LinuxQuestions.org
Help answer threads with 0 replies.
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Distributions > Debian
User Name
Password
Debian This forum is for the discussion of Debian Linux.

Notices

Reply
 
Search this Thread
Old 08-10-2006, 03:21 AM   #1
kpachopoulos
Member
 
Registered: Feb 2004
Location: Athens, Greece
Distribution: Gentoo,FreeBSD, Debian
Posts: 704

Rep: Reputation: 30
cannot find usb port of my connected printer


Hi,
i have connected my Kyocera-Mita FS-1010 printer on my Debian Etch kernel 2.6.8-i386 system. It had been working in previous Debian releases, but now all print requests seem to just wait in the spooler queue forever. CUPS cannot seem to find the printer either in "/dev/usblp0" or "/dev/usb/lp0" -i get "Unable to open USB device "usb:/dev/usb/lp0": No such device" and the same for usblp0. I use a tried-and-tested Kyocera PPD file. Here is the "dmesg" output:
Code:
U exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
init IO_APIC IRQs
 IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1999.0406 MHz.
..... host bus clock speed is 333.0234 MHz.
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Freeing initrd memory: 4216k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfbaf0, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 11 12) *5
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [ALKA] (IRQs *20)
ACPI: PCI Interrupt Link [ALKB] (IRQs *21)
ACPI: PCI Interrupt Link [ALKC] (IRQs *22)
ACPI: PCI Interrupt Link [ALKD] (IRQs *23)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fc5c0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xc5f0, dseg 0xf0000
pnp: 00:0b: ioport range 0x3f0-0x3f1 has been reserved
PnPBIOS: 16 nodes reported by PnP BIOS; 16 recorded by driver
PCI: Using ACPI for IRQ routing
ACPI: PCI interrupt 0000:00:07.0[A] -> GSI 18 (level, low) -> IRQ 169
ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 177
ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 177
ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 185
ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 193
ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23
ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 201
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 209
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
.......    : physical APIC id: 02
.......    : Delivery Type: 0
.......    : LTS          : 0
.... register #01: 00178003
.......     : max redirection entries: 0017
.......     : PRQ implemented: 1
.......     : IO APIC version: 0003
.... IRQ redirection table:
 NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
 00 000 00  1    0    0   0   0    0    0    00
 01 001 01  0    0    0   0   0    1    1    39
 02 001 01  0    0    0   0   0    1    1    31
 03 001 01  0    0    0   0   0    1    1    41
 04 001 01  0    0    0   0   0    1    1    49
 05 001 01  0    0    0   0   0    1    1    51
 06 001 01  0    0    0   0   0    1    1    59
 07 001 01  0    0    0   0   0    1    1    61
 08 001 01  0    0    0   0   0    1    1    69
 09 001 01  0    1    0   1   0    1    1    71
 0a 001 01  0    0    0   0   0    1    1    79
 0b 001 01  0    0    0   0   0    1    1    81
 0c 001 01  0    0    0   0   0    1    1    89
 0d 001 01  0    0    0   0   0    1    1    91
 0e 001 01  0    0    0   0   0    1    1    99
 0f 001 01  0    0    0   0   0    1    1    A1
 10 001 01  1    1    0   1   0    1    1    D1
 11 000 00  1    0    0   0   0    0    0    00
 12 001 01  1    1    0   1   0    1    1    A9
 13 000 00  1    0    0   0   0    0    0    00
 14 001 01  1    1    0   1   0    1    1    B1
 15 001 01  1    1    0   1   0    1    1    B9
 16 001 01  1    1    0   1   0    1    1    C1
 17 001 01  1    1    0   1   0    1    1    C9
Using vector-based indexing
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ209 -> 0:16
IRQ169 -> 0:18
IRQ177 -> 0:20
IRQ185 -> 0:21
IRQ193 -> 0:22
IRQ201 -> 0:23
.................................... done.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
PCI: Via IRQ fixup for 0000:00:10.0, from 10 to 9
PCI: Via IRQ fixup for 0000:00:10.1, from 10 to 9
