LinuxQuestions.org

LinuxQuestions.org (/questions/)
-   Debian (https://www.linuxquestions.org/questions/debian-26/)
-   -   Debian Squeeze - No prompt at boot (https://www.linuxquestions.org/questions/debian-26/debian-squeeze-no-prompt-at-boot-4175438534/)

acastano 11-24-2012 07:38 AM

Debian Squeeze - No prompt at boot
 
Hello,

my debian squeeze has been unplugged by mistake and since this action if I boot it, plugging a usb keyboard and a vga screen I have no prompt to login. If I connect to this server using a ssh connection, I have a prompt and I can log in it with my root user.

I have searched on the internet and I have not found any solution. I have compared my /etc/inittab with an another /etc/inittab from another server and there is no difference.

I am lost, could you give me a clue to keep searching?

Thank you very much.


Here you are my dmesg:

[ 0.000000] NR_IRQS:1280
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2792.712 MHz processor.
[ 0.008005] Calibrating delay loop (skipped), value calculated using timer frequency.. 5585.42 BogoMIPS (lpj=11170848)
[ 0.008027] Security Framework initialized
[ 0.008033] SELinux: Disabled at boot.
[ 0.008044] Mount-cache hash table entries: 512
[ 0.008197] Initializing cgroup subsys ns
[ 0.008204] Initializing cgroup subsys cpuacct
[ 0.008209] Initializing cgroup subsys devices
[ 0.008213] Initializing cgroup subsys freezer
[ 0.008215] Initializing cgroup subsys net_cls
[ 0.008249] CPU: Trace cache: 12K uops, L1 D cache: 16K
[ 0.008253] CPU: L2 cache: 1024K
[ 0.008256] CPU: Physical Processor ID: 0
[ 0.008259] CPU: Processor Core ID: 0
[ 0.008266] mce: CPU supports 4 MCE banks
[ 0.008280] CPU0: Thermal monitoring enabled (TM1)
[ 0.012009] using mwait in idle threads.
[ 0.012019] Performance Events: no PMU driver, software events only.
[ 0.012027] Checking 'hlt' instruction... OK.
[ 0.029630] ACPI: Core revision 20090903
[ 0.037150] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.037557] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.077244] CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 04
[ 0.080001] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.012000] Initializing CPU#1
[ 0.012000] CPU: Trace cache: 12K uops, L1 D cache: 16K
[ 0.012000] CPU: L2 cache: 1024K
[ 0.012000] CPU: Physical Processor ID: 0
[ 0.012000] CPU: Processor Core ID: 0
[ 0.012000] CPU1: Thermal monitoring enabled (TM1)
[ 0.164078] CPU1: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 04
[ 0.164090] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.168106] Brought up 2 CPUs
[ 0.168112] Total of 2 processors activated (11171.89 BogoMIPS).
[ 0.168803] CPU0 attaching sched-domain:
[ 0.168810] domain 0: span 0-1 level SIBLING
[ 0.168814] groups: group c1c0370c cpus 0 (cpu_power = 589) group c1e0370c cpus 1 (cpu_power = 589)
[ 0.168827] domain 1: span 0-1 level MC
[ 0.168830] groups: group c1c03778 cpus 0-1 (cpu_power = 1178)
[ 0.168838] CPU1 attaching sched-domain:
[ 0.168841] domain 0: span 0-1 level SIBLING
[ 0.168845] groups: group c1e0370c cpus 1 (cpu_power = 589) group c1c0370c cpus 0 (cpu_power = 589)
[ 0.168854] domain 1: span 0-1 level MC
[ 0.168857] groups: group c1c03778 cpus 0-1 (cpu_power = 1178)
[ 0.168980] devtmpfs: initialized
[ 0.168980] HP Compaq Laptop series board detected. Selecting BIOS-method for reboots.
[ 0.168980] regulator: core version 0.5
[ 0.168980] NET: Registered protocol family 16
[ 0.168980] ACPI: bus type pci registered
[ 0.168980] PCI: MCFG configuration 0: base d0000000 segment 0 buses 0 - 255
[ 0.168980] PCI: MCFG area at d0000000 reserved in E820
[ 0.168980] PCI: Using MMCONFIG for extended config space
[ 0.168980] PCI: Using configuration type 1 for base access
[ 0.168980] bio: create slab <bio-0> at 0
