Actually I'm using a amcc taishan ppc440gx,and I want it support my marvell sata and i download the kernel at
ftp://ftp.denx.de/pub/linux/
and compile my kernel for taishan ppc440gx.but It can't boot .....
*****************************************************************************
eth1: found ET1011C Gigabit Ethernet PHY (0x03)
e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
PPP generic driver version 2.4.2
NET: Registered protocol family 24
sata_mv 0000:00:01.0: version 0.81
sata_mv 0000:00:01.0: 32 slots 8 ports SCSI mode IRQ via INTx
scsi0 : sata_mv
scsi1 : sata_mv
scsi2 : sata_mv
scsi3 : sata_mv
scsi4 : sata_mv
scsi5 : sata_mv
scsi6 : sata_mv
scsi7 : sata_mv
ata1: SATA max UDMA/133 cmd 0x00000000 ctl 0xd10a2120 bmdma 0x00000000 irq 23
ata2: SATA max UDMA/133 cmd 0x00000000 ctl 0xd10a4120 bmdma 0x00000000 irq 23
ata3: SATA max UDMA/133 cmd 0x00000000 ctl 0xd10a6120 bmdma 0x00000000 irq 23
ata4: SATA max UDMA/133 cmd 0x00000000 ctl 0xd10a8120 bmdma 0x00000000 irq 23
ata5: SATA max UDMA/133 cmd 0x00000000 ctl 0xd10b2120 bmdma 0x00000000 irq 23
ata6: SATA max UDMA/133 cmd 0x00000000 ctl 0xd10b4120 bmdma 0x00000000 irq 23
ata7: SATA max UDMA/133 cmd 0x00000000 ctl 0xd10b6120 bmdma 0x00000000 irq 23
ata8: SATA max UDMA/133 cmd 0x00000000 ctl 0xd10b8120 bmdma 0x00000000 irq 23
ata1: no device found (phy stat 00000000)
ata2: no device found (phy stat 00000000)
ata3: no device found (phy stat 00000000)
ata4: no device found (phy stat 00000000)
ata5.00: ATA-7: ST380211AS, 3.AAE, max UDMA/133
ata5.00: 156301488 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata5.00: configured for UDMA/133
ata6: no device found (phy stat 00000000)
ata7: no device found (phy stat 00000000)
ata8: no device found (phy stat 00000000)
scsi 4:0:0:0: Direct-Access ATA ST380211AS 3.AA PQ: 0 ANSI: 5
sd 4:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 4:0:0:0: [sda] Write Protect is off
sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 4:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 4:0:0:0: [sda] Write Protect is off
sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda:
****************************************************************
and it stopped here ....
here are some of my config file.
CONFIG_PCI=y
CONFIG_SCSI=y
CONFIG_SCSI_DMA=y
CONFIG_BLK_DEV_SD=y
CONFIG_ATA=y
CONFIG_SATA_MV=y
any ideas?
