LinuxQuestions.org
Visit Jeremy's Blog.
Go Back   LinuxQuestions.org > Linux Answers > Networking
User Name
Password

Notices


By unixfoo at 2007-11-12 09:53
More Details on : http://unixfoo.blogspot.com/

Howto : Linux bonding

Bonding is creation of a single bonded interface by combining 2 or more ethernet interfaces. This helps in high availability and performance improvement.

Steps for bonding in Fedora Core and Redhat Linux

Step 1.

Create the file ifcfg-bond0 with the IP address, netmask and gateway. Shown below is my test bonding config file.

$ cat /etc/sysconfig/network-scripts/ifcfg-bond0

DEVICE=bond0
IPADDR=192.168.1.12
NETMASK=255.255.255.0
GATEWAY=192.168.1.1
USERCTL=no
BOOTPROTO=none
ONBOOT=yes

Step 2.

Modify eth0, eth1 and eth2 configuration as shown below. Comment out, or remove the ip address, netmask, gateway and hardware address from each one of these files, since settings should only come from the ifcfg-bond0 file above.

$ cat /etc/sysconfig/network-scripts/ifcfg-eth0

DEVICE=eth0
BOOTPROTO=none
#HWADDR=00:12:17:5C:A7:9D
#IPADDR=192.168.1.12
#NETMASK=255.255.255.0
#TYPE=Ethernet
#GATEWAY=192.168.1.1
#USERCTL=no
#IPV6INIT=no
#PEERDNS=yes
ONBOOT=yes
# Settings for Bond
MASTER=bond0
SLAVE=yes

$ cat /etc/sysconfig/network-scripts/ifcfg-eth1

DEVICE=eth1
BOOTPROTO=none
#HWADDR=01:12:18:5C:A7:D9
#IPADDR=192.168.1.13
#NETMASK=255.255.255.0
ONBOOT=yes
#TYPE=Ethernet
USERCTL=no
#IPV6INIT=no
#PEERDNS=yes
#
# Settings for bonding
MASTER=bond0
SLAVE=yes
$ cat /etc/sysconfig/network-scripts/ifcfg-eth2

DEVICE=eth2
BOOTPROTO=none
#HWADDR=00:12:27:5C:A7:9D
#IPADDR=192.168.1.12
#NETMASK=255.255.255.0
ONBOOT=yes
#TYPE=Ethernet
#GATEWAY=192.168.1.1
#USERCTL=no
#IPV6INIT=no
#PEERDNS=yes
MASTER=bond0
SLAVE=yes

Step 3.

Set the parameters for bond0 bonding kernel module. Add the following lines to /etc/modprobe. conf

# bonding commands
alias bond0 bonding
options bond0 mode=balance- alb miimon=100

Step 4.

Load the bond driver module from the command prompt.

$ modprobe bonding

Step 5.

Restart the network, or restart the computer.

$ service network restart # Or restart computer

When the machine boots up check the proc settings.

$ cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.0.2 (March 23, 2006)

Bonding Mode: adaptive load balancing
Primary Slave: None
Currently Active Slave: eth2
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0

Slave Interface: eth2
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:13:72:80: 62:f0

Look at ifconfig -a and check that your bond0 interface is active. You are done!


  



All times are GMT -5. The time now is 07:06 AM.

Main Menu
Advertisement
Advertisement
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
Open Source Consulting | Domain Registration