[ 0.168980] ACPI: EC: Look up EC in DSDT
[ 0.175110] ACPI: Interpreter enabled
[ 0.175118] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.175150] ACPI: Using IOAPIC for interrupt routing
[ 0.181014] ACPI: No dock devices found.
[ 0.181632] ACPI Warning for \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20090903/nspredef-336)
[ 0.181645] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.181760] pci 0000:00:02.0: reg 10 32bit mmio: [0xcfd00000-0xcfd7ffff]
[ 0.181768] pci 0000:00:02.0: reg 14 io port: [0x1800-0x1807]
[ 0.181774] pci 0000:00:02.0: reg 18 32bit mmio pref: [0xe0000000-0xefffffff]
[ 0.181781] pci 0000:00:02.0: reg 1c 32bit mmio: [0xcfd80000-0xcfdbffff]
[ 0.181913] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.181919] pci 0000:00:1c.0: PME# disabled
[ 0.182015] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.182020] pci 0000:00:1c.1: PME# disabled
[ 0.182078] pci 0000:00:1d.0: reg 20 io port: [0x1440-0x145f]
[ 0.182135] pci 0000:00:1d.1: reg 20 io port: [0x1460-0x147f]
[ 0.182193] pci 0000:00:1d.2: reg 20 io port: [0x1480-0x149f]
[ 0.182250] pci 0000:00:1d.3: reg 20 io port: [0x14a0-0x14bf]
[ 0.182312] pci 0000:00:1d.7: reg 10 32bit mmio: [0xcfdc0000-0xcfdc03ff]
[ 0.182382] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.182388] pci 0000:00:1d.7: PME# disabled
[ 0.182486] pci 0000:00:1e.2: reg 10 io port: [0x1000-0x10ff]
[ 0.182494] pci 0000:00:1e.2: reg 14 io port: [0x1400-0x143f]
[ 0.182501] pci 0000:00:1e.2: reg 18 32bit mmio: [0xcfdc0400-0xcfdc05ff]
[ 0.182509] pci 0000:00:1e.2: reg 1c 32bit mmio: [0xcfdc0600-0xcfdc06ff]
[ 0.182548] pci 0000:00:1e.2: PME# supported from D0 D3hot D3cold
[ 0.182553] pci 0000:00:1e.2: PME# disabled
[ 0.182636] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[ 0.182645] pci 0000:00:1f.0: quirk: region f800-f87f claimed by ICH6 ACPI/GPIO/TCO
[ 0.182652] pci 0000:00:1f.0: quirk: region fa00-fa3f claimed by ICH6 GPIO
[ 0.182657] pci 0000:00:1f.0: LPC Generic IO decode 1 PIO at 0400-047f
[ 0.182662] pci 0000:00:1f.0: LPC Generic IO decode 2 PIO at 0480-048f
[ 0.182693] pci 0000:00:1f.1: reg 10 io port: [0x1808-0x180f]
[ 0.182701] pci 0000:00:1f.1: reg 14 io port: [0x1828-0x182b]
[ 0.182709] pci 0000:00:1f.1: reg 18 io port: [0x1810-0x1817]
[ 0.182717] pci 0000:00:1f.1: reg 1c io port: [0x182c-0x182f]
[ 0.182725] pci 0000:00:1f.1: reg 20 io port: [0x14e0-0x14ef]
[ 0.182774] pci 0000:00:1f.2: reg 10 io port: [0x1818-0x181f]
[ 0.182781] pci 0000:00:1f.2: reg 14 io port: [0x1830-0x1833]
[ 0.182789] pci 0000:00:1f.2: reg 18 io port: [0x1820-0x1827]
[ 0.182796] pci 0000:00:1f.2: reg 1c io port: [0x1834-0x1837]
[ 0.182804] pci 0000:00:1f.2: reg 20 io port: [0x14f0-0x14ff]
[ 0.182839] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.182844] pci 0000:00:1f.2: PME# disabled
[ 0.182977] pci 0000:40:00.0: reg 10 64bit mmio: [0xf0400000-0xf040ffff]
[ 0.183086] pci 0000:40:00.0: PME# supported from D3hot D3cold
[ 0.183092] pci 0000:40:00.0: PME# disabled
[ 0.183126] pci 0000:40:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.183209] pci 0000:00:1c.1: bridge 32bit mmio: [0xf0200000-0xf04fffff]
[ 0.183268] pci 0000:00:1e.0: transparent bridge
[ 0.183294] pci_bus 0000:00: on NUMA node 0
[ 0.183301] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.183558] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCX1._PRT]
[ 0.183666] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCX2._PRT]
[ 0.183779] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB_._PRT]
[ 0.184275] ACPI Warning for \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20090903/nspredef-336)
[ 0.197016] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 14 15)
[ 0.197162] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 14 15)