PCI: Via IRQ fixup for 0000:00:10.2, from 11 to 9
PCI: Via IRQ fixup for 0000:00:10.3, from 11 to 9
PCI: Via IRQ fixup for 0000:00:11.5, from 5 to 1
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4216 blocks [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 204k freed
vesafb: framebuffer at 0xe0000000, mapped to 0xf8824000, size 3072k
vesafb: mode is 1024x768x16, linelength=2048, pages=41
vesafb: protected mode interface info at c000:5606
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
fb0: VESA VGA frame buffer device
Console: switching to colour frame buffer device 128x48
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 177
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
    ide0: BM-DMA at 0xe700-0xe707, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xe708-0xe70f, BIOS settings: hdc:DMA, hdd:DMA
hda: ST340014A, ATA DISK drive
hdb: WDC WD2000JB-00GVA0, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 1024KiB
hda: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
 /dev/ide/host0/bus0/target0/lun0: p1 p2 p3 < p5 p6 p7 p8 p9 >
hdb: max request size: 1024KiB
hdb: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63, UDMA(100)
 /dev/ide/host0/bus0/target1/lun0: p1 p2 p3 < p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 >
hdc: CD-W540E, ATAPI CD/DVD-ROM drive
hdd: TSSTcorpDVD-ROM TS-H352A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 2305288k swap on /dev/hda7.  Priority:-1 extents:1
EXT3 FS on hda2, internal journal
Real Time Clock Driver v1.12
Generic RTC Driver v1.07
hdc: ATAPI 48X CD-ROM CD-R/RW drive, 8192kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM drive, 512kB Cache, UDMA(33)
input: ImExPS/2 Generic Explorer Mouse on isa0060/serio1
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
libata version 1.02 loaded.
Capability LSM initialized
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com
cdrom: open failed.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NTFS driver 2.1.15 [Flags: R/O MODULE].
NTFS volume version 3.0.
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on hdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on hdb2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
8139too Fast Ethernet driver 0.9.27
ACPI: PCI interrupt 0000:00:07.0[A] -> GSI 18 (level, low) -> IRQ 169
eth0: RealTek RTL8139 at 0xe000, 00:11:6b:36:b3:86, IRQ 169
eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
via-rhine.c:v1.10-LK1.1.20-2.6 May-23-2004 Written by Donald Becker
ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 201
eth1: VIA Rhine II at 0xed00, 00:11:09:72:01:51, IRQ 201.
eth1: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000.
sata_via version 0.20
ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 177
sata_via(0000:00:0f.0): routed to hard irq line 11
ata1: SATA max UDMA/133 cmd 0xE100 ctl 0xE202 bmdma 0xE500 irq 177
ata2: SATA max UDMA/133 cmd 0xE300 ctl 0xE402 bmdma 0xE508 irq 177
ata1: no device found (phy stat 00000000)
scsi0 : sata_via
ata2: no device found (phy stat 00000000)
scsi1 : sata_via
Via 686a/8233/8235 audio driver 1.9.1-ac4-2.5
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 193
via82cxxx: Six channel audio available
PCI: Setting latency timer of device 0000:00:11.5 to 64
ac97_codec: AC97 Audio codec, id: VIA112 (Unknown)
via82cxxx: board #1 at 0xEC00, IRQ 193
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 185
uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:10.0: irq 185, io base 0000e800
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 185
uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
uhci_hcd 0000:00:10.1: irq 185, io base 0000e900
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 185
uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3)
uhci_hcd 0000:00:10.2: irq 185, io base 0000ea00
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 185
uhci_hcd 0000:00:10.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#4)
uhci_hcd 0000:00:10.3: irq 185, io base 0000eb00
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 185
ehci_hcd 0000:00:10.4: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:10.4: irq 185, pci mem f8d15000
