 1-1: new high speed USB device number 2 using ehci-omap
[    3.385345]  lun0: LUN: removable file: (no medium)
[    3.390808] android_usb gadget: android_usb ready
[    3.396179] mousedev: PS/2 mouse device common for all mice
[    3.403381] twl_rtc twl_rtc: Power up reset detected.
[    3.409912] twl_rtc twl_rtc: Enabling TWL-RTC.
[    3.416259] using rtc device, twl_rtc, for alarms
[    3.416259] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
[    3.428680] i2c /dev entries driver
[    3.433166] lirc_dev: IR Remote Control driver registered, major 248 
[    3.433166] IR NEC protocol handler initialized
[    3.445251] IR RC5(x) protocol handler initialized
[    3.445251] IR RC6 protocol handler initialized
[    3.455627] IR JVC protocol handler initialized
[    3.455627] IR Sony protocol handler initialized
[    3.465759] IR RC5 (streamzap) protocol handler initialized
[    3.471984] IR LIRC bridge handler initialized
[    3.476928] dmm: probe base: fd300000, irq 145
[    3.484252] OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[    3.492401] device-mapper: uevent: version 1.0.3
[    3.497833] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com
[    3.507202] Bluetooth: HCI UART driver ver 2.2
[    3.512115] Bluetooth: HCI H4 protocol initialized
[    3.517395] cpuidle: using governor ladder
[    3.521881] cpuidle: using governor menu
[    3.531433] usbcore: registered new interface driver usbhid
[    3.537506] usbhid: USB HID core driver
[    3.542083] usb 1-1: New USB device found, idVendor=0424, idProduct=9514
[    3.542205] logger: created 256K log 'log_main'
[    3.542297] logger: created 256K log 'log_events'
[    3.542388] logger: created 256K log 'log_radio'
[    3.542480] logger: created 256K log 'log_system'
[    3.542602] thermal_governor_dev_register:Adding omap_ondie_governor governor
[    3.542877] thermal_sensor_dev_register:Found cpu cpu
[    3.542877] thermal_sensor_dev_register:Adding omap_ondie_sensor sensor
[    3.544921] thermal_sensor_set_temp:No cooling agents for domain cpu
[    3.544921] omap_report_temp:thermal_sensor_set_temp reports error
[    3.554199] thermal_sensor_set_temp:No cooling agents for domain cpu
[    3.554260] thermal_sensor_set_temp:No cooling agents for domain cpu
[    3.554260] omap_report_temp:thermal_sensor_set_temp reports error
[    3.554290] omap_temp_sensor omap_temp_sensor.0: omap_ondie_sensor : 'omap_temp_sensor'
[    3.556610] SDP4430 SoC init
[    3.561279] twl6040-codec twl6040-codec: couldn't get VDDHF regulator -19
[    3.644683] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    3.653106] hub 1-1:1.0: USB hub found
[    3.658294] hub 1-1:1.0: 5 ports detected
[    3.687469] asoc: null-codec-dai <-> MultiMedia1 mapping ok
[    3.694519] asoc: null-codec-dai <-> MultiMedia2 mapping ok
[    3.701782] asoc: null-codec-dai <-> Voice mapping ok
[    3.708221] asoc: null-codec-dai <-> Tones mapping ok
[    3.714630] asoc: null-codec-dai <-> Vibra mapping ok
[    3.720794] asoc: null-codec-dai <-> MODEM mapping ok
[    3.726959] asoc: null-codec-dai <-> MultiMedia1 LP mapping ok
[    3.734558] asoc: FM Digital <-> omap-mcbsp-dai.1 mapping ok
[    3.741790] asoc: twl6040-dl1 <-> mcpdm-dl mapping ok
[    3.748779] asoc: dmic-hifi <-> omap-dmic-dai-0 mapping ok
[    3.756378] twl6040-codec twl6040-codec: ASoC: Failed to create Aux/FM Stereo In debugfs file
[    3.766967] asoc: twl6040-dl1 <-> mcpdm-dl1 mapping ok
[    3.773315] asoc: twl6040-ul <-> mcpdm-ul1 mapping ok
[    3.779602] asoc: twl6040-dl2 <-> mcpdm-dl2 mapping ok
[    3.785980] asoc: twl6040-vib <-> mcpdm-vib mapping ok
[    3.792419] asoc: Bluetooth <-> omap-mcbsp-dai.0 mapping ok
[    3.799377] asoc: Bluetooth <-> omap-mcbsp-dai.0 mapping ok
[    3.806335] asoc: FM Digital <-> omap-mcbsp-dai.1 mapping ok
[    3.813385] asoc: MODEM <-> omap-mcbsp-dai.1 mapping ok
[    3.819915] asoc: dmic-hifi <-> omap-dmic-abe-dai-0 mapping ok
[    3.827087] asoc: dmic-hifi <-> omap-dmic-abe-dai-1 mapping ok
[    3.834228] asoc: dmic-hifi <-> omap-dmic-abe-dai-2 mapping ok
[    3.840759] mmc0: host does not support reading read-only switch. assuming write-enable.
[    3.851470] input: Panda Headset Jack as /devices/platform/soc-audio/sound/card0/input0
[    3.862091] ALSA device list:
[    3.865447]   #0: TI OMAP4 Board
[    3.869232] GACT probability NOT on
[    3.873107] Mirror/redirect action on
[    3.877288] mmc0: new SDHC card at address e624
[    3.882598] u32 classifier
[    3.885620] mmcblk0: mmc0:e624 SD04G 3.69 GiB 
[    3.890594]     Actions configured
[    3.894317] Netfilter messages via NETLINK v0.30.
[    3.900024] nf_conntrack version 0.5.0 (10367 buckets, 41468 max)
[    3.907623] ctnetlink v0.93: registering with nfnetlink.
[    3.913482]  mmcblk0: p1 p2
[    3.921203] xt_time: kernel timezone is -0000
[    3.927734] ip_tables: (C) 2000-2006 Netfilter Core Team
[    3.952301] arp_tables: (C) 2002 David S. Miller
[    3.957458] TCP cubic registered
[    3.961212] usb 1-1.1: new high speed USB device number 3 using ehci-omap
[    3.976226] NET: Registered protocol family 10
[    3.993438] Mobile IPv6
[    3.996124] IPv6 over IPv4 tunneling driver
[    4.011352] NET: Registered protocol family 17
[    4.030334] NET: Registered protocol family 15
[    4.045959] Bluetooth: RFCOMM TTY layer initialized
[    4.051361] Bluetooth: RFCOMM socket layer initialized
[    4.057006] Bluetooth: RFCOMM ver 1.11
[    4.061218] NET: Registered protocol family 35
[    4.068847] lib80211: common routines for IEEE802.11 drivers
[    4.075042] lib80211_crypt: registered algorithm 'NULL'
[    4.080841] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    4.089599] ThumbEE CPU extension supported.
[    4.094329] Registering SWP/SWPB emulation handler

it is stuck here
please throw some idea

What do you expect to see? There doesn't seem to be any root filesystem specified, nor an init process named. Are these defaults built into the kernel? Do you have a root filesystem?

--- rod.