[ 0.197302] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 14 15)
[ 0.197443] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 14 15)
[ 0.197584] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 *11 14 15)
[ 0.197726] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *10 11 14 15)
[ 0.197865] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 14 15)
[ 0.198007] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
[ 0.198150] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.198164] vgaarb: loaded
[ 0.198192] PCI: Using ACPI for IRQ routing
[ 0.198192] hpet clockevent registered
[ 0.198192] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.198192] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.198192] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.204021] Switching to clocksource tsc
[ 0.205786] pnp: PnP ACPI init
[ 0.205810] ACPI: bus type pnp registered
[ 0.208841] pnp 00:0c: io resource (0xf800-0xf81f) overlaps 0000:00:1f.0 BAR 13 (0xf800-0xf87f), disabling
[ 0.208848] pnp 00:0c: io resource (0xf820-0xf83f) overlaps 0000:00:1f.0 BAR 13 (0xf800-0xf87f), disabling
[ 0.208853] pnp 00:0c: io resource (0xf840-0xf85f) overlaps 0000:00:1f.0 BAR 13 (0xf800-0xf87f), disabling
[ 0.208858] pnp 00:0c: io resource (0xf860-0xf87f) overlaps 0000:00:1f.0 BAR 13 (0xf800-0xf87f), disabling
[ 0.210082] pnp: PnP ACPI: found 15 devices
[ 0.210085] ACPI: ACPI bus type pnp unregistered
[ 0.210090] PnPBIOS: Disabled by ACPI PNP
[ 0.210113] system 00:0c: ioport range 0x400-0x41f has been reserved
[ 0.210118] system 00:0c: ioport range 0x420-0x43f has been reserved
[ 0.210122] system 00:0c: ioport range 0x440-0x45f has been reserved
[ 0.210126] system 00:0c: ioport range 0x460-0x47f has been reserved
[ 0.210130] system 00:0c: ioport range 0x480-0x48f has been reserved
[ 0.210134] system 00:0c: ioport range 0xfa00-0xfa3f has been reserved
[ 0.210138] system 00:0c: ioport range 0xfc00-0xfc7f has been reserved
[ 0.210143] system 00:0c: ioport range 0xfc80-0xfcff has been reserved
[ 0.210147] system 00:0c: ioport range 0xfe00-0xfe7f has been reserved
[ 0.210151] system 00:0c: ioport range 0xfe80-0xfeff has been reserved
[ 0.210166] system 00:0d: ioport range 0x4d0-0x4d1 has been reserved
[ 0.210175] system 00:0e: iomem range 0x0-0x9ffff could not be reserved
[ 0.210180] system 00:0e: iomem range 0x100000-0x2fffffff could not be reserved
[ 0.210185] system 00:0e: iomem range 0xe8000-0xfffff could not be reserved
[ 0.210189] system 00:0e: iomem range 0xfec01000-0xffffffff has been reserved
[ 0.210193] system 00:0e: iomem range 0xd0000000-0xdfffffff has been reserved
[ 0.210198] system 00:0e: iomem range 0xcd800-0xe7fff has been reserved
[ 0.245086] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:20
[ 0.245092] pci 0000:00:1c.0: IO window: 0x2000-0x2fff
[ 0.245099] pci 0000:00:1c.0: MEM window: 0x30000000-0x301fffff
[ 0.245105] pci 0000:00:1c.0: PREFETCH window: 0x00000030200000-0x000000303fffff
[ 0.245113] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:40
[ 0.245118] pci 0000:00:1c.1: IO window: 0x3000-0x3fff
[ 0.245124] pci 0000:00:1c.1: MEM window: 0xf0200000-0xf04fffff
[ 0.245129] pci 0000:00:1c.1: PREFETCH window: 0x00000030400000-0x000000305fffff
[ 0.245137] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05
[ 0.245140] pci 0000:00:1e.0: IO window: disabled
[ 0.245145] pci 0000:00:1e.0: MEM window: disabled
[ 0.245150] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.245169] pci 0000:00:1c.0: setting latency timer to 64
[ 0.245186] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.245191] pci 0000:00:1c.1: setting latency timer to 64
[ 0.245200] pci 0000:00:1e.0: setting latency timer to 64
[ 0.245208] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.245212] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 0.245216] pci_bus 0000:20: resource 0 io: [0x2000-0x2fff]