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA KM400/KM400A chipset
agpgart: Maximum main memory to use for agp memory: 816M
agpgart: AGP aperture is 128M @ 0xd8000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
input: PC Speaker
inserting floppy driver for 2.6.8-2-386
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
ACPI: Processor [CPU0] (supports C1)
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Fan [FAN] (on)
ACPI: Thermal Zone [THRM] (55 C)
lp0: using parport0 (interrupt-driven).
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02cc960(lo)
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
eth0: Promiscuous mode enabled.
device eth0 entered promiscuous mode
[drm] Initialized radeon 1.11.0 20020828 on minor 0: ATI Technologies Inc Radeon RV200 QW [Radeon 7500]
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Device is in legacy mode, falling back to 2.x
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
eth1: no IPv6 routers present
eth0: no IPv6 routers present
via_audio: ignoring drain playback error -11
via_audio: ignoring drain playback error -11
via_audio: ignoring drain playback error -11
usb 2-2: new full speed USB device using address 2
usb 2-2: USB disconnect, address 2
usb 1-2: new full speed USB device using address 2
ISO 9660 Extensions: Microsoft Joliet Level 1
ISOFS: changing to secondary root
via_audio: ignoring drain playback error -11
kostas@vakhos:~$
and "lsusb":
Code:
kostas@vakhos:~$ lsusb
Bus 005 Device 001: ID 0000:0000
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 002: ID 0482:0003 Kyocera Corp.
Bus 001 Device 001: ID 0000:0000
Also an "/etc/init.d/hotplug start" prints the following:
Code:
kostas@vakhos:~$ /etc/init.d/hotplug start
Starting hotplug subsystem:
   pci
     via-agp: already loaded
     pciehp: can't be loaded
missing kernel or user mode driver pciehp
     shpchp: can't be loaded
missing kernel or user mode driver shpchp
     8139cp: already loaded
     8139too: already loaded
     sata_via: already loaded
     via82cxxx: already loaded
     uhci-hcd: already loaded
     uhci-hcd: already loaded
     uhci-hcd: already loaded
     uhci-hcd: already loaded
     ehci-hcd: already loaded
     via82cxxx_audio: already loaded
     snd-via82xx: already loaded
     via-rhine: already loaded
     ignoring pci display device 01:00.0
   pci      [success]
   usb
     usblp: can't be loaded <---------------???????????
missing kernel or user mode driver usblp
   usb      [success]
   isapnp
     rtc: loaded successfully
     pcspkr: loaded successfully
     psmouse: loaded successfully
     floppy: loaded successfully
     parport_pc: loaded successfully
   isapnp   [success]
   ide
   ide      [success]
   input
     evdev: already loaded
     evdev: already loaded
     mousedev: already loaded
     tsdev: already loaded
     evdev: already loaded
   input    [success]
   scsi
   scsi     [success]
done.
What's the problem? Doesn't "usblp" exist in the kernel? Do i have to recompile it????? Ideas?
Thanks
 
Old 08-10-2006, 07:29 AM   #2
kpachopoulos
Member
 
Registered: Feb 2004
Location: Athens, Greece
Distribution: Gentoo,FreeBSD, Debian
Posts: 704

Original Poster
Rep: Reputation: 30
I solved my problem with "modprobe usblp"; i thought restarting hotplug would load the "usblp" module.
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Installing Linux on External hard drive connected by USB port omidiora Linux - Newbie 1 04-29-2006 09:51 AM
Strange...can't share usb printer connected to xp pc vatman Linux - Software 2 11-02-2005 06:50 PM
How can I share a USB printer connected to my Win XP computer through a Netgear RP614 PadreFabuloso Linux - Networking 12 06-15-2005 12:15 AM
Can't find parallel port /printer Richard Perry Linux - Hardware 1 03-04-2005 07:33 PM
External CD-R Drive Connected to Printer Port mfsjas Linux - Software 2 02-18-2002 08:05 PM


All times are GMT -5. The time now is 03:12 AM.

Main Menu
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
identi.ca: @linuxquestions
Facebook: linuxquestions Google+: linuxquestions
Open Source Consulting | Domain Registration