[ 0.245220] pci_bus 0000:20: resource 1 mem: [0x30000000-0x301fffff]
[ 0.245224] pci_bus 0000:20: resource 2 pref mem [0x30200000-0x303fffff]
[ 0.245228] pci_bus 0000:40: resource 0 io: [0x3000-0x3fff]
[ 0.245232] pci_bus 0000:40: resource 1 mem: [0xf0200000-0xf04fffff]
[ 0.245236] pci_bus 0000:40: resource 2 pref mem [0x30400000-0x305fffff]
[ 0.245240] pci_bus 0000:05: resource 3 io: [0x00-0xffff]
[ 0.245244] pci_bus 0000:05: resource 4 mem: [0x000000-0xffffffff]
[ 0.245288] NET: Registered protocol family 2
[ 0.245412] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.245931] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.246991] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.247549] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.247553] TCP reno registered
[ 0.247696] NET: Registered protocol family 1
[ 0.247766] pci 0000:00:02.0: Boot video device
[ 0.247794] pci 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 0.247813] pci 0000:00:1d.0: PCI INT A disabled
[ 0.247830] pci 0000:00:1d.1: PCI INT B -> GSI 18 (level, low) -> IRQ 18
[ 0.247848] pci 0000:00:1d.1: PCI INT B disabled
[ 0.247860] pci 0000:00:1d.2: PCI INT C -> GSI 21 (level, low) -> IRQ 21
[ 0.247878] pci 0000:00:1d.2: PCI INT C disabled
[ 0.247889] pci 0000:00:1d.3: PCI INT D -> GSI 22 (level, low) -> IRQ 22
[ 0.247909] pci 0000:00:1d.3: PCI INT D disabled
[ 0.247927] pci 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 0.247960] pci 0000:00:1d.7: PCI INT A disabled
[ 0.248043] Unpacking initramfs...
[ 0.570705] Freeing initrd memory: 8514k freed
[ 0.580963] audit: initializing netlink socket (disabled)
[ 0.580981] type=2000 audit(1353673051.579:1): initialized
[ 0.584836] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.586913] VFS: Disk quotas dquot_6.5.2
[ 0.586993] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.587108] msgmni has been set to 1495
[ 0.587427] alg: No test for stdrng (krng)
[ 0.587515] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.587520] io scheduler noop registered
[ 0.587522] io scheduler anticipatory registered
[ 0.587525] io scheduler deadline registered
[ 0.587578] io scheduler cfq registered (default)
[ 0.587725] pcieport 0000:00:1c.0: irq 24 for MSI/MSI-X
[ 0.587738] pcieport 0000:00:1c.0: setting latency timer to 64
[ 0.587910] pcieport 0000:00:1c.1: irq 25 for MSI/MSI-X
[ 0.587921] pcieport 0000:00:1c.1: setting latency timer to 64
[ 0.588157] isapnp: Scanning for PnP cards...
[ 0.941304] isapnp: No Plug & Play device found
[ 0.943279] Linux agpgart interface v0.103
[ 0.943382] agpgart-intel 0000:00:00.0: Intel 915G Chipset
[ 0.943884] agpgart-intel 0000:00:00.0: detected 7932K stolen memory
[ 0.946905] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xe0000000
[ 0.947007] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.947124] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.947551] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.947793] PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
[ 0.950565] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.950576] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.950688] mice: PS/2 mouse device common for all mice
[ 0.950754] rtc_cmos 00:03: RTC can wake from S4
[ 0.950815] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 0.950845] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 0.950865] cpuidle: using governor ladder
[ 0.950868] cpuidle: using governor menu
[ 0.950874] No iBFT detected.
[ 0.951380] TCP cubic registered
[ 0.951551] NET: Registered protocol family 10
[ 0.952718] Mobile IPv6
[ 0.952722] NET: Registered protocol family 17
[ 0.952747] Using IPI No-Shortcut mode
[ 0.952851] PM: Resume from disk failed.
[ 0.952867] registered taskstats version 1
[ 0.953173] rtc_cmos 00:03: setting system clock to 2012-11-23 12:17:32 UTC (1353673052)
[ 0.953229] Initalizing network drop monitor service
[ 0.953259] Freeing unused kernel memory: 380k freed
[ 0.953642] Write protecting the kernel text: 2508k
[ 0.953671] Write protecting the kernel read-only data: 920k
[ 0.978733] udev[56]: starting version 164
[ 1.160248] usbcore: registered new interface driver usbfs
[ 1.160296] usbcore: registered new interface driver hub
[ 1.161028] usbcore: registered new device driver usb
[ 1.182569] SCSI subsystem initialized
[ 1.190338] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.190415] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 1.190465] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 1.190475] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 1.190548] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 1.190644] ehci_hcd 0000:00:1d.7: debug port 1
[ 1.194554] ehci_hcd 0000:00:1d.7: cache line size of 128 is not supported
[ 1.194597] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xcfdc0000
[ 1.208022] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 1.208068] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.208074] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.208079] usb usb1: Product: EHCI Host Controller
[ 1.208084] usb usb1: Manufacturer: Linux 2.6.32-5-686 ehci_hcd
[ 1.208088] usb usb1: SerialNumber: 0000:00:1d.7
[ 1.208278] usb usb1: configuration #1 chosen from 1 choice
[ 1.208343] hub 1-0:1.0: USB hub found
[ 1.208361] hub 1-0:1.0: 8 ports detected
[ 1.233134] libata version 3.00 loaded.
[ 1.252750] ata_piix 0000:00:1f.1: version 2.13
[ 1.252779] ata_piix 0000:00:1f.1: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 1.252850] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 1.252967] scsi0 : ata_piix
[ 1.253258] scsi1 : ata_piix
[ 1.253542] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x14e0 irq 14
[ 1.253548] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x14e8 irq 15
[ 1.253614] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.253623] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[ 1.254391] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.258173] FDC 0 is a post-1991 82077
[ 1.263545] tg3.c:v3.116 (December 3, 2010)
[ 1.263579] tg3 0000:40:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 1.263596] tg3 0000:40:00.0: setting latency timer to 64
[ 1.303402] tg3 0000:40:00.0: eth0: Tigon3 [partno(BCM95751) rev 4001] (PCI Express) MAC address 00:11:85:f4:68:94
[ 1.303409] tg3 0000:40:00.0: eth0: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1])
[ 1.303414] tg3 0000:40:00.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[ 1.303418] tg3 0000:40:00.0: eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[ 1.408033] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 1.408149] scsi2 : ata_piix
[ 1.408282] scsi3 : ata_piix
[ 1.408510] ata3: SATA max UDMA/133 cmd 0x1818 ctl 0x1830 bmdma 0x14f0 irq 19
[ 1.408516] ata4: SATA max UDMA/133 cmd 0x1820 ctl 0x1834 bmdma 0x14f8 irq 19
[ 1.419498] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 1.419514] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1.419520] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.419543] ata1.00: ATAPI: HL-DT-STDVD-ROM GDR8163B, 0B15, max UDMA/44
[ 1.419549] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 1.419586] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00001440
[ 1.419654] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.419660] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.419666] usb usb2: Product: UHCI Host Controller
[ 1.419673] usb usb2: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.419677] usb usb2: SerialNumber: 0000:00:1d.0
[ 1.419850] usb usb2: configuration #1 chosen from 1 choice
[ 1.419928] hub 2-0:1.0: USB hub found
[ 1.419946] hub 2-0:1.0: 2 ports detected
[ 1.420237] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 18 (level, low) -> IRQ 18
[ 1.420250] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 1.420255] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.420278] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 1.420326] uhci_hcd 0000:00:1d.1: irq 18, io base 0x00001460
[ 1.420387] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.420393] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.420398] usb usb3: Product: UHCI Host Controller
[ 1.420403] usb usb3: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.420407] usb usb3: SerialNumber: 0000:00:1d.1
[ 1.420517] usb usb3: configuration #1 chosen from 1 choice
[ 1.420581] hub 3-0:1.0: USB hub found
[ 1.420596] hub 3-0:1.0: 2 ports detected
[ 1.420694] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 21 (level, low) -> IRQ 21
[ 1.420706] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 1.420712] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.420729] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 1.420773] uhci_hcd 0000:00:1d.2: irq 21, io base 0x00001480
[ 1.420842] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.420849] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.420854] usb usb4: Product: UHCI Host Controller
[ 1.420858] usb usb4: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.420863] usb usb4: SerialNumber: 0000:00:1d.2
[ 1.421039] usb usb4: configuration #1 chosen from 1 choice
[ 1.421106] hub 4-0:1.0: USB hub found
[ 1.421122] hub 4-0:1.0: 2 ports detected
[ 1.421233] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 22 (level, low) -> IRQ 22
[ 1.421253] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 1.421259] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 1.421277] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 1.421321] uhci_hcd 0000:00:1d.3: irq 22, io base 0x000014a0
[ 1.421369] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.421373] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.421377] usb usb5: Product: UHCI Host Controller
[ 1.421380] usb usb5: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.421383] usb usb5: SerialNumber: 0000:00:1d.3
[ 1.421486] usb usb5: configuration #1 chosen from 1 choice
[ 1.421548] hub 5-0:1.0: USB hub found
[ 1.421561] hub 5-0:1.0: 2 ports detected
[ 1.428257] ata1.00: configured for UDMA/44
[ 1.432092] scsi 0:0:0:0: CD-ROM HL-DT-ST DVD-ROM GDR8163B 0B15 PQ: 0 ANSI: 5
[ 1.583348] ata3.00: ATA-8: WDC WD10EARS-003BB1, 80.00A80, max UDMA/133
[ 1.583354] ata3.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 1.589381] ata3.00: configured for UDMA/133
[ 1.589537] scsi 2:0:0:0: Direct-Access ATA WDC WD10EARS-003 80.0 PQ: 0 ANSI: 5
[ 1.607291] sd 2:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 1.607400] sd 2:0:0:0: [sda] Write Protect is off
[ 1.607407] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.607451] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.607718] sda: sda1 sda2 sda3
[ 1.624466] sd 2:0:0:0: [sda] Attached SCSI disk
[ 1.644177] sr0: scsi3-mmc drive: 40x/40x cd/rw xa/form2 cdda tray
[ 1.644184] Uniform CD-ROM driver Revision: 3.20
[ 1.644375] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 1.652589] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 1.652675] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 2.210227] PM: Starting manual resume from disk
[ 2.210234] PM: Resume from partition 8:2
[ 2.210236] PM: Checking hibernation image.
[ 2.210453] PM: Error -22 checking image file
[ 2.210457] PM: Resume from disk failed.
[ 2.232640] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 2.232645] EXT3-fs: write access will be enabled during recovery.
[ 2.268285] kjournald starting. Commit interval 5 seconds
[ 2.268307] EXT3-fs: sda1: orphan cleanup on readonly fs
[ 2.268317] ext3_orphan_cleanup: deleting unreferenced inode 803131
[ 2.268352] EXT3-fs: sda1: 1 orphan inode deleted
[ 2.268355] EXT3-fs: recovery complete.
[ 2.270491] EXT3-fs: mounted filesystem with ordered data mode.
[ 3.109167] udev[307]: starting version 164
[ 3.550275] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 3.550300] ACPI: Power Button [PBTN]
[ 3.550455] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 3.550467] ACPI: Power Button [PWRF]
[ 3.568817] processor LNXCPU:00: registered as cooling_device0
[ 3.573734] processor LNXCPU:01: registered as cooling_device1
[ 3.678953] input: PC Speaker as /devices/platform/pcspkr/input/input2
[ 3.815492] intel_rng: Firmware space is locked read-only. If you can't or
[ 3.815497] intel_rng: don't want to disable this in firmware setup, and if
[ 3.815499] intel_rng: you are certain that your system has a functional
[ 3.815502] intel_rng: RNG, try using the 'no_fwh_detect' option.
[ 3.910472] [drm] Initialized drm 1.1.0 20060810
[ 3.916477] parport_pc 00:07: reported by Plug and Play ACPI
[ 3.916548] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 4.130778] ACPI: WMI: Mapper loaded
[ 4.259603] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 4.259612] pci 0000:00:02.0: setting latency timer to 64
[ 4.265524] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 4.457976] Error: Driver 'pcspkr' is already registered, aborting...
[ 4.463841] Intel ICH 0000:00:1e.2: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 4.463903] Intel ICH 0000:00:1e.2: setting latency timer to 64
[ 4.884028] intel8x0_measure_ac97_clock: measured 54786 usecs (2639 samples)
[ 4.884033] intel8x0: clocking to 48000
[ 5.174304] Adding 4882424k swap on /dev/sda2. Priority:-1 extents:1 across:4882424k
[ 5.348170] EXT3 FS on sda1, internal journal
[ 5.443892] loop: module loaded
[ 5.923217] kjournald starting. Commit interval 5 seconds
[ 5.923637] EXT3 FS on sda3, internal journal
[ 5.923648] EXT3-fs: mounted filesystem with ordered data mode.
[ 6.341605] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 7.897825] tg3 0000:40:00.0: eth0: Link is up at 100 Mbps, full duplex
[ 7.897831] tg3 0000:40:00.0: eth0: Flow control is off for TX and off for RX
[ 7.898067] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 17.968015] eth0: no IPv6 routers present

elmig 11-24-2012 04:37 PM

If you're using a TFT monitor press Auto button.

widget 11-24-2012 07:58 PM

What happens if you boot in recovery mode?

elmig 11-25-2012 03:05 AM

I suspect sync/res not fully suported by monitor. It happened on a old Samsung TFT i had. Pressing autosync on the monitor shows full image.

acastano 11-25-2012 07:25 AM

Thank you for all these answers.

@ elming: it is indeed a TFT monitor, I will press auto button and keep you informed, thanks.
@ widget: if I boot in recovery mode, the prompt is shown and I can log in, do you have any idea? Thanks.

widget 11-25-2012 10:03 AM

It is good to hear that recoverry does boot.

You say you can log in. As your normal user? To the desktop?

When you boot recovery the first prompt you get will give you a root prompt. If you hit Ctrl + d at that point it will take you to a tty login where you can give your user name and password.

After doing that you should be able to type;
Code:

startx
and get to the desktop.

If this works then your problem is with your display manager. Reinstalling it may be what you need to do. This could be done easily after you get to the desktop or from the root prompt in recovery mode.


All times are GMT -5. The time now is 03:19 AM.